Search Documents

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an' type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fixed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user:- to develop a technical model for conceptualised conveyor systems,- to perform economic analysis on the developed technical model, and - to conduct a comparative and risk analysis.An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help files as well as the use of familiar graphical user interface elements such as the MS Office 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

By C. L. Reichardt

Mining companies are increasingly looking to the developing world for the next generation of mining projects, often in countries that have little or no previous history of large-scale mining. One of the major challenges for such projects is hiring?and retaining?personnel that have technical skills and experience in mining-related disciplines. Staffing a mine with an expatriate workforce is neither cost-effective nor sustainable, and many countries now insist that mining companies ?transform? the profile of their workforce to more closely mirror the demographic profile of the host population. The need to nurture mining-related skills in emerging mining nations is not solely limited to the workforce: there are also pressing economic and sustainability imperatives to develop capacity within local service providers such as consultants and contractors, as well as to facilitate informed engagement between mining companies, government and civil society. However, few educational institutions in emerging mining nations currently have the ability to offer practical training in mining-related disciplines. Local employees who are sponsored by companies to develop their skills through international study maybe impeded by language and cultural barriers, and may also be taught using course content that is of limited relevance to the specific challenges of their future working environment. This paper addresses the challenge of skills development and retention in emerging mining nations and uses examples from sub-Saharan Africa and the Asia Pacific region to explore practical means of developing capacity in mining-related disciplines. It examines the need for companies to implement strategies to develop local technical capacity in countries where they envisage a long-term operational future and also highlights the need to foster partnerships between academia, developmental institutions, mining companies, governments and civil society to establish the critical mass of mining-related skills required to nurture the development of a sustainable mining industry.

Jan 1, 2009

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By Ravichandar. D., K. B. Nagashanmugam, M. S. Pillai

"Blast furnace performance depends strongly on the coke reactivity index(CRI) and coke strength after reaction (CSR) properties. An innovative and cost-effective method, known as the Salem Box Test, has been developed to prevent the mass production of inferior coke unsuitable for blast furnace use. This method consists of coal carbonization on a micro-scale and involves charging approximately 18 kg of coal blend in a stainless steel box, carbonizing it together with coal cake in the plant coke ovens, and testing the coke produced for CRI and CSR to determine its suitability for blast furnace use. Only coal blends that yield coke with CRI <25% and CSR >64% are permitted for mass production, and other coal blends are either rejected or the blending ratios adjusted in an attempt to upgrade them. The experimental results reveal that, for a given coal blend, the quality of coke produced by the Salem Box Test is comparable with that produced by bulk production, indicating that the test is acceptable as a screening tool for regular use. The present paper describes the methodology and application of Salem Box Test to predict the suitability of coke for blast furnace use at JSW Steel Limited, Salem Works (JSWSL), and illustrates its advantages in adjusting the coal blending ratio to produce superior coke, in detecting coal contamination, and in preventing bulk production of inferior coke."

Jan 1, 2015

By J. D. Doll

MSHA has promulgated a rule to limit the exposure of underground metal/nonmetal miners to diesel particulate matter (DPM). In May 2008, the final personal exposure limit will be lowered to 160 µg/m3 total carbon. To comply with this rule, mine operators are implementing a variety of control technologies. In this study two types of control technologies (ventilation and cabs) which are being implemented in limestone mines were investigated. Two stone mines in this study use large diameter propeller fans for main mine ventilation and direct the air to the faces using auxiliary fans, stoppings, and long pillars while bypassing the old mine workings. NIOSH measured for sub-micrometer elemental carbon (EC) using SKC DPM cassettes (analyzed using NIOSH 5040) and a near real time instrument. With the present ventilation and the number and type of vehicles used, the concentration of EC from DPM at the working areas was at or below 400 µg/m3 for both mines and about 166 µg/m3 and 251 µg/m3 at the returns. The real time data showed that the ventilation was reaching the working areas and effectively diluting the DPM. Environmental cabs were also used to reduce DPM exposures in three underground limestone mines. Using NIOSH method 5040 and near real time EC instrumentation, NIOSH sampled inside and outside of a loader cab at one of these limestone mines to determine the effectiveness of the cab. The cab was found to be over 90% effective in removing DPM as long as the cab system was properly maintained, and doors and windows were closed.

Jan 1, 2009

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40&#176;C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25&#176;C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40&#176;C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes&apos; new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

By D. A. Stanley

The Bureau of Mines conducted laboratory-scale experiments to determine whether or not surface waters with a high organic content could be purified sufficiently to be used to replace the natural high-quality deep well water currently being used in the silica flotation step of phosphate rock beneficiation. Waters abundant in organic matter were collected from two central Florida streams, flocculated with a cationic polyethylenimine polymer, and processed in a sand filter. This treatment removed most of the organic materials from the water. Untreated surface water, treated surface water, and distilled water were used to compare the flotation response of the acid insolubles in an amine flotation circuit. Surface water treated with PEI-1000 was shown to be as effective as distilled water for the acid-insoluble-flotation step. Flocculation and filtration can therefore produce water suitable for amine flotation of quartz, which would permit substitution of surface water for deep well water.

Jan 1, 1981

By M. Hopf

The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However, even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able consistently to identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed).Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa. Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway

Jan 1, 2006

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner&apos;s performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983