Search Documents

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By Andy Alder

The aim of this paper is to provide an overview and details of good practice, from a United Kingdom perspective, in the development and implementation of major tunnel and underground infrastructure projects. In doing so, it draws on a broad base of project management theory. A central theme is that successful project delivery is dependent on detailed planning of the complete project delivery process, forming an effective team that works well together and the proper management of risk. The role of partnering in forming a strong project coalition is described. Particular emphasis is given to the integration of design and construction, and the role of the designer throughout the construction phase. The implementation of risk management in the design and construction of tunnel works is discussed, and recommendations are made on how risk, value and constructability can be integrated in project delivery. Recent practice in project procurement, particularly in the use of innovative collaborative forms of contract are described, and details of particular provisions for joint management of risk and problem resolution are provided. Finally, the relevance of the ITIG Code of Practice for Risk Management of Tunnel Works to good practice in project delivery is highlighted throughout the paper.

Investigation of the Effect of N-Substituents on Performance of Thioureas as Special Collectors for Copper Sulfides by ab Initio Calculations

Sep 13, 2010

[ ]

Jan 1, 1938

By Mark Aylmore, Guy Deschenes

"Increasing pressure are motivating the gold mining industry to develop a substitute to cyanide for leaching gold. This effort in mainly based on the high toxicity of cyanide and on the lack of efficiency of cyanide in the treatment of mildly refractory gold ores (sulfides and pre-robbing). Consequently, in only a few years, consortia have been created to elucidate and implement a new technology. The most promising lixiviant that has been selected to replace cyanide is thiosulfate. This paper will present a critical analysis on the latest developments in thiosulfate leaching and illustrate the potential and limitations of the technology with experimental data. Finally an assessment of the cost and performance of thiosulfate leaching relative cyanidation will be evaluated.INTRODUCTIONConcerns regarding the toxicity of cyanide and inability of cyanide solution to effectively leach some carbonaceous gold ore or mild refractory gold ores have made the gold mining industry evaluate alternative lixiviants to leach gold. This concern has been heightened recently by the cyanide spill at a mine in Romania, which devastated a 250-mile stretch of the Danube River and its tributaries, and the environmental damage at Ok Tedi mine in Papua New Guinea. Some countries and locations have prohibited the application of cyanidation to recover gold, such as, California and Colorado States, Japan and Turkey etc.There are several potential non-cyanide lixiviants (Sparrow and Woodcock, 1995) for gold extraction, such as thiosulfate, thiourea and halogen. A pilot feasibility test (Marchant and Broughton, 1987) had suggested that thioureation might result in acutely toxic byproducts even after treatment. Scientists of Swedish Academic of Sciences reported that thiourea is a carcinogen. Halogen is also a pollutant to the environment. Thiosulfate leaching appears to have very good potential as an effective and less hazardous procedure for gold and silver extraction from auriferous ores. In addition to being much less toxic and relatively cheap, it forms a stable anionic complex with gold but is less reactive to other metals, for instances, copper and carbonaceous materials, in comparison with cyanide."

Jan 1, 2001

By M. Hermanus

1. INTRODUCTION It gives me great pleasure to extend my warmest greetings to everyone attending the 30th International Conference of Safety in Mines Research Institutes. I would also like to bid a special welcome to all of the international delegates who have travelled to Johannesburg to take part in what surely be a most rewarding session of deliberations. As you come together over next four days, you will have a wonderful opportunity to exchange ideas and information on strategies and practices for the implementation of sustainable patterns of development. The objectives of this meeting are both timely and far-reaching, as countries around the globe work towards the sustainable use of the world resources. Each of you brings a high level of expertise to these deliberations. I know that you will make the most of this opportunity to address the challenges and opportunities to highlight the most innovative and technologically efficient methods of social protection in order to ensure an increase in the quality of life, health, safety and living environment for the peoples of the Africa. Our country, although endowed with an immense and diverse array of mineral deposits, is perhaps best known in the mining industry for the fact that it is the world’s biggest producer of gold. Although South African gold production has declined over the past years and the industry faces serious problems, it is a myth that the South African industry is moribund. There is a new energy coursing through the South African producers which will ensure their powerful presence for many years to come, based not only on their domestic production but also and probably increasingly on their external operations. Africa features prominently in the latter category.

