Search Documents

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001

These proceedings consist of an introduction and four descriptive papers. The first paper is an update on fire protection for large haulage vehicles, the second paper is concerned with improved visibility systems for large haul- age vehicles, the third paper is on improved ladders for large haulage vehicles, and the fourth paper is concerned with large haul-age vehicle operator training systems.

Jan 1, 1980

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

Conventional waste management practices produce two waste streams for the construction of separate disposal facilities. The design of tailings impoundments is usually controlled by physical stability. Waste rock materials offer high shear strength characteristics for waste dump construction, however the hydraulic properties promote oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. Co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retention capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimize acid generation and metal leaching. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repository. The results of a laboratory program to characterize the physical and hydraulic properties of Comix tailings and waste rock are presented here. Various ratios of tailings were blended with three distinct waste rock materials. The saturated hydraulic conductivity for the Co-mixed materials was found to vary between 2 x 10-7 m/s and 5 x 10-8 m/s depending on blend ratio, waste rock type and compaction. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the hydraulic behaviour of a Co-Mix waste system. The potential benefits of Co-Mix are shown for a typical mine.

Nov 1, 2002

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha

Knowledge of fuel qualities is of ultimate importance for the efficiency of chemical plants or power stations. Although most blending yards are equipped with automatic samplers and the derived samples are processed in the laboratory, the quality variation of the blended product may still be strong. This is caused by several reasons. First of all the process of sampling, crushing, dividing and analysis is time consuming. Results are available only with a delay of two to 24 hours. During this time blending is operated without knowledge of the main parameters. Conveyors with high throughput require expensive sampling systems capable of handling samples which are representative. The frequency of sampling needs also to be high in order to be representative. This results in high maintenance costs and also downtime of the sampling system.Online analysis of bulk materials has matured over time and today it can supplement but not replace laboratory analysis. As an example, J&C Bachmann has realised a coal quality monitoring system on the coal supply of a South African coal processing plant. The plant consumes ~42 Mt of coal per annum. The blending yard consists of two sets of three heaps where coal of six different mines is blended according to the factory’s requirement. From there, the blended coal is fed to the factory on two different belts.In 2010 the plant installed a TEXAS X-ray fluorescence analyser as a trial. It was tested under different conditions on several belts before the customer decided to install six TEXAS analysers on the feed belts to the stackers and two more analysers on the reclaimer belts. All analysers are installed directly on the belt and not on a substream.During the test period blending strategies were developed in close cooperation between the customer and J&C Bachmann. The use of the analysers in conjunction with the blending model has proven that the variation of the reclaimed coal quality was decreased significantly, which results in increased process performance and significant cost savings.CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P and Ha, J, 2017. Online quality control of a coal blending yard, in Proceedings Eighth World Conference on Sampling and Blending , pp 125–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By Thomas Z. Jones

Deep mining within the Sewell Coal member of the New River Formation in southern West Virginia has exposed several small-scale thrust faults and related features. The faults were en- countered in Westmoreland Coal Company&apos;s Eccles No. 6 Mine located near Beckley, West Virginia (Figure 1). The purpose of this paper is to: 1) describe the nature of these faults and the effect they have on mining, 2) discuss the roof support methods used in the fault zones, 3) establish a mechanism for the origin of the faults. and 4) demonstrate how the mechanism was used to forecast fault trends across the mine property.

Jan 1, 1986

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Joey Hoang, Robert Johansson, Tapani Keronen, Mikael Jåfs, Jani Jansson, Mikko Korpi

At the Copper 2016 conference in Kobe, Japan, Outotec introduced a vision for the year 2020, wherein smelting would make use of four digital cornerstones: intelligent instruments, advanced process control, improved information management and transparency of and access to data. Since then, this vision coined the phrase “Fully Automated Smelter” with the mission promising a concept where no manual actions from human operators would be needed during normal smelter operations. Replacing repetitive physical work, collection and analysis of everyday production data has a great potential for further automation and will provide productive ways to improve efficiency and safety of smelters in the future. Therefore, a lot of emphasis has been put into developing solutions to automate these tasks and to move people out of harm’s way. A lot of new equipment, systems and optimization tools are under development. In addition, a lot of effort is going into developing dynamic process models and advanced control systems to interface with the plant automation systems. The goal is to integrate all these concepts to meet Outotec’s Fully Automated Smelter vision. This paper will cover these latest achievements toward this vision and introduce the near-future of digital smelting. INTRODUCTION As is well known already, the humankind is currently experiencing a change, extent of which is broadly studied by the governmental, educational and industrial institutions and parties. The wellbeing and quality of life have traditionally been improved alongside the developments in industrial production, which is now about to enter its fourth revolution. Therefore, the current change is often described as fourth industrial revolution, or industry 4.0 (or industrie 4.0, as named by Acatech, 2013) and can be considered anything from small incremental development to a ground-breaking global reset that will affect everyone’s lives. Many seem to agree, that the scale of change will indeed be big, even significantly bigger than the three industrial revolutions before it (Pellini, Weyrauch, Malho & Carden, 2019; Geissbauer, Vedso & Schrauf, 2016; Jansson, Bjorklund, Lahtinen, Heinonen, Jafs & Fagerlund, 2016).

