Search Documents

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Gonzalo Chávez

El presente texto describe la lixiviación de oro con tiourea como una alternativa viable para la recuperación de dicho mineral, así como para el medio ambiente. En este sentido, la lixiviación de minerales de oro con solución ácida de tiourea fue evaluada con el uso de carbón activado, re-extracción y electrodeposición, obteniéndose velocidades de reacción y recuperación similares a los obtenidos con cianuro.

Sep 12, 2011

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

One of the most important factors leading to the success of a cement plant is its location. A multicriteria decision-making method is used to rank alternative plant locations. The set of criteria is established and corresponding criteria should be established for each case study, although this multicriteria decision-making approach has broader applicability. In this paper, the analytic hierarchy process (AHP) with 5 criteria is used to develop a location evaluation hierarchy for an alumina?cement plant in East Azerbaijan province of Iran. Five alternatives for the plant location are evaluated. The main criteria are transportation, water supply, power supply, fuel supply and land. Other criteria have the same importance as these five alternatives. The alternatives are ranked by a multicriteria method and the best site is proposed. Keywords: plant location; multicriteria decision-making

Jan 1, 2005

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By Misra V. N

Upgrading of a Koolanooka magnetite iron ore sample provided by Kingstream Steel Ltd was investigated using low intensity magnetic separation (LIMS) and reverse flotation. The ore contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina, with the main minerals in the ore being amphibole (42 per cent), magnetite (39 per cent) and quartz (14 per cent). The concentrate obtained after low intensity magnetic separation contained 66.6 per cent iron and 6.34 per cent silica with an iron recovery of 72 per cent. This concentrate was further treated by reverse flotation to increase the iron content and reduce the silica content to meet the requirements for direct reduction iron (DRI) feed grade.

Jan 1, 1999

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By G. Cockburn

Nkomati Nickel JV exploits the ores of the Uitkomst Complex near Machadodorp in the Waterval Boven district in South Africa?s Mpumalanga Province. Due to factors such as the remote location, stellar growth in production, opencast mining methods, and ore characteristics, a number of innovative processing options were selected. Nkomati has undertaken numerous initiatives over the last few years to improve plant running times, metallurgical performance, and operational profitability. Great emphasis has been placed on effectiveness of management control systems. A number of initiatives such as short interval control and time?in-state metrics have been implemented. A focus on improvement on availability and asset utilization of key items of equipment has been particularly effective. While the ores are remarkably similar to the Merensky and UG2 reefs, the relatively high base metal sulphide content and mineralogical characteristics make metallurgical treatment somewhat different to the ores of the Bushveld Complex. The low head grades and flotation kinetics distinguish Nkomati from other base metal operations. Numerous milling and flotation optimization initiatives have resulted in dramatic improvements in throughput, recoveries, and concentrate grades. This paper discusses the metallurgical, operational, and management challenges and the outcomes obtained.

Jan 1, 2014

By Gualberto Salas Torrelly

El avance tecnológico en los sistemas de iniciación en voladura abarca desde el sistema convencional (Mecha de Seguridad y Fulminantes hasta el sistema de iniciación electrónica, donde a través de un control de vibraciones se controla la energía liberada en un disparo, optimizando la fragmentación y disminuyendo el daño a las paredes del pit. En ese sentido, el sistema de iniciación con detonadores electrónicos, fija con claridad los conceptos de precisión, flexibilidad y seguridad. Por ello, el presente trabajo señala el uso de detonadores electrónicos por la Sociedad Minera Cerro Verde con la finalidad de evaluar sus resultados en seguridad, precisión, fragmentación, vibraciones, y control de daño a las paredes de la mina. Los resultados fueron óptimos -en tanto mejoró la fragmentación, el proceso de carguío y se incrementó el flujo en chancado primario.

Sep 12, 2005

By V. Lakshmanan, Dan Mackie, J. Melnbardis

"Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market, with plans to begin production of a 500 TPD operation in 1984.Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogeneous grinding. In addition to producing marketable coarse graphite by such autogeneous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies. INTROOUCTIONWhen the Black Oonald mine at Calabogie Ontario ceased production in 1954 nearly all North American crystalline flake graphite had to be imported from offshore. Orebodies in the United States were too small or too low in grade to be exploited economically.The Houthillier Township near Mont Laurier in Quebec (Figure 1) was a known graphite-bearing area The Orrwell property in that area was delineated in 1957 Some test work including minor footage of diamond drilling was carried out by Italia Copper and the MHM Syndicate prior to 1981 when Orrwell acquired the property"

Jan 1, 1984

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982