Search Documents

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

Many of the world?s largest existing mines are considering substantial step changes in production volumes, compensating for declining ore grades while trying to address increases in world demand for resources. The natural configuration of coal deposits allows for many mine development openings along the strike to access the ore body and thus increase volume. Similarly, with iron ore the nature of the deposits means that additional capacity can easily be added by opening up new mesas and providing extensions to infrastructure. On the other hand most of the non-ferrous metaliferous deposits form vertically and additional extraction volume comes from increasing depth. Underground mining from the base of the strata allows for large extraction rates, but block or panel caving operations develop at rates dictated by the geophysics of the overlying strata and the need for massive tunnelling developments to establish sufficient extraction points for high volumes. For really big mine production capacity, open cast mining still allows the easiest development of more massive mining techniques. But there remains the question of whether there are limits to how large an open cut mine can become in terms of throughput?

Feb 27, 2013

By D. Bogunovic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices, and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents a result of research work on development of an integrated data environment system for analysis and control of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where, and how much energy is being used. This developed system represents a framework for efficient management of energy consumption. Key words: surface mining, coal, energy consumption, Information System.

Jan 1, 2009

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By Sangseom Jeong, Kyoungyul Kim, Jaeyeon Cho

"Abstract The lateral earth pressure of vertical circular shaft is investigated by using experimental tests and a theoretical analysis. The emphasis was quantifying on the magnitude and distribution of a lateral earth pressure measured by three-dimensional arching effect. A framework for determining the earth pressure distribution on the basis of both centrifuge model and full-scale field test results is introduced. Through these studies, it is found that the lateral earth pressure decreases within active displacement (dh/H: 0.2×10-2, dh: horizontal displacement, H: Height of vertical shaft) of wall at deep excavation and the arching effect is more significant for deep excavation than for shallow excavation. It is also found that the lateral earth pressure acting on a vertical circular shaft considering arching effect is 70% smaller than that calculated by Rankine theory, and thus represents a significant improvement in the prediction of realistic earth pressure for vertical circular shaft subjected to arching pressure.INTRODUCTIONIn South Korea, an increasing need for underground excavation and the application of the vertical circular wall (i.e. vertical shaft) is becoming an important issue in engineering practice. Here the vertical circular wall is generally embedded in soft or hard rocks through weathered soil varying thicknesses ranging up to 15 m. Since 1980, a number of huge excavation projects such as underground space for constructing power stations, subways, high-speed railways, and many lifeline constructions have been performed in urban areas (Jeong and Seo, 2004). Although there have been considerable advancements in construction techniques involving vertical circular wall, it is still very important for tunnel engineers to control the lateral earth pressure. Additionally, Proper estimation of earth pressures is a key factor in design of vertical circular wall. Because of three dimensional arching effects, i.e. convex arching and/or inverted arching, the earth pressure acting on a circular type of wall is less than other types. Thus, the vertical circular wall is generally used."

Jan 1, 2014

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By Chris Breeds, Ken Johnston, Omar Fulton

This paper describes the process typically involved with obtaining permits for quarry blasting in urban, suburban, and rural areas, including: content of SEPA (State Environmental Policy Act) driven documentation; regulatory review and comment; public interaction; public hearing(s); periodic regulatory review(s); negotiated solutions; monitoring; and the role of public interaction, demonstration(s), and education in the process. Case studies will be presented of projects undertaken in the State of Washington that illustrate the approach and regulatory interaction as well as the importance of public interaction throughout the process. Reference will be made to the role of national and state regulations and local codes and ordinances that provide additional limitations on blasting practice. The paper will also present regional blast monitoring data that are used in the permitting process and the layout and design of blast monitoring systems typically required as conditions of the quarrying permit. Our presentation will include tools, which we have developed to assist with explaining blast related phenomenon to both regulators and the public.

Jan 1, 2003

The recent paper by Bain (1981) contains an unfortunate, and potentially misleading typographic error. On page 9, second paragraph, Bain states that, "some samples of drill core from the (Candlow) Formation ... contain up to 90 ppm gold and 2 000 ppm arsenic". The gold value should read 90 ppb. In fact, in the original version of the paper (Bain, 1980), the gold value quoted was actually 60 ppb.Bain also refers briefly to some geochemical data which is attributed to me, and which I feel require some clarification.In addition, the paper contains some factual errors relating to the occurrence of carbonate and potential host rocks to Carlin-type gold deposits in the Candlow Formation.

Jan 1, 1981

By Nils Heinke, Stephen M. Collinsorth

To anyone who is responsible for the production of blast holes, who is looked to on a daily basis for drill maintenance and performance, whose bottom line may depend on the survival of the mine itself.. How much awareness should one have on such things that truly impact production, maintenance and overall job cost? Do you know your drill’s maximum capacity?

Jan 1, 1998

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By T F. McConachy, B I. A McInnes, R A. Binns

Within the last decade, major research discoveries have been made in the submarine realm of magmatic and hydrothermal activity of arc-backarc systems in the southwestern Pacific. These include identification of numerous particulate-poor, gas-rich (CO2-CH4) hydrothermal plumes emanating from arc front volcanoes, actively forming porphyry-copper-gold style mineralisation, and new backarc spreading systems erupting alkali basalt-trachyandesite magmas. Major goals of these studies have been identification of modern analogs to ancient volcanogenic massive sulfide ore bodies, and quantification of the volatile fluxes though supra-subduction zone systems.

Jan 1, 2002

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.