Search Documents

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By Mark A. Williams

Topography and geology greatly impact the decision of how to plan and operate a surface mine. To extract coal, five primary surface mrning methods are practiced in the United States. These include contour strip. mountamtop removal, area, modified area, and open pit mining methods. The first four approaches are commonly associated with coal mining while open pit techniques, although used in the mining of coal, are more commonly applied to the mining of hard rock, metals, and aggregates. Various sub-routines of the primary surface mining methods are likewrse applied rn the industry.

Jan 1, 1991

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

Possibilities for Flotation Acoustics Monitoring - A Review

Sep 13, 2010

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By Greg S. Williams, Richard W. Givens

This paper examines the effect of prill size consistency, internal panicle density, and oil absorbency on Ammonium Nitrate Fuel Oil (ANFO)-emulsion blends. By analyzing these physical properties of prill and the nature of the blending process, a mathematical model has been developed to theoretically predict blend densities. Calculated densities can now be compared to actual field densities to give an operator a basis for comparing various manufacturers’ emssions and Ammonium Nitrate (AN) during bid solicitation. The lowest priced emulsion and/or AN may not be the most economical, due to the impact of specific physical characteristics. These factors dictate the blending mechanics and resulting density yields for various mixes. The research was driven from observed ‘field’ mixing relationships and data. Ultimately, such a model can be an effective tool in evaluating blends from a cost and performance basis.

Jan 1, 1992

By T Smith, J Hatley

With the increased focus on the need for more uranium mines, this paper presents the design process currently underway for the development of the Millennium deposit in northern Saskatchewan, Canada. This deposit, located 630 - 750 m below surface, will be accessed by two shafts and will be mined by blasthole stoping methods at less than 500 t/d. Mining grade will approximate two per cent U3O8 and mine life is expected to be six to seven years. The project is a joint venture between Cameco, AREVA and JCU. This paper discusses in detail methods used to predict worker radiation exposures, the methods used to monitor the work environment and procedures unique to the uranium industry necessary to minimise worker radiation exposures.

Jan 1, 2008

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By Yoshikazu Hirosaki

How big or small is the Japanese explosive market? Who are the major explosive customers? Is there any big construction project in which a large amount of explosives is expected? What is the future of the explosives industry in Japan? Is it true that there are no ANFO trucks? What is the licensing system for blasters? Is there any education system for blasters?

Jan 1, 2001

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

By L. M. Lowe, D. G. Feasby, J. R. Goode

"Rare earth resources usually contain minor amounts of radioactive elements. The most widely recognised sources of radioactivity are associated with thorium and uranium. However, also present in the resources are isotopes of rare earth elements (REE) that are themselves radioactive, including lanthanum (La-138), lutetium (Lu-176) and samarium (Sm-147). These radioisotopes, as well as remnants of the natural thorium (Th-232) and uranium (U-238, U-235) decay series, can contribute to significant levels of radioactivity in mixed REE concentrates and in separated products. Levels such as these can present challenges for transport, transboundary movement, product storage, workers’ health and safety, as well as waste management issues at the facilities that separate out the individual REE’s. These are discussed in this paper. A particularly challenging radioactive isotope is Ac-227 (a decay product in the U-235 decay series). Actinium behaves chemically similar to lanthanides and hence normally concentrates with REE multi-element composites. Reliable analysis of Ac-227 is not widely available and the methodology required to deal with this challenge is briefly described. A principle reason for minimization of radioactive content throughout REE processing is restrictive specifications by concentrate purchasers in order to reduce waste management challenges. Approaches to the minimization of radioisotope content in REE concentrates and separated products are outlined in this paper."

Jan 1, 2014

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By R. Khanna, M. Dubikova

A variety of carbonaceous reducing materials are being used for the production of ferroalloys. Reductant materials include not just carbons such as coke, coal, char but also bio-carbons in form of charcoal produced from different types of wood. This paper discusses critical properties and reactions of carbonaceous materials and their significance in dictating reductant performance. Main considerations include among others, gasification of reductant, dissolution of carbon into molten metal, and direct reduction of slag by solid carbon. These are discussed in relation to material properties such as structural order, mineral matter content, composition, physical characteristics etc. A brief review of both conventional and novel approaches towards characterisation of carbonaceous materials has been included. Due to complexity and heterogeneity of carbonaceous reducing materials and a wide range of process requirements, the selection of the most appropriate reducing agent will depend on a number of considerations such as the availability of raw material and associated costs, product and process requirements and environmental aspects of waste gas emissions.

Jan 1, 2004

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010