Search Documents

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By P. F. Ledwaba

South Africa?s Northern Cape Province houses a variety of gemstone minerals. Diamonds remain the primary gemstone in the province, but there are also tiger?s eye, sugilite, rose quartz, jasper, amethyst, amazonite, tourmaline, and topaz deposits. This paper gives an overview of the tiger?s eye (TE) mining sector in the Northern Cape, with the objective of assessing the potential of TE to contribute to job creation and poverty alleviation in the province. Mining of TE started in 1803, but gained momentum during the 1960s. Mining is conducted on a small-scale basis, and in most cases without any legal framework. The majority of the residents are not benefiting from TE. It has been reported that an estimated R700 000 to R800 000 worth of TE is leaving the country every week through illegal trading. The potential for TE mining to contribute to socioeconomic development is hindered by illegal operations, lack of technical skills and knowledge, exploitation by dealers, lack of market information, community rivalries, and absence of value addition. A multi-stakeholder approach is needed to formalize the sector and reap the benefits. Mintek is spearheading a TE project in the Prieska area of the Northern Cape, which aims to establish a gemmological centre where TE can be beneficiated into saleable and high-value products..

Jan 1, 2014

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

By Elliott A, Kingsnorth D. J

The development of a large high grade spodumene orebody, in excess of 30M tonnes containing at least 7M tonnes at 4.0% Li20, by Lithium Australia Ltd at Greenbushes, Western Australia is significantly increasing the world consumption of lithium minerals. The availability of two low cost sources of lithium, spodumene concentrates (7.5% Li20) and glass grade spodumene (4.8% Li20) has been welcomed by the ceramic and glass industries as it assists them to lower their raw material costs at a time when they are facing severe competition from alternative materials. While there is no shortage of lithium reserves in the world, there has been a shortage of high quality lithium minerals. The Lithium Australia development has filled this need. The favourable factors of high grade, low impurities, open cut mining and existing infrastructure make this an ideal low cost source for a long term downstream lithium industry. The Lithium Australia mine development has filled the need for a reliable long term supply of lithium minerals. The long term viability of this resource is ensured by the unique combination of the following key attributes of the development : High grade reserves of 7.OM tonnes of 4.0% Li20 within 130 metres of the surface, contained within a total proven reserve of 30M tonnes of 2.8 % Li20. Open pit mining with stripping ratio of less than 2.5:1 waste:ore. Low impurities levels, particularly in those elements, that have a detrimental effect on the colour of glass/ceramics i.e. iron, manganese, titanium and chromium. An existing mine infrastructure that includes an adequate water supply for all foreseeable processing requirements. A sophisticated spodumene concentrator utilizing statistical process control to produce a consistently high grade product with minimal impurities. A technically qualified stable workforce fully acquainted with spodumene processing techniques. Greenbushes high grade concentrates have found ready acceptance in the specialty ceramic and glass industries during the past four years. The consistency and high grade/low impurity level of the product has enabled its use in the production of television tubes, oven to table ware, glass fibres, specialty glasses and ceramic glazes.

Jan 1, 1989

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

Kudremukh Iron Ore Company Ltd, a wholly owned Government of India Enterprise, was established in the year 1976 to develop mine and plant facilities to produce 7.5 Mtpa of high-grade iron ore concentrate at Kudremukh. The mine and plant facilities were commissioned in 1980. In view of high demand for iron oxide pellets in iron and steel industry worldwide and as a diversification activity, a pelletisation plant of 3.0 Mtpa capacity was commissioned in the year 1987 at Mangalore for production of high-quality blast furnace and direct reduction grade pellets for export. The pellet plant capacity has been increased to 3.5 Mtpa by technological improvement which included installation of roll press for quality and productivity improvement. In addition, the pellet capacity is being increased to 4 Mtpa by the addition of Shaft Pelletising Furnace plant.

