Search Documents

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By Armando Díaz

Anteriormente, el objetivo de las organizaciones empresariales era la optimización de los procesos productivos a través de una limitada eficiencia en el mercado. Sin embargo, esta situación ha cambiado, dado que para ingresar al mercado y mantenerse rentable, se requiere una mayor eficiencia y efectividad. Por ello, el presente trabajo describe el punto de equilibrio como herramienta en el proceso de gestión, donde se igualan los ingresos totales y los costos totales a cero. Son tres los métodos utilizados para la determinación en el punto de equilibrio: ecuación, margen de contribución y gráfico. En este sentido, se utiliza el método gráfico ya que define las ecuaciones de costos totales y es fácilmente comprensible a todo nivel.

Sep 13, 2001

Analysis of Procedures and Drivers for Industrial Waste Management

Sep 13, 2010

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

Most statistical and geostatistical methods of re-source and reserve estimation work extremely well for Normal (Gaussian) well-behaved information. However, most interesting mineral deposits exhibit far from this idealistic distribution of values. It seems that the more valuable the mineral, the less likely the data are to have a Normal distribution. Values tend to be "positively skewed" with a long tail into the high values. Using averaging techniques, such as inverse distance or ordinary kriging may result in consider-able overestimation of grades and tonnages unless such values are cut or otherwise modified. This paper presents some real case studies where distributions are (a) highly skewed and (b) the product of multiple phases of mineralisation. Practical methods are presented for solving such problems including combinations of indicator and log normal kriging methods. The emphasis of the presentation is on developing operational methods which can be used on project evaluation or grade control in producing mines.

Jan 1, 2000

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country's potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America's major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

"An estimated 600,000 tons of bentonite clay are used annually in the U. S. as binder for production of iron ore concentrate pellets. Since this is a significant cost item for the plants, and the addition of bentonite to the pellets contributes undesirable silica into the finished pellets, there is considerable incentive for finding methods to reduce bentonite use. One way to reduce bentonite levels is to selectively use those bentonites that are most effective in this application, so that a lower dosage will still produce a sufficiently strong pellet. Unfortunately, there are no satisfactory methods available for accurately predicting which bentonites are actually most effective, short of using them to actually make pellets. One of the popular methods for attempting to evaluate bentonites is the “Plate Water Absorption” (PWA) test. While some plant operators accept the PWA results as indicating the relative quality of bentonites, others disagree and claim that, over a fairly broad range of values, PWA does not correlate with bentonite performance.Since both Ca+2 and Mg+2 ions are known to reduce the swelling and water absorption capacity of bentonite, it was believed that the presence of these ions in plant recycle water could be changing the bentonite performance. Since the standard PWA test uses only distilled water for its measurements, it could not detect these effects. Experiments were therefore carried out on a number of different bentonites using a modified PWA tests, with plant recycle water replacing the distilled water. These experiments showed little effect of the plant water on the PWA value, and chemical analysis of the water showed that the levels of dissolved salts were quite low.Water and accompanying salts were then extracted from a magnetite concentrate filter cake by rinsing with distilled water. Analysis of this water showed an extremely high level of dissolved salts, particularly salts of calcium and magnesium. When concentrations were compared with the recycle water from the plant filters, it was determined that levels of Ca+2 and Mg+2 retained in the filter cake were over 500 times higher than levels in the recycle water. This extreme elevation of soluble salts in the filter cake is believed to be due to adsorption of these ions into the electrical double layer of the magnetite particles."

