Search Documents

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By A. George Stern

The literature dealing with the drilling of oil wells has become extensive during the last few years, and oil men can find much information relating to drilling muds in the technical literature of the petroleum industry. Although large tonnages of clay are used in preparing drilling mud (also known as drilling fluid), almost no information has been published to apprise the clay industry of the types of minerals used, with their requirements and limitations. It is from this point of view that the present report has been prepared.

Jan 1, 1941

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

By Keith L. Harris

The economy continued to expand during the second quarter, but at a much slower pace than expected. According to latest estimates released by the Department of Commerce, the real gross national product (GNP) grew at a seasonally adjusted annual rate of 0.6% compared with a revised growth rate of 3.8%2 for the first quarter of 1986 and 2.3% for the second quarter of 1985 (table 1). The strong growth of personal consumption expenditures, Government purchases of goods and services, and residential investment was moderated by the growing trade deficit, declining investment in business inventories, and the continuing lag in nonresidential investment. Much of the decreased capital spending for the nonresidential sector for the first and second quarters resulted from reduced petroleum exploration and drilling in response to low petroleum prices. Capital spending and trade continue to be areas of weakness for the economy. Real new plant and equipment expenditures for 1986 are estimated to be 1.3% below those of 1985 (table 2). Real net exports of goods and services decreased $24.6 billion, as exports declined 5.6% and imports grew 16.5%. About two-thirds of the $19.3 billion increase in imports was in petroleum and petroleum products, which, because of their lower prices, should help the economy in the future. In response to the sluggishness of the economy, the Federal Reserve System reduced its discount rate from 6.5% to 6% in early July. Inflation, as measured by the fixed-weighted GNP price index, declined from a revised 2.5% in the first quarter to 1.9% in the second quarter because of significantly lower energy prices.

Jan 1, 1986

By P. M. Robinson, M. B. Bever

The heats oj formation at 273°K of the compounds CdTe, I)z2Te, InTe, In2Te3. In2Te5, SrzTe, and PbTe have been rleasrred in a liquid metal solutiotz caloritrete? 1.t1itlz bismuth as solvent. The?, are iterpretecl in yelation to tlze stability and bonding of the cott/pozltzds. Tile heats of fusion atzd the melting- points of tlze cotlzpounds InTe and Itzz,Te3 1lcti.e been measured in a cotrslant-temperature gradient calorimeter. The entropies of fusion are disc,ztssecl in YIIIS 01. the degree of order in the solid at the melting point. THE heats of formation of the tellurides of cadmium, indium, tin, and lead have been measured as a continuation of research on the thermodynamic properties of compounds of tellurim.' The tellurides of these metals were selected with a view to examining the relation between the heat of formation and the position of the metal in the periodic system. The elements cadmium, indium, and tin are in the same period and tin and lead are in the same group of the periodic system. The tellurides of indium are of special interest because four compounds, In2Te, InTe, In2Te3, and InzTe5, occur in this system. The available information on the heats of formation of the compounds investigated consists of values for CdTe, SnTe, and PbTe derived from electromotive-force measurements,J a value for CdTe obtained by tin solution alorimetr, and values for InTe and In2Te3 determined by combustion calorimetry.5 These values, however, refer to various temperatures ranging from 273' to 673°K and some of the reported error limits are large. Liquid metal solution calorime-try may be expected to yield more accurate values for the heats of formation than electromotive-force measurements or combustion calorimetry. The heats of fusion and the melting points of the compounds InTe and In,Te3 were determined in a constant-temperature gradient calorimeter. No published information appears to be available on the heat of fusion of these compounds. The results reported here give an indication of the degree of order in the solid compounds at the melting point. 1) MATERIALS AND EXPERIMENTAL PROCEDURE Materials. Samples of the compounds SnTe and PbTe were obtained from the Westinghouse Research Laboratories and samples of the compound InTe from Lincoln Laboratory, Massachusetts Institute of Tech- nology. Additional samples of the compounds InTe, SnTe, and PbTe and samples of CdTe, In2Te, In2Te3, and In,Tes were prepared from 99.995 pct Cd (Baker Chemical CO.), 99.999+ pct In (American Smelting and Refining Co.), 99.99 pct Sn (Baker Chemical Co.), 99.999+ pct Pb (Fisher Scientific Co.), and 99.999+ pct Te (American Smelting and Refining Co.). Stoichiometric amounts of the component elements were melted in sealed, evacuated Vycor tubes. The melts were held at approximately 100°C above the liquidus for about 16 hr and shaken repeatedly. The melts of the compounds In2Te and InzTe5, which form by peritectic reactions, were quenched into iced water. The melts of the other compounds, which have congruent melting points, were slowly cooled to room temperature. The samples were then annealed for 5 days at approximately 50°C below their respective solidus temperatures. Metallographic examination did not reveal any evidence of second phases or segregation. At least two batches of each compound were prepared. Samples from each batch were used in determining the heats of formation and, in the cases of InTe and In,Te3, the heats of fusion. The Heats of Formation. The heats of formation at 273°K of the compounds were measured by metal solution calorimetry with liquid bismuth at 623" as solvent. In this technique, the heat of formation is determined from the measured heat effects on dissolution of the compound and of a mechanical mixture of the component elements. The difference between these heat effects adjusted for changes in the composition of the bath gives the heat of formation at the temperature from which the samples are added to the bath (273°K). The experimental technique and method of calculation have been described in detail elsewhere.= It should be emphasized that the reported heats of formation depend on the thermodynamic data used in calculating the heat effects for the calibration additions. In the present investigation, the calorimeter was calibrated by adding pure bismuth at 273°K to the bismuth bath at 623°K. The reported heats of formation are based on a value of 4.96 kcal per g-atom for the difference in the heat contents of bismuth at 623" and 273". If a new value for this quantity becomes available, the reported results may be adjusted in direct proportion. The concentration of solute in the bath at the end of a calorimetric run did not exceed 1.7 at. pct and was usually less. In this range, the heat effect on dissolution of the solute was a linear function of the concentration of solute. In determining the heats of formation of the compounds in the system In-Te, a few runs were carried out in which two neighboring compounds such as InTe and In,Te3 and the corresponding mechanical mixtures of the components were added to the calorimeter. The

