Search Documents

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By M. J. Nicol

The kinetics of the dissolution of colloidal silver in aerated cyanide solutions has been investigated with the aim of developing a relatively rapid and convenient method for monitoring the ?leaching power? of solutions typically used in the cyanidation process. Experimental results obtained are consistent with an electro-chemical model, in which the mixed potential is set up in the active region of the polarization curve for the anodic dissolution of silver, giving rise to a rate of dissolution which is controlled by the rate of mass transport of either cyanide or oxygen to the surface of the silver. The rate of dissolution of colloidal silver was found to respond to variations in the reactant concentrations in a similar manner to gold (and silver) in a typical free-milling ore. The use of this technique for the monitoring and control of the cyanide leach process is discussed.

Jan 1, 1998

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001

By R. N. Tempel, M. Lengke

Arsenic sulfide [orpiment, realgar, amorphous AsS and As2S3] oxidation rates were measured in mixed flow reactors at pH~2 and temperature of 25-30oC. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2 s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH~2 from amorphous AsS > realgar > orpiment > amorphous As2S3. In comparison to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH~2.

Jan 1, 2002

By W. Pulles

Mining can adversely affect water quality and poses a significant risk to South Africa?s water resources. Proactive management of environmental impacts is required from the outset of mining activities in order to reduce this risk. Major strides have been made over the last 7 to 8 years, by both the Department of Water Affairs & Forestry (DWAF) and the mining industry, in developing strategies and management plans for the effective management of water within the industry. This has largely been achieved through the development of joint structures where problems have been discussed and addressed through cooperation. This process, which was started around 1991, has continued through to the present time. The mining sector management strategy has been developed at a number of different levels as follows: ?A detailed Management Plan, that sets out strategic objectives, broad strategies and functional and organizational arrangements. ?Operational Guidelines, that define and document specific operational procedures. ?Technical Guidelines, that define and document best practices for pollution prevention and impact minimization from mining operations. The Technical Guidelines consist of Best Practice Guidelines (BPGs) and Regulations.

Jan 1, 1999

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By Bengt H. Fellenius

"ABSTRACTAn example from a guidelines document for the Eurocode is discussed that addresses design for geotechnical strength of piled foundations in settling soil, generating drag force and downdrag. A modified example of geotechnical response is then analyzed in a failure mode, Ultimate Limit States (ULS), and stationary long-term state, Serviceable Limit States (SLS). It is shown that the Eurocode principles, when applied to correctly determined forces, results in an irrational and costly design. The results of the analysis of the modified example are applied to eight different codes pertaining to piled foundations from USA, Canada, Europe, and other countries. Several of the codes require that the drag force be included as a load in a ULS design, which an absurd and costly requirement, in some codes, in one case made even worse by combining drag force with live load. A major weakness of almost all codes is their minimal treatment and sometimes total absence of aspects of settlement of piled foundation. In contrast, my main argument is that design for capacity, whether in working stress approach, or by LFRD or ULS approaches, is not always safe unless a thorough settlement analysis shows that the design also meets the requirements of the SLS.1. INTRODUCTIONFirst, there were analysis, design, and construction establishing a State-of-Practice, SOP. Then, came codes and specifications summarizing the SOP, as interpreted by a committee. When the state-of-art, SOA, was not understood by that SOP-interpreting committee, the codes and specifications are uneconomical and, sometimes, also unsafe.The paper first presents an example quoted from two commentaries on the Eurocode 7 on design for geotechnical strength by the Eurocode (1997). The example is then modified to a more realistic case and analyzed in failure mode (ultimate limit states, ULS) and in the context of settlement (serviceability limit states, SLS). The analysis results are then applied to eight codes addressing piled foundation design and changes necessary for the referenced codes and specifications to be closer to the SOA are identified."

Jan 1, 2014

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By Steve Kral

Amax Coal Industries Inc.&apos;s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state&apos;s oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

By Carl W. Lam

The increased obsolescence rate of electronic products has made it evermore pertinent to understand the potential environmental impact of materials choices to help guide electronic waste (e-waste) management and promote awareness of high burden materials. Methods for screening for the performance of materials and their potential burden on human health and the environment can be used to comparatively select constituents of present and prospective electronic products. These methods should be able to yield more robust information when linked to other decision-making strategies where integrated data on consumer preferences, production quantities, and regulatory initiatives are sparse or unavailable. A framework is presented here for generating metrics of ecological toxicity, human health toxicity (cancer and non-cancer categories) and global resource consumption for evaluating environmental impact of materials (specifically metals) in electronic products. The time-dependent impact trends of United States? printed wiring board (PWB) metals usage, principally derive

Jan 1, 2010

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President&apos;s 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976