Jan 1, 2003

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By R. J. Pine, J. M. Rance, J. S. Coggan

ABSTRACT: The safe design of excavations created in a fractured rock mass is of paramount importance in rock engineering. Depending on the nature of the stress regime acting on an excavation, and the associated deformational behaviour of the rock mass surrounding the excavation, a number of potential failure mechanisms exist. These involve a combination of shear failure on existing joints, extension of critically oriented joints and propagation of new fractures through previously intact rock. Conventional numerical codes usually adopt either a continuum or discontinuum approach; this often results in significant over simplification and kinematic limitations particularly when modelling complex rock mass behaviour in the close vicinity of excavations. This paper describes the results from several case examples using a combined finite element-discrete element code, ELFEN that incorporates a crack propagation mode. Through the use of selected rock engineering examples, the authors demonstrate the potential of the code in the realistic simulation of complex rock failure both in underground and surface excavation applications. RÉSUMÉ: La conception sûre des excavations créées dans une masse de roche fracturée est d'importance primordiale dans la géotechnique. Selon la nature du régime d'effort autour d’une excavation, et le déformation associé de la masse de roche autour de l'excavation, il exsite un certain nombre de mécanismes potentiels d'échec. Ceux-ci comportent une combinaison d'échec de cisaillement sur les joints existants, la prolongation des joints d’orientation critique et la propagation de nouvelles ruptures dans la roche précédemment intacte. Les codes numériques conventionnels adoptent habituellement l’approche, soit d’un continuum, soit de discontinuum; ceci a souvent comme conséquence une sursimplification significative et les limitations cinématiques en particulier en modelant le comportement complexe de la masse de roche très proche des excavations. Cet article décrit les résultats de plusieurs exemples de cas en utilisant un code qui s’agit d’une combination d’élément discret et d'élément fini, ELFEN qui incorpore un mode de propagation de fissure. Par l'utilisation des exemples choisis géotechniques, les auteurs démontrent le potentiel du code dans la simulation réaliste de l'échec complexe de roche pour les applications aux excavations soit au fond soit à l’extérieure. ZUSAMMENFASSUNG: Das sichere Design der Aushöhlungen, die in einer zerbrochenen Felsenmasse verursacht werden, ist vom paramount Wert in der Felsentechnik. Abhängig von der Natur des Druckregimes, das auf einer Aushöhlung und dem dazugehörigen deformationalen Verhalten der Felsenmasse umgibt die Aushöhlung fungiert, bestehen eine Anzahl von möglichen Ausfalleinheiten. Diese beziehen eine Kombination des Scherausfalls auf vorhandenen Verbindungen, Verlängerung der kritisch orientierten Verbindungen und Ausbreitung der neuen Brüche durch vorher intakten Felsen. Herkömmliche numerische Codes nehmen normalerweise entweder ein kontinuum oder discontinuum Annäherung an; dieses ergibt häufig bedeutende Übervereinfachung und kinematische Beschränkungen, besonders wenn es kompliziertes Felsenmasseverhalten in der Nähe der Aushöhlungen modelliert. Dieses Papier beschreibt die Resultate von einigen Fallbeispielen mit einem kombinierten begrenzten Element - getrennten Elementcode, ELFEN, das einen Sprungausbreitungmodus enthält. Durch den Gebrauch von vorgewählten Felsentechnikbeispielen, demonstrieren die Autoren das Potential des Codes in der realistischen Simulation des komplizierten Felsenausfalls bei Anwendungen für beide Tagebaue und Untergrundsaushöhlungen.

