Search Documents

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

Laboratory and pilot plant investigations aimed at recovering gold as an electroformed sheet from gold eluate and gold leach solutions and slurries are discussed. The electrolytic test work undertaken makes use of high surface area electrodes, in particular nickel-chrome foam metal and activated carbon, as well as ultrasonic activation. The process involves initial gold electrowinning (or adsorption onto activated carbon), followed by gold electroforming, both operations being carried out in a specially designed reactor. The pilot plant work mainly involved the treatment of gold eluate solutions from a South African gold mine containing 600 mg/L Au: some tests were also carried out on gold leach solutions containing 6 mg/L Au. In the former case, very efficient gold extraction onto the foam metal cathode was achieved using electrolysis combined with ultrasonics. The polarity of the gold-loaded cathode was then reversed and, using a replacement electroforming electrolyte, gold was electroformed in situ onto a polished stainless steel mandrel, from which gold sheet was subsequently removed. In the case of leach solutions, pilot plant tests confirmed laboratory findings that in the presence of calcium (resulting from the lime used during the leaching process) no electrowinning is possible. Laboratory tests showed, however, that when sodium (in the form of NaOH or Na2CO3) is added to the leach solution, electrowinning can indeed take place. Alternatively, if a special activated carbon electrode is used (without current), the non-ionic calcium aurocyanide complex is adsorbed on to the activated carbon. When a gold-loaded activated carbon electrode is made anodic in a gold electroforming electrolyte, gold electroforming is feasible, although the efficiency is very low. The possible implications of these developments for gold recovery are further examined.

Jan 1, 2007

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By Randall M. Wheeler

The measurement and analysis of blast-induced ground vibrations are more complex than ever before. This is primarily due to the advancements made in microchip technology, mass storage utilities and the computer, which have allowed us to reduce and analyze data in a matter of moments instead of days. Terminologies such as Fourier transform, response spectra, cross-correlation, convolution, deconvolution and half-length frequency, etc. mean little to anyone except those who are experts in the field. A little understanding of the basic concepts behind vibration effects can help a beleaguered end-user feel more confident about what their measurements really mean.

Jan 1, 1992

By Christoph Miller

About 80 years ago the mining industry saw an advertisement of a machine manufacturer: ?One man ? one machine?, meaning the productivity gain by using a pneumatic rock drill instead of manual tools. Mechanization in mining had started. In the 1950's and 1960's when mechanization progressed the word could be transformed into the meaning of ?one man ? one drill rig?. During the 80's automatic functions were added to the machines. Automation started. In the 90's, the first autonomous machines were seen, transforming the advertisement from the 1920's into ?one man ? multiple machines? operated from a remote control room. Soon, the productivity gain achieved by pure automation will also be flating out meaning that the margin cost of further productivity gain will be inefficiently high. What next? In mining operations there is still a high potential of unused productivity lost by ?trivial? things like organization, logistics and operational management. Changing the focus from mechanization and automation towards optimizing the overall mining process will unleash another big potential for cost cuttings and for enhancing efficiency of production. Optimizing an overall process is a task of much higher total complexity compared to an isolated machine automation focus. And a successful process integration requires the collaboration of machine vendors, infrastructure suppliers, IT services and the mine itself. It requires a number of of important preconditions to be fulfilled: ? Integrated IT systems with seamless interfaces between all components and peripherals involved ? Real time information access in all locations ? Real time overview of all operational aspects A crucial aspect for all of these issues is a seamless communication both above and also under ground and IT interfaces which are easy and price efficient to implement. This paper highlights ways to achieve productivity gains by process optimization. It also discusses needs for industry wide activities in order to enable cost efficient performance of mine process optimization projects.

Oct 1, 2009

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.

By C M. Evans, D Thomas

Solid EnergyÆs Wangaloa open cast coal mine was operated between 1945 - 1989, and remained closed and disused until 2001 when SENZ initiated a mine rehabilitation programme. It is nearing the final stages of physical and environmental rehabilitation, aimed at creating an aesthetically pleasing and useful landscape. The final goals of these efforts are to produce an area, which has recreational and educational value. SENZÆs holistic approach to rehabilitation has been undertaken, treating the entire historical mine footprint instead of focusing only on those disturbed areas and the minimum range of issues just to meet with legal compliance. Rehabilitation at the site has included overburden modification with an emphasis on stability, removal and replacement of unhealthy and invasive plant species, and an AgLime amendment to alter soil pH conditions, which would support native plant species. To date, most ongoing activities relate to final planting and plant upkeep, and maintenance of the landform including ongoing erosion control, pest control, environmental monitoring, and research. Environmental quality concerns at the site may be treated by using a combination of methods, including regrading and capping of acid-generating pyrites, soil treatment with AgLime, and passive wetland treatment within existing water courses. Following major works, the mine site area may be opened to the public for recreational activities, interpretive displays on historical mining activities, and observation and appreciation for otherwise unseen geological features. SENZÆs holistic approach to reclamation, rather than treating minor issues, will result in the former mine site being transformed into an asset and the environmental and financial liability associated with the closed mine being discharged. Former mine sites can be turned from environmental liabilities with no recreational or public value (and potentially dangerous to life) into sites that can be safely used by the public for recreational and educational purposes.

Jan 1, 2006

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012