Search Documents

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By W. T. Wertman

A research program to aid development of better and more efficient methods for producing petroleum and increasing its ultimate recovery from underground formations is an integral part of the work of the Bureau of Mines on conservation of the Nation's natural resources. Economic, efficient production of recoverable oil and gas from a reservoir depends to a great extent upon the best and most accurate information that can be obtained from a study of the reservoir rock and its fluid contents. Information on oil and water saturation is pertinent and essential in wildcat, extension, and pool wells for good reservoir operations and prediction of performance. This report presents results of an investigation by the Bureau of Mines of core recovery and degree of drilling-fluid contamination occurring during cable-tool coring operations using oil-base mud. Representative core samples were obtained from 6 major oil-producing sands in 8 fields of West Virginia, Pennsylvania, and New York. Field-mixed, oil-base drilling mud was used for the first coring test, and lightweight, premixed oil-base mud, with an organic chloride tracer added, was used in coring eight other wells. Tracer analyses were made to determine contamination of core by drilling-fluid filtrate. Core analyses, including oil and water content and minimum interstitial water-saturation tests, were made on selected core samples to compare and evaluate water saturations determined by the two methods.

Jan 1, 1958

By Eduardo Nunez, Asim Tuzun, Dan Graffi, Glenn MacPherson

"In preparation for the milling of a new nickel and copper mine ore, Nickel Rim South, Xstrata’s Strathcona Mill is undertaking numerous process improvement projects. Within the grinding circuit, several projects are under development and an automated grinding control strategy, consistent with the operating objectives, was identified as a key requirement. The grinding strategy is to maximize the throughput (quantitative objective) while maintaining the cyclone overflow within specifications (qualitative objective).This paper describes the implementation of a robust grinding control strategy using the existing control system. The implemented controls maintain the cyclone overflow density at the desired target, while continually optimising the rod mill feed rate to allow maximum throughput. This approach has the added benefit of improving the stability of the rougher flotation circuit down stream of the grinding and improving energy efficiency of the rod and primary ball mills. This paper discusses the comparison of the before and after the implementation of results.INTRODUCTIONThe grinding process is a size reduction operation used in the mining industry to liberate the valuable minerals from the gangue. Grinding is one of the most important and expensive processes in a concentrator (Xi-song, 2007; Pomerleau 2000; Najim 1995), often accounting for around half of the total operating costs in base metal concentrators (Wills, 1990), which has led to a focus on development and implementation of control and optimisation strategies. The grinding process prepares the ore for the subsequent concentration step, which for sulphide base metal operations, is predominantly flotation. The performance of the concentration (flotation) is very much determined by the feed characteristics of the slurry coming from grinding. The valuable minerals recovery process in flotation is very much influenced by the grinding process and the liberation of the desired minerals from the gangue minerals (McIvor, 1991).The true objective of grinding is to obtain a proper liberation of the minerals as defined by a particle size distribution referenced typically by d80 (80% passing size of product). Besides achieving the desired mineral d80 size, it is clearly desirable to produce as narrow a size distribution as possible to squeeze the maximum amount of the mineral value into the highest recovery region (McIvor, 1991). This is an important criterion for the mill in economically optimizing the grade and recovery for the concentrate product. It is important not to over or under grind, while keeping the specific comminution energy as low as possible (Nunez, 2005) to achieve the target liberation. In other words, maintain an optimal throughput depending on the ore conditions to the capacity of the grinding mills, while providing the flotation process with a constant and narrow size distribution, at a cut size selected to meet the metallurgical requirements (Bascur, 1991)."

Jan 1, 2009

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By D. Linzey

"History of Whitehorse Copper BeltThe first discovery of copper on the Whitehorse Copper Belt is reported to have been made by miners on their way to the Klondike in 1897. By 1899 the district had been well prospected and many of the presently known deposits had been staked.The first shipment of ore was from the Copper King property in 1900. This consisted of 9 tons of hand picked ore grading 46.4% copper. It was not until the period between 1912 and 1917, the production years of the Pueblo Mine, that significant ore shipments were made. Total production was 140,000 tons at 3.5% copper. An underground disaster killed six men and closed the mine in March 1917.Although the general area was dormant until after World War II, by 1947 geological mapping, magnetic surveys and diamond drilling had been done on the important showings. In 1954 Mr. Aubrey Simmonds directed the formation of Imperial Mines and Metals, which acquired by option and staking a large part of the Whitehorse Copper Belt. In 1957 Mr. Arnold Pitt reorganized the company as New Imperial Mines. With financing from Sumitomo and Toronto-Dominion Bank, a mill was built and production was started from the Little chief orebody by open pit in 1967."

Jan 1, 1977

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By Julver Álvarez

El presente trabajo describe el comportamiento estructural y mineralización del estaño-cobre en la mina San Rafael, Puno. En este sentido, las pizarras de la formación Sandia del Ordovisco Superior, por metamorfismo de contacto con el intrusivo, han sido transformadas a hornfels, que junto a las cuarcitas se presentan algunas veces como una cubierta superficial sobre el intrusivo. Asimismo, los intrusivos y las pizarras son favorables para la mineralización de estaño, aunque los cuerpos del mineral son más definidos y persistentes en el intrusivo.

Sep 13, 2001

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of tie California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984