Jan 1, 2003

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

In most surface mining operations, overall project economics is driven to a significant extent by the slope angles that can be achieved within the rock masses present. This is particularly true of precious metal pits in which stripping ratios can be relatively high, although examples from other non-precious metal operations (such as large iron ore and copper pits) can also be found. As a consequence, it is not surprising that in most large (deep) open pit mines, relatively small changes in slope angle (of the order of two or three degrees can translate into changes in project value measured in the tens or even hundreds of millions of dollars. Understanding how this potential value can be realised, and quantifying the associated risks, should be one of the key outcomes of modern slope engineering practice. In striving for optimised slope angles, therefore, mining companies and their specialist consultants are increasingly turning to more sophisticated methods of engineering open pit walls. This paper summarises contemporary slope engineering practice as well as some of the key technical issues that are either currently being researched or will need to be researched in the future. It is written in the context of the slope engineering process; namely, data collection and analysis, failure mode identification and stability assessment, slope design, slope formation, and slope (face) mapping and monitoring (the latter two activities being the primary on-going data collection functions that close the design loop).

Jan 1, 2002

By Ken Cross

This paper aims to demonstrate that explosives organizations and workers have a legal, moral and financial duty to be able to demonstrate their competence when required, and how that may be achieved at any level from explosives storekeeper to senior explosives engineer on a major project. The concept of competence is outlined, as are the benefits to members of staff, management and the organization, particularly in a regulatory regime that includes competence management as a key performance indicator.

Jan 1, 2013

By S. Ranganathan

Production of ferro-chromium in the submerged-arc furnace is highly energy-intensive. Several process rates have been attempted to reduce the specific energy consumption in the production of this alloy. An exhaustive understanding of the thermo-chemical features of the production process can be used to reduce the specific power consumption significantly. The knowledge can be used to reduce the energy drain through undesired reactions in the process can be minimised. Plant trials have shown that specific energy consumption up to 100kWh/tonne of hot metal can be obtained by adopting this strategy. The process requires modification in operation practice and does not require any capital investment unlike other processes adopted for reducing power consumption. The principle of thermo-chemistry involved in this process development and results of plant trials are discussed in detail.

Jan 1, 2007

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

"In order to achieve a high recovery of particles finer than 10µm, three types of dry Tower Mill (VD-1, KD-1, KD-2 and KD-3) have been developed. These mills differ from each other in the size of the comminuting part, the inside diameter and shape of the classifying part and the system involved in the collecting process. The last version (KD-3) of tower mills in which the comminuting and classifying operations has been separated, can produce particles finer than 10µm from a limestone ore sizing from 420 to 3360µm. In this tower mill, products in comminuting section are blown up and transported into the classifying column, made of an inverted cone on top of a cylinder, before they agglomerate and settle down. Fine particles are deported and recovered in a cyclone with a central spiral ribbon.Previous studies on the grinding efficiency of the tower mill KD-3 have shown how the maximum size of collected products increased with the airflow velocity, disturbing in the same way a smooth regulation of the grinding operation with the tower mill KD-3. A complete knowledge of factors that influence the maximum size of collected products is needed, therefore, to increase the efficiency of the grindingclassifying operation and ensure a better control over the collected products. The present study deals with this issue and, assuming that the structure of the classifying column could be one of these factors, its internal structure was modified (insertion of vertical plates, cone or horizontal nets) before carrying out comminution tests that would establish a relationship between the inward shape of the column and the maximum size of collected products. It was found that the weight of products collected in the cyclone decreases when a cone or some horizontal nets are inserted inside the column. At the same time, the weight of products collected in the column increases. This is due to the fact that coarse particles blown up from the comminution section collide with the base of the cone or the nets and settle down the bottom of the classifying column. Therefore, the cone and some horizontal nets inserted inside a classifying column, have the particularity to stabilize the maximum size of particles (15.1-17.5µm and 8.4-11.3µm) in the cyclone even when the airflow velocity in duct increased. These tools could of great help in the production of particles of definite size to fit for instance the paper industries requirements (production of limestone material sizing - 10µm as paper filler)."

Jan 1, 2003

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006