Jan 1, 2003

By K. J. R. Ford

"Significant advances in mining and metallurgical operations have occurred over the last two decades, to define ore bodies via geological mapping, mineralogical analyses, geostatistical models and resource reserve modeling. Metallurgical process measurement, controls and modeling have also significantly progressed, with advanced instrumentation, control software, data capture systems and simulation tools. This progress together with development of the science of geometallurgy has allowed geologists, mineralogists, miners and metallurgists to start working together to define geometallurgical ore units and link these to mine planning and projected metallurgical performance. However, application of full geometallurgical programs into existing mine-processing operations or into new “greenfield” projects has been slow. This is mainly due to higher costs, limited dedicated technical resources and little or no corporate leadership. Additionally, life-of-mine cash flow models, the “dollars”, have been largely driven by ore tonnage rates, pay-metal grades and fixed pay-metal percentage recoveries, with few or no geometallurgical parameters included.Here defined, the “electrons” represent intrinsic ore characteristics embracing chemical composition, mineralogy, gangue components and their associated fundamental metallurgical processing phenomena. With its ever expanding treasure chest of measurement and modeling tools, geometallurgy paints a much clearer picture of the “electrons” for the geologist and metallurgist. But to fully understand and realize the real net value of ores over the life of a mine, a comprehensive link of “electrons to the dollars” is essential. Intrinsic characteristics of geometallurgical ore units are by definition linked to their metallurgical processing, but importantly need also to be related to operating costs, capital requirements and revenue.This paper discusses this important linkage under topics of ore geology and mineralogy, metallurgical processing, waste disposal, environmental issues, metal refining, project engineering and lifeof- mine models. Topics are illustrated by multi-metal references and by case examples from gold ore heap leaching and manganese ore smelting projects. 1"

Jan 1, 2013

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

Jan 1, 1967

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

Map

Jan 1, 1941

By C. Hilgendorf, J. Gingerich, J. R. Boniwell, M. Drouin, D. David on, J. Boldy

The initial discovery of gold in the Eastmain River area, 310 km northeast of Chibougamau, was made by Placer Development Limited in 1970. This discovery resulted from the drill testing of an airborne E .M. Target located in an area of extensive glacial overburden, within an unexplored Archean greens tone belt considered prospective for base metal deposits. Intermittent exploration by another company between 1973-1977 failed to obtain promising results and the existing claims were allowed to lapse. In 1981, Placer reactivated the project and initiated intensive exploration during the next two years which included aerial E .M. surveys, claim staking, ground E .M. and magnetic surveys, geological mapping, diamond drilling and attendant borehole P,E.M. surveys. Beginning in 1983, exploration has been conducted on a joint venture basis with Eldor Resources Limited, The greenstone belt under investigation has an arcuate distribution pattern relative to a centrally located granitic core. Occurrences of gold mineralization defined to date are located to the south of the granite along a strike length of 7 km, and appear to be restricted to the lowermost of two mafic volcanic cycles. This lower cycle is dominated by basaltic flows with subordinate rhyolitic flows and pyroclas ties. Concordant, variably magnetic, massive to talcose ultramafic units occur towards the stratigraphic top of the lower mafic volcanic cycle and appear to crudely define areas considered prospective for gold on a regional bases. Economic interest in centered on a s tratabound, siliceous, sulphide-bearing unit hosted in a 15- 25 metre thick sequence of rhyolite tuffs, basalts and intercalated ultramafics, The siliceous ore bearing unit ( interpreted as a recrystallized chert) contains from 10%-30% pyrrhotite and pyrite with subordinate chalcopyri te and minor sphaleri te. Alteration is characterized by mica development, silicification and carbonatization. Garnets are also occasionally present in close proximity to the ore horizon. The sequence is south facing, and overturned to the northeast at 35°-55°. Explora tory drilling in the vicinity of two conductive targets has been on 100 metre centres along a 1 km strike length of the prospective sequence. To the end of 1983, two ore zones (A and B) have been partially drill tested with estimated indicated and inferred geological reserves of 1 million tonnes grading 11.7 g/t gold , 14.7 g/t silver and 0.26% copper. The system is open at depth. This discovery is the result of the effective integration of geophysics and geology with contributions by many over a long period of time. Key events that can be emphasized are: ( 1) initial area selection of a remote greenstone belt in 1969 - albeit for base metal deposits , (2) utilization of an airborne E .M. system which successfully targeted the A Zone in 1970 , (3) the timely reactivation of the project in 1981 and the subsequent recognition that the original discovery represented a sulphide bearing stratabound horizon with implicit volcanogenic connotations , (4) the intensive effort in 1982-83 deploying aerial and ground geophysics coupled to volcanogenic concepts of ore distribution which resulted in the discovery of the B and C Zones in 1982, and (5) the integration of downhole P . E.M. surveys and geology to successfully delineate ore at increasing depths . To the end of 1983 , $2.6 million has been expended, and it is hoped that continued effort will result in the eventual delineation of an economically viable ore deposit for the joint venture partners .

