Search Documents

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

By Valentin Choquenaha Bombilla, Oscar Alvarez Muiloz

"Tintaya’s basic production line is copper concentrate, which has an important gold content. The process used is flotation; the objective of the metallurgical department is to obtain the best results in the copper recovery without neglecting the gold, using very specific reagents. Copper recoveries are considered high, nevertheless every day emphasis is placed upon increasing those recoveries. Regarding gold, optimum recoveries could not be achieved with flotation; and implementation of a gravity circuit was considered.According to microscopy studies, the coarse and very fine grains of gold in native form are lost to tails. The native gold due to its high specific gravity is concentrated at the underflow of the cyclone, remaining in the circulating load of the circuit. It reaches three times the concentration compared to the head grade entering the ball mills. This re-circulation generates very fine and laminated gold particles inside the ball mill, passing to the classification stage making a short circuit to the overflow of the cyclone.The very coarse gold particles as well as the thick flakes of gold do not react favorably to the conventional flotation process; thus studies that have included gravity separation have been conducted to increase the gold recovery. Part of the research included concentrating tables, jigs, and Knelson Concentrators. The Knelson Concentrator proved to be the best selection in terms of metallurgical performance and recoveries considering the throughput and operation conditions of the Tintaya Plant.The gravity concentration circuit with the Knelson Concentrator was commissioned in BHP Tintaya in October 1998, as per the flowsheet shown later on. Presently the global gold production surpasses any estimated expectations.Present efforts are directed towards showing the evaluation and optimization of the different parameters that govern the performance of the Knelson concentrator, as well as illustrating the difficulties and successes throughout the operating period.In the first year of operation 200 tons of gold concentrate have been produced with an average concentrate grade of 320 gramdton, having paid back in full the cost of the automated KC-XD- 48 Knelson Concentrator, the peripheral equipment, and the cost of the installation."

Jan 1, 2002

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a “stand up” or “box cut” mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of Orica’s knowledge of blast design, modelling and i-konTM electronic detonators.

Jan 1, 2003

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By N E. Whitehead

An application to mine an ilmenite-rich sand deposit in Westland led to public concern about potential radioactive hazards should the ore be further processed to recover zircon or monazite. A review recommended that any material involved in the heavy mineral sand industry containing more than 0.05% thorium, uranium or their mixture should be considered a radioactive substance and, for mining purposes, a notifiable product. Safeguards for those occupationally exposed would operate via the Radiation Protection Regulations. The major safety requirement would be the minimisation of dust in certain operations.

Jan 1, 1993

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By Changping Hu, Keqin Tan

In 1937, the Metallurgical Department of the National Resources Committee established a copper refinery plant (predecessor of the Chongqing Smelter) in Changsha, Hunan Province, China. The blister copper produced by a local copper smelter was casted as anode for electrorefining. The plant, with a capacity of one ton of electrolytic copper per day, was designed and tested in 1937. At the trial production stage, a total of 9 tons of cathode copper was produced. The plant was formally put into operation in July 1938. In the same month, more than 20 tons of electrolytic copper with purity over 99.9%Cu was produced. This was the first batch of electrolytic copper produced in China. In 1939, China’s largest non-ferrous metal smelting plant, Fengtian Gold Mine Refining (predecessor of the Shenyang smelter) was completed and put into operation in Shenyang, mainly producing nonferrous metals such as gold and silver, as well as copper and lead. In 1939, the Kunming copper smelter (predecessor of Yunnan Smelter) was completed and put into operation. The plant equipment, imported from the United Kingdom, was designed to produce 1,200 tons of electrolytic copper annually. In 1943, Jiatong smelter (predecessor of the Shanghai Smelter) became the 4th domestic cathode copper producer. Since 1949, China has gradually established a large copper industry. These developments are discussed in this paper. Today, China operates nine out of the twenty largest copper refineries in the world. With a total capacity approaching 9 million tons of copper per year, China has the world’s largest copper refining capacity. INTRODUCTION China is a country with a long history of copper mining. The earliest smelter in China in recent times was the Shanghai Smelter, which was built in 1912. From then until 1949, China successively built Chongqing Smelter, Kunming Smelter and Shenyang Smelter. The world's first copper electrorefinery was the Pembrey refinery built in the UK in 1869 (Lu, 1999). However, it was not until 69 years later that the technology was spread to Changsha, China.

Jan 1, 2019

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

Comparison of Industrial Cyanide Destruction Processes

Sep 13, 2010

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

No blast evaluation is complete without fragmentation measurements which until now were inaccurate, costly, time consuming and created delays in production. “WipFrag.s”is a fully automated PC based fragmentation analysis system that uses digital photo analysis techniques to measure broken rock. Fragmentation can be measured in minutes using compact videocameras for image acquisition. Even subtle changes in rack quality can be detected providing the information necessary for pattern optimization, explosives evaluation, timing selection, benchmarking and blast model validation.

Jan 1, 1995