Search Documents

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

Introduction MINING IS THE BRANCH OF INDUSTRY involving the exploration and removal of minerals from the earth (figure 1). Mining is one of the oldest and most important endeavors of humankind, because it provides the raw ingredients for most of the material world around us and, like agriculture, is the lifeblood of civilization. The main objective of any type of mining is to remove the valuable material economically and safely with minimum damage to the surrounding environment. The Earth has many natural resources on which we depend that must be mined. Coal, oil, gas, and other mineral fuels are used for heating electricity, and numerous industrial processes. Nonfuel minerals such as iron ore, precious metals, and industrial metals, and nonmetallic materials like sodium and potassium are used in chemical and agricultural applications. Even crushed stone used in road building and other construction projects must be mined. Mining affects our standard of living and impacts almost everything we do. A myriad of items that we use in our homes and offices and for transportation, communications, and national defense all require minerals (figure 2). For example, more than 30 different minerals are needed to make a television or telephone! Table 1 lists several commonly mined materials and some of the end uses in our daily lives.

Jan 1, 1995

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation. In order to insure accurate data, tight field controls were adhered to during the drilling and blasting process as they related to blast design, bench preparation, pattern layout, drilling and blasthole loading. Following the blast the excavation and crushing procedures were studied to quantify any down stream advantages due to improvements in fragmentation. This study will help provide the industry with information as to the advantages of high accuracy electronic blasting systems over conventional pyrotechnic systems and show the results of an operation utilizing electronic detonator technology through their production season.

Jan 1, 2000

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

By D N. Castendyk, J L. Mauk

The world-class Waihi (>6.6 Moz Au, >41.8 Moz Ag) and adjacent Favona (>0.5 Moz Au) deposits are within a single volcanic-hosted epithermal Au-Ag district located in the southern Coromandel Peninsula, New Zealand. Gold and silver mineralised quartz veins at both deposits are hosted in porphyritic andesite flows of the Waipupu Formation. Both deposits have veins surrounded by intense widespread hydrothermal alteration that is characterised by the assemblage of quartz, pyrite, adularia, illite or interstratified illite-smectite, plus less common chlorite and albite, which is locally overprinted by minor calcite or rare kaolinite. Quantitative mass transfer calculations using Gresen's general metasomatic equation indicate that hydrothermally altered andesite at both deposits is enriched in silicon, potassium, rubidium, barium, sulphur, gold, arsenic and antimony, whereas sodium, strontium and calcium are mostly lost. Iron and magnesium show mixed gain and loss. Element gain or loss can be directly related to the prevailing alteration mineralogy. Addition of potassium, rubidium and barium coupled with the concomitant loss of sodium, strontium and calcium in intensely altered wall rocks corresponds to the replacement of plagioclase by adularia or illite. Partial retention of sodium and calcium reflects the presence of hydrothermal albite and calcite, respectively. Mass balance calculations show distinct element gain and loss that can be related to the intensity and type of alteration mineralogy. However, because most rocks are intensely altered and the progression into less altered peripheral rocks is not observed in this study, the lateral extent of elements gain or loss is unconstrained with anomalies extending at least 200 to 300 m away from major veins.

Jan 1, 2003

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

By A. Adu-Acheampong

Stope instability at Ashanti Goldfields Company Ltd. (AGC) is a major concern. Using information from field mapping, major discontinuity sets were defined, Rock Quality Designation (RQD) was determined. The stability of wedges in the stope walls was assessed using the commercially available computer program UNWEDGE(Rock Science, 1992). Analytical results indicate that the presence of graphite infilling in joints contributes to instability, while steeply dipping joints control wedge slabbing and wedge toppling in the hanging wall. Stable stope widths and dimensions were determined to range from8.1 to 30 meters (m).

Jan 1, 2003

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007