Search Documents

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By José Vidalón

Dado que las lagunas de Papacocha y la Virreyna sufren los efectos de los drenajes ácidos de minas abandonadas, relaves y desmontes depositados en sus áreas de influencia, se ha previsto el control de los mismos. En este sentido, el presente texto evalúa los pasivos y propone soluciones dirigidas al control del drenaje ácido contaminado con metales disueltos, priorizando los métodos que no requieren la construcción y operación de una planta ni supervisión permanente.

Sep 13, 2001

By D Craw, C Smith, C Rufaut

Oceana Gold (NZ) LtdÆs, Macraes Gold Operation currently has two tailings impoundments, the larger of which covers approximately 75 ha. When an impoundment is temporarily out of use, the surface dries and dust can be blown from the surface to the surrounding area. At present water spraying is used to stabilise the surface, but this is not ideal as Macraes mine can experience water shortages during the summer. This paper examines an alternative method of surface stabilisation using vegetation as a ground cover. The tailings have a low natural fertility, so it is important to determine what will actually grow in the tailings, and whether amendments are necessary. Also important is the effect of the amendments on arsenic mobility in the tailings as the schist rock at Macraes has naturally elevated levels of arsenic. Three plants species, rye corn, barley, and lupin, were grown in metre-deep lysimeters at Macraes mine site. The plants were grown in unaltered tailings, and tailings with one of two amendments added: Bioboost (an organic fertiliser containing biosolids), and superphosphate fertiliser. The leachate from each lysimeter was collected and analysed monthly to determine the extent of arsenic mobility. In addition, laboratory experiments were set up to determine arsenic mobility in tailings with amendments at the centimetre scale.   All plants grew best with the fertiliser amendment, with rye corn growing the best overall. Plants growing in unaltered tailings either barely survived (rye corn, barley) or died (lupin). Plants in the Bioboost amended tailings grew only slightly better than in the unamended tailings. Laboratory experiments indicate that the addition of phosphate fertiliser greatly increases arsenic leaching at the centimetre scale when compared to unamended tailings. The addition of Bioboost only marginally increases arsenic leaching, compared to unamended tailings. This trend has not been repeated in the lysimeter trials on the metre scale over four months. Current results suggest that of the plant types trialed and amendments used, rye corn with superphosphate is the most practical short-term tailings stabilisation method at Macraes.

Jan 1, 2004

Develop tools that mine personnel can use to comply with 30 CFR,Part 47. Background The new MSHA rule, 30 CFR, Part 47 (also known as the HazCom rule), requires all mines to develop a written program to track hazardous chemicals at their sites. More specifically, the rule requires that mines list all chemicals and determine which are hazardous; develop a written Hazard Communication Program; label all containers used to store hazardous chemicals; obtain or develop Material Safety Data Sheets (MSDS) for all chemicals stored or produced; provide miners with training in working around hazardous chemicals; and make information about hazardous chemicals available to all workers. All mines with six or more employees must have complied with the new rule by September 23, 2002, and mines with five or fewer employees will have to be in compliance by March 21, 2003.

Mar 1, 2003

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

The Karangahake gold-silver deposit is located 11 km west of Waihi in the southern part of the Hauraki Goldfield. Historically it was the second largest bullion producer in the goldfield with a past production (1882 - 1944) of 126.712 tonnes of gold-silver bullion (Au:Ag ratio of 1:3.3) from 1 142 315 tonnes of ore grading 27.4 g/tonne gold equivalents.

Jan 1, 1987

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

Change is inevitable but learning from change is an option. Willingness to learn is one of the first lessons that a leader must learn. Get comfortable and get left behind. I propose to outline the main social changes which are taking place and their impact on the Minerals Industry. Also the changing way we do business and what are the skills needed to manage that change and diversity. How are Associations and Institutes responding to this ever changing environment? More specifically, what is my Vision for the Institute to assist professionals to achieve greater and continuing professional excellence in their chosen professions?

Jan 1, 2000

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By R. W. Nice

"The Similkameen Mining Company property is situated about 9 1/2 miles south and west of Princeton B.C. Owned and operated by Newmont Mining Corporation, mining is presently taking place in the Ingerbelle pit. At 15,000 tpd of 0.50% Cu ore the Ingerbelle pit is sufficient for about 8 years. Another 8 years ore supply is available from the old Granby workings of the Copper Mountain property which operated from 1927 to 1957.The pit operations commenced in late 1970 with the concentrator starting in March 1972. Designed and built by Bechtel Corporation under the supervision of Newmont the concentrator's design was based on single-stage crushing and single-stage modified autogenous grinding. The modification was installation of a crusher to crush the critical size build-up. The description of the operation follows.CRUSHERThe primary crusher is an open pocket Allis-Chalmers. 54"" x 74"" gyratory. The basic closed side setting is 8"". The crusher is fed from one side with 100 ton Electra-haul trucks. The crusher pocket discharges to a 96"" wide conveyor belt, then to a 48"" conveyor system including a stacker belt. The crushed product is piled on a stockpile with a capacity of about 30,000 live tons. This stockpile feeds the concentrator."

Jan 1, 1975

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Víctor Quinzano

San Juan es una de las principales provincias exportadoras de minerales en Argentina, cuya actividad minera le proporciona mayores recursos. Sin embargo, sus plantas de fabricación (molienda, trituración) producen polvos en el exterior que contaminan el medio ambiente. Por ello, los productores incorporaron nuevas tecnologías limpias que no afecten ni el desarrollo de la producción, ni el medio ambiente. En este sentido, el presente trabajo señala las aplicaciones que el Instituto de Investigaciones Mineras de la Facultad de Ingeniería de la UNSJ ha diseñado a nivel laboratorio, a través de un recuperador electrostático de polvo, el cual responde a las necesidades de los productores y cumple con el objetivo de vinculación y transferencia con el medio productivo. Asimismo, se describe el diseño de un método de recuperación de polvos y el filtro recuperador del mismo, reduciendo el nivel de polvo a un 90% y logrando un precio de venta en el mercado.

Sep 13, 2001

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By W. P. Johnstone

The computer assisted generation of geological models to represent the geometry of, and grade distribution within, orebodies is a rapidly growing area of the geological profession. Such models are increasingly used as a necessary starting point in determining the mineability of mineral deposits in terms of practical mine design and economic considerations. The transition from traditional techniques such as field or underground mapping and the manual calculation of grade and tonnage estimates, as well as related activities such as the interpolation of cross-sections, the use of stereographic projections, core logging and hand contouring, to computerized applications, is by no means complete. In fact, many geological professionals deliberately avoid the use of computer simulations based on the perception that the resulting models are simplistic and that their construction is not founded on sound geological principles. The purpose of this paper is to assess current thinking on this topic by considering; (a) an overview of advances in the drafting of geological maps, (b) the theoretical basis for multi-dimensional geological modelling, (c) the case for combining traditional and modern techniques, and (d) the benefits to the mining value chain.

Jan 1, 2003