Search Documents

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By C. Birch

"A mineral resource royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In South Africa, this payment is made to the State as holder of the mineral rights (The Mineral and Petroleum Resources Royalty Act of 2008). The principle purpose of this research paper is to identify if the State is benefitting from the mineral resource royalty by considering its impact on seven individual Witwatersrand gold mines.For this study, a simple financial optimiser model was created in Microsoft Excel that links the ore flow, block listing and the cash flow (excluding or including the cost of the mineral resource royalty). Mixed integer linear programing (the Excel Solver function) is utilised to optimise either profit or NPV (at 9% and 12%) by adjusting the cut-off grade.The impact on each of the seven mines mine was different but overall R7.9 billion is estimated to be paid in mineral resource royalty over their expected remaining lives. Due to the cost of the mineral resource royalty and increasing the cut-off grades, the total revenue decreases by R10 billion. A significant portion of this lost revenue would have been paid to the State in the forms of other taxation including company income tax which decreases by R2.8 billion. It is recommended that an industry wide investigation be conducted to determine if the resource royalty is adding to the State’s revenue, or destroying value including premature job losses. IntroductionTaxation of mining companies has become a very topical subject in the context of the postapartheid South African economy. There have been increasing calls for equitable re-distribution of mineral asset wealth for the benefit of all South African citizens and not just to an elite few. As part of the Mineral and Petroleum Resources Development Act (MRDPA) of 2002, the Mineral and Petroleum Resources Royalty Act of 2008 was introduced and came into effect in 2010 (South African Revenue Services, 2008). A mineral royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In the case where the holder of the mineral right is the State, then this payment is made to the State (Cawood, 1999). Studies on the potential impact of the mineral resource royalty on the minerals industry have been conducted during the formulation of the Act and subesquently. These include Cawood and Macfarlane (2003), who suggested a cap of no more than 3% (Cawood and Macfarlane, 2003), as well as Cawood (2011), who predicted rising cut-off grades and thus reducing mineral reserves. In 2013, Grobler completed a Masters in the Faculty of Economic and Management Sciences at the University of Pretoria and concluded that the impact of the mineral resource royalty on the economy is positive. She stated that the royalty has caused operating expenses to increase, but this does not appear to be significant. Furthermore, she stated that the royalty has not affected the way the mining industry operates (Grobler, 2014)."

Jan 1, 2016

By John S. Pack

The last 25 years have seen rapid expansion in the use of helical screw pile foundations and tiebacks for new and retrofit construction of buildings and earth retention structures. An estimated $100 million was spent in 2002 on helical foundations and tiebacks in the United States alone. While design information is available in the literature, information regarding quality control, inspection and performance monitoring is lacking. Recognition of at least one manufacturer's helical foundation material by the Uniform Building Code, Standard Building Code, and BOCA (all three codes now combined into the ICC International Building Code) has given added urgency to the dissemination of reliable and practical quality control, inspection and performance monitoring procedures. This paper describes a set of such procedures that have been followed for 17 years by engineers experienced in the industry who have directly installed or been involved in the installation of over 140,000 helical foundations and tiebacks in divers soil conditions for various types of structures, including earth retention structures. Topics covered include design responsibility, building code listings and requirements, manufacturer ISO certification, manufacturing process, material and installation specifications, installation contractor certification, field placement, installation procedures, field inspection, building code inspection and performance monitoring. The paper concludes with a step by step example of practical quality control, inspection and performance monitoring procedures on a typical helical foundation project.

Jan 1, 2003

By N. Shariatmadari

Two dry docks are currently under construction on the northern banks of the Persian Gulf by Iran Shipyard and Offshore Industries Co. (ISOICO). The construction of these dry docks forms a huge civil offshore project. The foundation system include more than 6500 large diameter (40-48 inch) spiral pipe piles with embedded depth varying from 18 to 25 meters. Extensive geotechnical subsurface investigations were carried out in the project site in order to provide enough information and proper perspective on the underlying soil layers. The results of geotechnical investigation indicated that a 20 m thick dense silty sand layer exist which can be considered as the main bearing stratum. Due to short clear distance between the piles (less than 3 m) refusal occurred for some piles, accordingly led to actual length less than their design length. To verify and in-situ evaluation of piles capacity, static and dynamic full scale loading tests programme were performed. The data from 40 static compression and tension and also 50 dynamic tests with PDA were interpreted and analyzed by current approaches and CAPWAP software. The results of analysis demonstrated that the safety factor of bearing capacity of piles must be increased to reach a safety factor of about 1.8. To achieve this purpose the interaction of combined piled-raft system has been realized.

Jan 1, 2007

By D R. Carr

The installation of the Flotation Capacity Project flow sheet in the copper concentrator at Mount Isa Mines Limited has recently been completed. The project involved increasing the flotation capacity with Wemco tank cells and Jameson cells as well as changing the copper cleaner circuit layout. The engineering design and construction for the brownfield expansion had significant involvement from operational, maintenance and technical personnel adopting the same approach as the highly successful George Fisher project in the Lead/Zinc Concentrator at MIM. The involvement of people familiar with the concentrator allowed for smooth integration of the changes into an operating concentrator with minimal downtime. Detailed circuit analysis over many years identified opportunities for improvements in the flotation circuit for both grade and recovery. This paper describes the program of work that led to the Copper Concentrator Flotation Capacity Project, and the implementation of the circuit expansion and flow sheet changes that resulted in an overall improvement in the circuit recovery.