Jan 1, 1967

By Charles White Merrill

Money is one of the most .pervasive elements in human life. The compensation for a workman's daily efforts is expressed as a wage and is measured in money. What an individual may consume depends largely on his income which also is expressed in terms of money. If he would start an enterprise its size would be determined in large part by the amount of money available for capitalization and its success would be measured in net income expressed in money. In short, the most widely used common denominator for comparing merchandise, real property, jobs, enterprises, gross national product, or personal success is money. Despite this use of money by almost everyone past infancy to express his appraisal of the in- numerable values he sees around himself, the complexity of the device called money makes its nature and workings a mystery to most users. Some of the difficulty in understanding money results from the fact that it has three distinct but interrelated functions: (1) a medium of exchange, (2) a unit of account, and (3) a store of value. In many statements about money the discussion moves from one function of money to another without the speaker or the listener recognizing the changes. For example, the housewife says "We took the money we had saved up to make the down payment and after twelve monthly payments the television will be ours." When this housewife spoke of "saving up the down payment" she referred to money in its function as a store of value; when she spoke of "the down payment" she was using money as a medium of exchange; and when she referred to the "monthly payments" she spoke of money as a unit of account. Another cause of confusion in understanding money is its paradoxical nature in that it represents both the power to produce and the power to consume. For example, when the rich uncle dies one nephew may regard his inheritance as an opportunity to buy a farm and leave the ranks of the wage earners to become an independent producer, whereas the other nephew may regard his portion as the means of living in complete leisure as a pure consumer.

Jan 1, 1959

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By Sutham Niyomwas

Synthesis of alumina-mullite-silicon carbide composite (Al2O3-Al6Si2O13-SiCw) was obtained in situ by carbothermal reduction of a mixture of kaolin and two different silica sources. The carbothermal reduction was carried out in a horizontal tube furnace under flow of argon gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of alumina, mullite and silicon carbide in the form of whiskers. The effects of adding two different silica sources of rice husk ash and silica powder to the mixture of kaolin and activated carbon were investigated. XRD and SEM analyses indicate complete reaction of precursors to yield Al2O3- Al6Si2O13-SiC as product powders, with the SiC having whisker morphology.

Jan 1, 2006

By W. W. Adams

Increased employment and a lower accident-frequency rate were the outstanding features of the metal- and nonmetal-mining4 industries of the United States in 1939 compared with 1933, according to reports furnished by individual mining companies to the Bureau of Vines, United States Department of the Interior. Except for 1937, the reports for 1939 showed gains both in number of employees and number of mar -hours worked over all years since 1929. The accident-frequency rate per million man-hours of exposure to mining hazards was lower than in any year since 1925. Reports for 1939 revealed a total of 111,909 men employed in and about mines, an increase of inure than 8 percent over 1931 The total volume of labor performed at all mires was slightly more than 299 million plan-hours, an increase of mare than 10 percent over 1938. As these gains suggest, the average employee had a longer period of work in 1939, the increase amounting to r workdays per employee.

