Search Documents

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By Qing Wang

In this method the state of an open-pit mine is represented by the number of benches that are mined in each predesigned mining phase (or pushback). Consequently, a specific mining schedule can be represented by a sequence of states which starts with the topography of the mine site and ends with the ultimate pit. For a given set of mining phases all feasible states are first generated and sequences of states are then evaluated for technical and economical feasibility. The best sequence, which gives the maximum net present value (NPV), is found by applying a dynamic programming optimisation algorithm. The algorithm also optimises the cut-off grade which satisfies the mill feed requirement for each planning period. It was found that the algorithm can be used not only for scheduling but also as an effective tool for analysing the effects of mining and milling capacities and cut-off constraints on the mining schedule and the total NPV. The algorithm, which was programmed in C, was successfully applied to a large Au-Cu deposit

Jul 1, 1996

The mineralisation consists principally of layered pyrite, phalerite and galena, situated conformably within a sequence of tuffaceous, bituminous shales and dolomitic sediments that include slump breccias. The sediments show little evidence of post sedimentary reconstitution. A volcanic-exhalative-sedimentary origin is postulated for the mineralisation. Attention is drawn to the similarity between the McArthur deposit and the lead-zinc-silver orebodies at Mount Isa. The primitive nature of the sulphides is reflected by their adverse metallurgical behaviour, and it seems that the best prospect for milling and flotation benefication may lie in the production of separate zinc and bulk concentrates

Jan 1, 1968

By A B. Christie

Space-based synthetic aperture radar (SAR) data is becoming available over much of the world, includingNew Zealand. Radar imagery has a number of very advantageous features, including all-weather capability; it also has artifacts, such as layover, which require processing before these data may be used to best effect.   This paper gives an outline of SAR, details the image processing required, and discusses the use of the first New Zealand Japan Earth Resources-1 SAR data to aid geological mapping on the Coromandel Peninsula.

Jan 1, 1994

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004

By F. Maciosek, D. Denton, J. Johnson

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and personnel from Coeur Silver Valley, Wallace, ID, conducted tests using rock strain strips and Split-Set rock bolts instrumented with strain gauges to monitor wall rock strain at the Galena Mine, Osburn, ID. The objective of the test was to identify whether strain on the rock bolts increased prior to a rock burst. Although results were inconclusive, researchers learned that the Split-Set rock bolts yielded in stick-slip fashion in the highly jointed walls of the stope. The bolts were also bent as stress was redistributed following blasting and subsequent movement along joints in the wall rocks.

Jan 1, 2004

By William R. Yernberg

The 2003 Rapid Excavation and Tunneling Conference (RETC) was held at the New Orleans Marriott, New Orleans, LA, June 15-18. The New Orleans conference was the 16th since the RETC was formed in 1971. This year’s conference was sponsored by the Society for Mining, Metallurgy, and Exploration, Inc.(SME), with co-sponsorship of the Construction Institute of ASCE. Attendance at the meeting was 1,178, a conference record. This was up significantly from the771 attendees at the 2001 meeting in San Diego, CA. The RETC was formed to “advance the engineering and scientific knowledge of rapid underground excavation and tunneling through interdisciplinary meetings, publications, technical-educational exhibitions and encouragement of research.” The RETC conferences are now held every other year. They provide an opportunity for individuals to meet with designers, contractors and manufacturers associated with the tunneling industry to share experiences in all phases of tunnel design and construction.

Jan 1, 2003

By Hugh Douglas

In the past two years recent increases in silver prices over levels that prevailed for many years have changed supply/demand patterns. On the supply side, a silver mining boom is in progress in the United States and elsewhere. On the demand side, traditional uses of silver by individuals are dropping while industry is conserving. These changes will alter the supply/demand balance and bring about more moderate rises in silver prices, which in turn will impact the mining industry.

Jan 1, 1981

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene.   Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

By Peter Makuvise, Alain M. Bantshi

"The Mazowe Gold Mine is managed by Metallon Gold (Zimbabwe) and is situated in the west-central part of the Harare greenstone belt. Orebodies here generally comprise shear zones which are in-filled with gold-bearing sulphides and quartz. The mineralised zones are up to 1 m in width, have average grades of 4 to 5 g/t, and mostly dip between 10º and 60º to the north.Mazowe Mine is one of the oldest mines in Zimbabwe, and exploration and development in this region dates back to 1890, with over 1.4 million ounces of gold produced to date. Mazowe mine comprises two underground operations, Mazowe and the BSV sections. Ore is processed in a single plant which consists of conventional crushing and milling and carbon-in-leach facility.Baldmin Projects was awarded the contract for the design, construction and commissioning of the 60,000 tonnes per month plant at Mazowe mine in 2014 for the processing of sand and slimes tailings from previous operations at Mazowe mine. The average grade of the tailings is 1.1 g/t. The plant consists of feed preparation, grinding, flotation, thickening of flotation concentrate, and carbon in leach (CIL). A pump station for hydraulic mining of the slimes tailings dam also part of the plant.Key features of the Mazowe sands Plant are described and include:• Hydraulic mining of gold tailings dump.• Feed preparation section that includes a (W x L) 2.4 m wide x 4.8 m trash screen, 250 m3 surge tank, a cluster cyclones with 2 x 500 mm diam. Cyclone.• Comminution circuit designed for a bond work index range of 10-12 kwh/tonne. comminution circuit is constituted with 3 ball mills, 1.83 m diam. X 6.71 m Long, 280 kW.• Flotation circuit comprising rougher bank, scavenger bank and cleaner bank. Rougher Scavenger bank is constituted of 6 x 6m3 flotation cells and 3 x 30 m3 flotation cells and the cleaner is constituted of 3 x 6 m3 flotation cells.• Concentrate Thickening with 6 m diam. Thickener.• Concentrate CIL (carbon in leaching): CIL circuit is comprised of 7 tanks with 2 leach tanks and 5 Carbon in leach."

Jan 1, 2017

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By L. J. Prosser, Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.