Search Documents

Jan 1, 1962

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

One of the most important parameters in mine ventilation planning is the friction factor (K). Accurate values of friction factors are critical especially when carrying out mine ventilation simulations. No computer simulation of a mine ventilation network is meaningful if the airway resistances are not accurately estimated (when planning a new mine) or measured (for an existing mine). However, in the first case not many reliable values of friction factors exist in the international literature. This paper presents the results of a research project carried out in the province of Quebec where ventilation friction factors were measured in all underground metal mines. These friction factors are statistically analyzed and tabulated. A friction factor database was created that also includes the friction factors measured in the past by other people. This database can help the mine engineer to accurately estimate ventilation friction factors according to the specific conditions. This database offers several values of friction factors typical for hard rock mine conditions typical of modern underground metal mines.

Jan 1, 2009

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By J. Chirasha

Keywords: Pyrometallurgy, ferrochrome, smelting, investment, Zimbabwe Four smelting plants currently make up the ferrochrome smelting capacity in Zimbabwe. Zimbabwe Alloys and Zimasco represent more then ninety per cent of Zimbabwe?s ferrochrome smelting capacity, while Maranatha and Oliken contribute the difference. Very limited investment in the sector (even for the expansion of existing smelters) has been experienced over many years, despite the fact that about 95% of the world?s chrome ore resources are in the Bushveld Igneous Complex of South Africa and the Great Dyke of Zimbabwe. The Bushveld has a greater quantity but a lower grade than the Great Dyke. A ten per cent increase in Zimbabwean ferrochromium production has been recorded in the past ten years, showing an almost stagnant capacity investment.

Jan 1, 2011

By Christoph Mueller

Mining operations today are characterized by a high degree of mechanization and single machine automation. However, their potential for cost cuttings and increase of productivity in the future is quite limited. Enabled by newest IT and networking technology, the operation of underground mines more and more can be seen from a process related point of view: Standardized Ethernet and Wireless LAN are the basis for a seamless and unified communication backbones providing an integrated infrastructure for data, telephony and video. All the components are available as off-the-shelf devices leading to an excellent cost efficiency. Basing on this standardized infrastructure, the equipment is able to become part of the infrastructure. To enable machines to be integrated smoothly into IT networks, the machine also has to have enhanced networking capabilities. This results in a new system architecture for the on board machine electronics separating real time control from IT and networking level functionality which can be implemented by a Machine Server. This machine server communicates with all kinds of above ground systems using mainly standardized formats like html or the IREDES standard. This information is made available mainly in 3D mine visualization tools. The paper explains this technology and shows implementations by two working examples.

May 1, 2006

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 239 to 245. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropriateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at30th June, 1997, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1997

In understanding the consequence of existing law, and the likely implications of its reform, it is necessary to comprehend the logic of the situation that the law provides individual decision makers and how that situation would be adjusted by reform. In particular, the way in which natural resources, including minerals, are used and managed is influenced by the definition and structure of property rights that the law provides. Property rights are enforceable claims to use or to benefit from resources. An example is a mining licence that allows its holder to extract minerals in a specified area. Property rights establish the structure of incentives, opportunities and constraints within which resource use decisions are made, ie the logic of the situation, and hence influence the use and management of resources. The extent and type of mining in New Zealand, for example, reflects the rights that miners have to extract minerals, and their rights to benefit from mining as against their duties to compensate landowners and pay royalties. This paper describes the characteristics of minerals that are relevant to the definition of property rights, analyses the implications of alternative property right arrangements and describes the existing situation.

Jan 1, 1988