Jan 1, 2003

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

The tenth annual Mine Resale Evaluation was held in conjunction with the RMCMI 2001 convention at the Steamboat Springs Sheraton Resort, Steamboat Springs, Colorado June 23 through 26. The purpose of the mine rescue evaluation program is to provide an opportunity for mine rescue teams to learn new skills and improve their existing ones in a non-competitive environment. Several staged ?disaster? scenarios were held where the teams are called upon to exhibit their life saving abilities. The evaluators meanwhile are offering suggestions, both verbal and written, to help the teams better understand the situations presented them. This non-competitive environment allows the teams to work together and share their knowledge with fellow mine rescue teams providing everyone with a positive learning experience. Mine Rescue Chairman Bill Balaz, Balaz & Associates, was in charge of coordinating the events. Six teams consisting of seven to twelve members each (totaling 60 members) participated in the three-day event. Each ream was required to respond to direr different real-life scenarios plus a written general knowledge test daily. Cindy Burnham has assisted Bali, for a few years. Her responsibilities include grading all of the written tests. This year&apos;s tour professional evaluators included Art Seanz (Hazardous Ma¬terials) of Western Environmental Associates ; Guy Norton (Ropes), Guy Horton Rope Rescue; Mary Bailey (Medical), MBA Training and Morley Hense (Confined Space). Carolyn Durga, BHP Coal, also assisted in hazardous materials and medical scenarios. They each provided three different challenging mock situations per day per team. The teams had no prior knowledge of what the scenarios would be as details were provided only as they arrived. Ten volunteer victims added much drama and excitement to the event. Their realistic enactment, complete with false blood makeup and severed limbs, made for some very tense scenarios. The Mine Rescue Teams participating this year were BHP LaPlata, BHP Navjo, BHP San Juan, all from Farmington, New Mexico; Bridger Coal Co., Rock Springs, Wyoming; Sabine Mining, Longview, Texas; Solway Minerals, Green River, Wyoming and Western Energy Co., Colstrip, Montana. Many new friendships were made and much knowledge shared. A swap meet was held Saturday afternoon for the teams to exchange miscellaneous equipment, hats, shirts, etc. The trams were asked to evaluate the program and the evaluators. They responded with many positive suggestions that will help improve the upcoming events in the years to come. Culmination of the Mine Rescue program was a Tuesday morning awards breakfast where the teams were presented with trophies. Each member was also given a gold pin with the words Continuing Challenge - Ropes.&apos; The pin was the first in a series that will be given over the next few years. The participating victims and evaluators were also commended for their outstanding efforts. Special signed "Victim" shirts were given to select volunteers. Sponsors for the Mine Rescue program were Flanders Electric Motors, Magnum Metals, Rocky Mountain Electric Motors, Sedona Consulting and Balaz & Associates. Many hours of volunteer tine and effort from various family members of participants helped make the 2001 event a huge success.

Jan 1, 2001

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper.

Jan 1, 2014

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

Upgrading of Superfine Low-Grade Haematite Ores by Reverse Floatation Direct Reduction Low Intensity Magnetic Separation Process

Sep 13, 2010

Interest in industrial minerals in recent years has increased to such an extent that it has taken them into the mainstream of the Australian mineral industry. Notwithstanding that time series data on the values of production, exports, and imports show that industrial minerals are overshadowed by metals and energy minerals, their contribution to the national economy is important and more significant than would seem to be indicated by the statistics. Whereas the ex mine value of metals generally includes some processing (at least to a concentrate stage), most industrial minerals are valued at little more than their extraction cost, in addition to which such costs are generally low because most industrial minerals are exploited in low-cost surface operations. Consequently, values of mine production of metals and industrial minerals are not strictly comparable in that values of mine production of metals tend to be overstated Short term growth of the industrial minerals sector is assured because of several new projects already commissioned but not yet reflected in the statistics. Longer term growth is also assured, based on various other major projects that are likely to come on stream in the early to mid 1990s.

Jan 1, 1989

By A. D. Thomas, V. N. Rampton, S. Paradis, C. F. Gleeson

"A shallow till sampling program was completed on a 1 km grid over the St . George Batholith in southern New Brunswick. The ""B"" soil horizon was analyzed for Cu, Pb, Zn, Ag, Co, Mo, U and Sb and the heavy minerals from the ""C"" soil horizon were analyzed for W, Sn and A u. The results delineated four of five recorded W occurrences, three of four recorded Mo occurrences, all recorded Cu occurrences and one recorded Au occurrence. The results indicate that shallow till sampling in conjunction with bedrock and Quaternary mapping can inexpensively define exploration targets in terrain similar to that underlain by the St. George Batholith.A similar program was carried out in eastern Ontario involving the analysis of four separates from the till, the ""8"" soil horizon, the -50 mesh fraction, the -250 mesh and the heavy mineral fraction of the ""C"" soil horizon and humus. Also sampling was carried out near known gold occurrences at closer spacings. Regionally, anomalous results from all sample media clearly defined a large auriferous shear zone and associated splays. Over one known showing all media clearly defined the showing and a secondary zone. On the regional scale the heavy mineral fraction gave the best anomaly definition and contrast, but the -250 mesh fraction was found to be the most cost effective for defining exploration targets. For detailed surveys, humus was found to be cost-effective."

Jan 1, 1986