Jan 1, 1941

By C. W. Owings, J. J. Forbes

"Although coal-mine explosions rank third among causes of underground fatalities, they receive more wide-spread attention than any other accidents in mines because frequently many persons lose their lives in a single disaster. Each bituminous coal-mine explosion endangers the lives of approximately 100 persons--the average number employed underground in a commercial mine. A critical analysis of coal-mine explosions in a restricted district gives a cross-section of relative existing explosion hazards, of common causes of ignitions of gas and dust, and of effective prevention measures. The Safety Division of the United States Bureau of Mines is collecting data on coal-mine explosions in the various States, and this circular is one of a series analyzing the causes and recommending methods for thy prevention of similar occurrences,The data on this circular are based on records of the United States Bureau of Mines and the West Virginia Department of Mines. Unfortunately practically all of the early records were destroyed by fire in the State House at Charleston, W. Va.; the remaining records were made available to the authors by N. P. Rhinehart, chief of the Department of Mines, and his cooperation is gratefully acknowledged.The earliest available reference to coal in West Virginia is that made by John Peter Lally who in 1742 found ""a great plenty of coals"" near a river later called Coal River. In 1809, Nicholas Roosevelt found coal along the Ohio River and used it on the New Orleans, said to have been the first steamboat west of the Allegheny Mountains. In 1810, Conrad Cotts opened a mine near Wheeling and sold coal for domestic purpose in 1812, a mine was opened on the Ohio River opposite Mason City and produced 1,200 bushels of coal that year. In 1840 the total West Virginia coal production was 298,691 tons; in 1863, the production had increased to 444,468 tons, and in 1883, to 2,335,833 tons. During this period apparently most of the coal was extracted from coal outcropping on the hillsides; little danger of gas ignition existed at that time, but explosions from blown-out shots occurred frequently. On February 22, 1383 the West Virginia legislature enacted legislation providing for a mine inspector to inspect the mines of that State, to prevent mine accidents, and to insure properly ventilated mines.In a special report to the Governor on December 31, 1884 the Inspector of Mines reported:We have 5 shafts, in 4 of which there is more or less gas; and in 1 of our drift mines there was an explosion on the 27th day of March 1880, whereby 2 men were killed and a boy badly burned.Table 1 lists 287 explosions in West Virginia coal mines. Several early explosions were listed in the annual reports of the West Virginia Department of Mines as ""blown-out shots"" or ""powder explosions"". The injuries usually were described; explosives accidents have been eliminated from these and other available data, and only those in which dust or gas were involved have been included in this paper as explosions."

Sep 1, 1934

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By R Tweedie

'The politics of mining in New Zealand' is a topic I chose myself because of its importance in the future of the New Zealand mining industry. There are many people in the industry who are cynical about politics, cynical about politicians and definitely cynical and often critical of political decisions. In fact, many industry people say they don't want to get involved in politics, they just want to get on with the business of exploration or mining. The point of my address is that politics is important and the industry cannot afford not to participate in the political process.

Jan 1, 1991

By Charles W. Merrill

AN ADEQUATE, dependable, and continuing supply of raw materials is indispensable to tile the United States and its industries in meeting the needs of an expanding Population, a rising standard of living, and the national security. The primary responsibility for appraising the status of the country's mineral supply and for making appropriate recommendations within the executive branch and to the Congress has been pinned in the U.S. Department of the Interior. In fulfilling its role of governmental responsibility for raw-material supplies and their efficient utilization, the Bureau of Mines has analyzed the factors in current and future mineral supplies and demands and has developed 87 statements for specific commodities that assess the national position and problems for these metals, minerals, and mineral fuels. These statements, which constitute the chapters of this volume, are based on lire assumption that nearly till production and consumption of materials in the United States are to be by private individuals and organizations, in accordance with the Nation's devotion to a private-enterprise economy.

Jan 1, 1960

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company's Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

The contribution of minerals to the growth and development of the United States is best demonstrated by the uses which have evolved during the past two centures. During pre-Revolutionary days the colonies were essentially agricultural in character, producing cotton, tobacco, rice, indigo, grains and flour, fish, livestock, dairy products, and timber. Shipbuilding was the major manufacturing industry. In 1763, the total value of exports for Virginia, Maryland, New York, Pennsylvania, and Massachusetts was £2,722,000, of which £55,000, or 2 percent, was for "copper ore, and iron in pigs" (3)1 and £49,000 was for 21,000 barrels or hogsheads of "pot-ash." The value of 75 ships built for sale in 1763 by the colonies was £61,500.

Jan 1, 1976

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015