Jan 1, 2019

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By G. Smith

This paper describes the allure of diamonds over time and highlights the magic and mystery of famous diamonds. Consideration is given to the effectiveness of marketing in the diamond industry. It is concluded that diamonds are held as cherished possessions, valued far above their real market price, retained as valued heirlooms, and widely used as a form of highly liquid currency. In order to sustain value, both from an investment and jewellery perspective, demand has been stimulated to keep pace with growing global supply while the illusion that ?diamonds are forever? has been fostered to ensure that most diamonds, once sold, do not re-enter the market.

Jan 1, 2003

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By Bill Mercer

The Triggers for PDAC Involvement in H&S ??Increase in serious accidents in mineral exploration in past few years ??Increasing junior role in exploration ?? Impression that there were few H&S protocols in place in smaller companies ??Lack of national benchmarking ?? The attitude that H&S is a provincial responsibility ??Corporate Social Responsibility initiative What is the issue in exploration? ??Mining?s reputation as ?dirty and dangerous? ??In public?s and media?s minds exploration employees are ?miners? ??In Canada, regulators often do not distinguish between ?exploration? and ?mining?. ??How does exploration compare to mining from a H&S point of view?

May 1, 2008

By T Hirsi, M Weatherseed, T Ritasalo

Cooling tower design has not advanced significantly in the last decade. Recognising this, Outotec has developed an innovative horizontal outflow cooling tower with increased performance compared to conventional design cooling towers.Outotec&#174; Cooling Towers operate today in applications such as spent electrolyte cooling in zinc plants and for gypsum removal before copper solvent extraction. In such applications the use of this latest design has enabled increased production and lower maintenance costs in the downstream operations.In actual operations, the cooling performance has been confirmed at start-up, and has demonstrated that the towers operate in accordance with the CFD modelling. In the last three years these towers have proven themselves in commercial operation to operate with high efficiency and availability.This case study will outline comparative data, collected over two years at a site where both Outotec and conventional cooling towers are operating. The data shows that Outotec cooling towers require less than half the maintenance time of conventional cooling towers, when adjusted to a total solution flow basis. A close partnership approach with the site has allowed continual development, ensuring high availability and high performance.Experience with previous cooling tower installations guided the development of maintenance philosophies and procedures; this resulted in a design where maintenance intensive components were accessible from the top of the cooling tower. This allows safe access to components and maintenance with little or no downtime.CITATION:Hirsi, T, Ritasalo, T and Weatherseed, M, 2015. Improving cooling tower performance with innovative horizontal outflow design, in Proceedings MetPlant 2015, pp 396–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M. S. Borges

The need for the waste management industry to reach environmental patterns, technological innovation, and a technological demand of the productive sector is covered by this study. The environmental care and responsibility in the industrial sector and the necessary cultural changes for companies and entities is also emphasized. A collaborative tool was developed to help all partners involved in the environmental administration. This tool focuses on the interaction among residue generators in the productive chain. It was developed for a vehicle assembler company supported by entities or institutions with emphasis in the research, development and innovation, with expertise and capacity for new products creation, as well as reuse, recycling and reduction of by-products generation. The work aims to establish a tool for socio-environmental management, focusing on promotion and interaction between industrial waste generators sectors.

Jan 1, 2010

By Leslie S. Rubin

A ventilated helical boost pump was developed that can handle varying flow rates and/or solids concentrations while operating at a single rotational speed and without computer assisted feedback controls. The boost pump developed and briefly tested during this program was designed to accomodate flows suitable for a 3-in. diameter pipeline. The boost pump&apos;s ventilated design provides the automatic pressure regulation needed to meet the system&apos;s requirements for supporting transient pipeline flow.

Jan 1, 1984

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973

By Tuck M. A

The increasing depth, mechanisation and distance of working areas from surface connections places an ever greater contaminant burden on ventilation airflows. Some British Coal mines are already experiencing significant problems in providing adequate climatic conditions in the working areas and have had to introduce air conditioning. Previous work has shown that in mines of low to moderate virgin strata temperature the application of controlled district recirculation could serve to improve climatic conditions at the working area.

Jan 1, 1988