Jan 1, 1984

By L. A. Cornish, L. H. Chown, S. N. Prins, R. Süss, L. Glaner, A. Douglas

Platinum-based alloys are being developed for high temperature and special applications for good corrosion and oxidation resistance. The microstructures are similar to those of nickel-based super alloys, and comprise ~Pt3Al particles in a Pt-based matrix. After assessing binary alloys, the best candidate system was found to be Pt-Al. Testing and selection of alloys based on Pt-Al were undertaken, where the ternary additions comprised Ru, Cr, Ta, Ir and Ti. As well as phase characterization work, mechanical and oxidation tests were undertaken. The best alloys were found to be Pt-Al-Cr and Pt-Al-Ru. However, the volume fraction of the ~Pt3Al was only around40 per cent instead of the ~70 per cent found in Ni-based super alloys. To increase this, trials were conducted on a range of Pt-Al-Cr-Ru alloys, the optimum composition being Pt80:Al14:Cr3:Ru3.Currently, further additions are being made to the quaternary alloys to change selected properties. As well as developing the alloys themselves, another part of the project is to compile a thermodynamic database using Thermo-Calc?. Phase diagram work has been undertaken so that the results can be input to Thermo-Calc? so that the descriptions of the phases can be optimized. The final database will allow the phases and compositions of selected alloys to be derived, thus predicting the alloys? components without necessarily undertaking further experimental work. This will aid the development of the alloys and will be a useful tool to the final developers of the alloys. Good agreement with experimental data has been observed, which is very encouraging for usefulness of the database. Keywords: platinum-based alloys, intermetallic compounds, high temperature

Jan 1, 2004

By H. E. Urtubia, C. W. Bailey

"BHP-Billiton’s Minera Escondida Limitada is one of the world’s largest copper producers. It treats a combined 88 million tons of copper ore per year through its two concentrators: Los Colorados and Laguna Seca. Over the past three years, metallurgical sampling has been performed at the Laguna Seca concentrator to calibrate both the JKSimMet and JKSimFloat grinding and flotation simulators. In the past, the calibrated simulators have been used to predict the effect of changes in operating conditions in the grinding and flotation circuits separately. To assist in the development of future processing options, predictions were required of the effect of changing grinding circuit conditions on flotation performance. This was achieved by using an integrated grinding and flotation simulation. The grinding circuit performance was predicted under different operating conditions (such as tonnage rate and product grind size) using JKSimMet, and these results were then used in JKSimFloat to predict the flotation performance for the new grinding circuit product. This combination of the simulators allows both the effects of residence time and grind size on flotation performance to be investigated.This paper presents the first combined grinding and simulation modelling and simulation case study using JKSimMet and JKSimFloat. The modelling and simulation methodologies for the grinding and flotation circuits are discussed along with the circuit simulations that were performed. The simulator predictions are presented in conjunction with independent laboratory results of the new operating conditions. The ability to predict flotation circuit performance based on changes in grinding circuit performance is also discussed. This methodology provides improved predictions of flotation circuit performance when grinding circuit changes (including grinding capacity increases) are made.INTRODUCTIONOver the past decade, the grinding and flotation research groups at the Julius Krutschnitt Minerals Research Centre - JKMRC (Brisbane, Australia), University of Cape Town (Cape Town, South Africa) and McGill University (Montreal, Canada) have been developing a methodology for optimising grinding and flotation plants using actual plant data together with semi-empirical sub-process models. The project is being conducted as part of the Australian Minerals Industry Research Association (AMIRA) P9 Project, titled “The Optimisation of Mineral Processes by Modelling and Simulation”. The project first commenced in 1962 and is currently in its “Nth” phase."

Jan 1, 2007

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007