Jan 1, 1999

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By Benkendorff P. N

Cement production in Australia approximates 6.5 million tonnes per year. Cement clinker is sourced from 15 plants which operate 28 kilns. Cement grinding is conducted at 14 of the clinker plants plus 7 grinding plants. Average annual capacity per kiln or plant is lower than in many overseas countries, but kilns introduced since 1970's have been of larger size more in keeping with size trends overseas, although still smaller than the large units overseas. Substantial economies in capital and labour costs can be achieved in large production units, particularly with dry process kilns using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. Precalcination techniques have been introduced to the Australian cement industry but as cement transport costs form a major part of supplying diverse market areas, the size of kilns is likely to remain less than maximum owing to balance with distribution costs. The cement industry uses significant amounts of thermal and electrical energy which can be minimised by proper selection of equipment and technology. Labour costs are also significant and can be contained by automation and computer control of the process.

Jan 1, 1989

For the first time in its history the Institute will hold a meeting in the State of Arizona. A few years ago Arizona stood third in the copper-producing districts of the United States. Since that time, with the development of porphyry mines, the output has gone up with great rapidity until it not only is the leading district, but its output at the present time is at the rate of nearly double the Montana output, which now stands second in the list. In connection with this .development, most interesting departures have been made in methods -of mining, concentration and smelting. Principles of mining and metallurgy of the greatest interest will be covered by papers which will' appear in the Bulletin and be presented at Technical Sessions, while ample opportunity will be afforded for those who go to the meeting to see all the points of interest .to them. In addition, members will be well rewarded by the marvelous natural features to be seen on the trip, including 'the petrified forests, the cliff dwellings on the Apache Trail and the Grand Canyon of Arizona. It is planned to start the special train from New York, but members and guests may join the special at other points en route as indicated by the following schedule: ITINERARY . , Thursday, September 14th Lv New York, Grand Central Terminal.. ............... 5.30 p. m. Dinner in dining car a la carte New England Members via B. & A. R. R. . Lv Boston. ............. (Regular train). ............. 2.00 p. m. Lv Worcester. ........... (Regular train). ............. 3.12 p. m. , Lv Springfield. ........... (Regular train). ............. 4.37 p. m. Dinner in Dining Car a la carte Ar Albany.. ......... .New York Central R. R.. ....... 7.45 p. m. Lv Albany .......................................... 9.00p.m. Lv Schenectady.. .................................... 9.32 p. m. Lv Utica ............................................ 11.08~.

Jan 8, 1916

By Lawrence S. Darken

STAFF: Editor, Gerhord Derge Cornegie Institute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Longenberg, R. E. Lund, W. 0. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogal. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Qusneau, A. S. Russell, R, E. Shinkoskey, W. W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L.Seigle, Chair-man, P. A. Back, J. J. Backer, l.l. Bessen, J. 0. Betterton, Jr., J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Hager, A. A. Hendrickson, M. Harmon, J. N. Hobstatter, H. H. Johnson, Jr., H. 5. Kolish, R. R. Nash, T. N. Rhodin, R. H. Richman, W. Rostokar, P. G. Shawmon, C. W. Spencer, L. Slifkin, J. K. Stanley, C. D. Starr, R. Steinitz, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; 2. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription PetroleumEngineers,$30 per year for non-AIME members in United States and North, South, and Central America; 332, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1%1 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address; AIME New York ..Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts.. .Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 4.

Jan 1, 1962

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989

Gippsland has perhaps the most colourful history of exploration of any area in Australia. Hydrocarbons were first discovered in the Gippsland Basin in 1924 when a water well at Lakes Entrance encountered oil and gas shows. In 1942, the Commonwealth and Victorian Governments, in an effort to supplement a wartime oil shortage, sank a shaft near this well and produced 8000 barrels of low gravity oil up to 1956, when the field was abandoned. A total of 64 shallow wells had been drilled in the Lakes Entrance area by that time. Elsewhere in the onshore Gippsland Basin, 30 wells were drilled from 1925 to 1941. In 1960 BHP Ltd was granted an exploration permit covering much of the offshore area of the Gippsland Basin. Esso Australia Ltd joined BHP in 1964 and drilled the Barracouta-1 gas discovery in 1965. Since then over 100 exploration and appraisal wells have been drilled in the basin resulting in the discovery to date of some 3.6 billion barrels of recoverable oil and 8.8 trillion cubic feet of recoverable gas (Current remaining recoverable reserves are 906 million barrels of oil and 5.7 TCF of gas). Exploration in the offshore areas is actively continuing today and new discoveries are still being made.

Jan 1, 1992

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970