Search Documents

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By Terry R. Guilinger

A minitest of the new potassium chloride-potassium carbonate two-stage in situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing carion-exchange reactions. The test a1 so indicates permeability anisotropy and the existence of disturbed flow fields. The research was partially funded by the U.S. Bureau of Mines.

Jan 1, 1984

By George M. Fowler, F. E. Gregory, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By William M. Agar, F. E. Gregory, Joseph P. Lyden, George M. Fowler

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By F. E. Gregory, George M. Fowler, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By Cyril Jones

13.9-1. Introduction. Any mining venture or project is undertaken with a view of gaining some benefits, which, with the modern limited corporation, means earning a return to the stockholders for the use of their funds. Thus, any manager, when confronted by an opportunity of expending funds, must realize that the funds should generate a satisfactory return. The problem then becomes one of how the manager should best expend, if he should expend, funds for opportunities that become available to him. In the evaluation of a mineral property, or of a project within an operating mineral property, there must be cognizance of the fact that the final return is dependent on many factors that are not present in other industries. The primary factor in mining operations is the orebody, which has a diminishing life. This diminishing life gives the decision maker a range of choices; for by expending more capital for a larger plant, he can work the deposit out in a shorter period (16). This may, in fact, maximize the return on the investment. Alternatively, he may wish to maximize the total profits, a course which usually requires a lower capital investment and allows a longer working life for the deposit before final depletion. Other factors that have great importance in the evaluation of mining projects are the taxation treatment of mining profits from the viewpoint of depletion, depreciation, and investment credit. Investment opportunities involve expending funds at the present time in return for future benefits. These future benefits have a degree of risk in that the annual amounts of benefits and their duration cannot be fore- cast accurately. The treatment of risk in economic analysis involves the quantification of the degree of variability of the expected future benefits and also of the initial capital expenditure. This treatment in mineral exploration may be extended to cover the initial search for an orebody

Jan 1, 1968

By H. R. Hanley, C. Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial developmerit in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained . British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1944

By Frank J. Wiebelt, Spangler Ricker

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on.the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these toles, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Leonard Obert, Wilbur Duvall

"INTRODUCTION 'The investigation reported herein is part of a comprehensive research program being conducted by the Metal Mining Research Section, Mining Division, Bureau of Mines, on pressure problems in underground mines. This program was initiated in 1937 and for the first 3 years was concerned primarily with measurement of the pressure on mine pillars and supports and their strength. 4/ 5/ During this period, investigations were conducted in both the laboratory and the field in the comparatively shallow load and zinc mines of Missouri and Oklahoma. As a result a seismic method of determining the pressure on mine pillars was developed.Before this research program was initiated, Chas. F. Jackson, chief of the Mining Division, suggested that rock under pressure might give rise to noises inaudible to the unaided ear - that is, subaudible noises. As a result of this suggestion, listening tests were made concurrently with the routine pressure measurements to see if any rock noises were present; with one exception, it was found there were no rock noises in any of these shallow mines. At the same time, pressure measurements disclosed that, with one exception, pillars were not under pressure amounting to more than 10 percent of the crushing strength of the rock. The one exception was a pillar in the Big John mine of the Eagle Picher Mining & Smelting Co. in the Tri-State district, which showed some physical evidence of failure, such as small cracks and spalling; it was reported that the pillar had been heard to crack or snap at intervals. Listening tests in this pillar disclosed that subaudible noises of comparatively small intensity were present and occurred at 1- to 2-minute intervals, on the average. Unfortunately, owing to the shortness of this pillar it was impossible to make any pressure measurements."

Jul 1, 1942

By A. B. Cummins

THE past year has been of unusual interest for industrial minerals. It is increasingly evident that requirements for these raw materials move with general economic trends. Thus, with a peak year in the construction, chemical and petroleum industries, the nonmetallic mineral industries have been brought into the complex maze of an economy in which military spending is in the billions and in which the national income and wholesale commodity prices reached new levels. Many industrial minerals are of first rank essentiality in the defense effort and its supporting industries, and since some of these are of limited supply and others dependent on imports, the problems of procurement, distribution and conservation of available supplies make a complicated pattern. Despite some drawbacks and weak spots, the industrial mineral industries have, in general, met the national situation with great credit and many new production records have been set. The general accomplishment in 1951 should be one of satisfaction with confidence for the future. Difficulties, unsolved problems and uncertainties should not obscure the general trend which many consider optimistic. Prices in the main have been upward, in line with the inflation spiral, but nonmetallics appear with some exceptions to be behind the general increases. Labor difficulties have not been serious throughout the year. Retarding influences in expansions and planning have been the uncertainty of the Korean and international situations and a lack of confidence by many in the government economic program and its ultimate impact on the economic structure. It must also be kept in mind that stockpiling, unless all-out war develops, reaches a level and then ceases to be a major sustaining factor in the mineral markets. In accordance with the Defense Production Act of 1950 various control agencies have been set up to establish the desired rate of stockpile acquisitions. The objectives are subject to change depending on availabilities and needs-military, industrial, and civilian. In some minerals there has been disagreement on actual stockpile requirements, and there is some feeling that the needs of defense might be better met if more funds went into the development of new sources of supply of scarce raw materials and more materials were released to industry at this time. Nonmetallic minerals on the strategic and critical list of the Munitions Board as of July 1951 were: Group I; asbestos, some types; bauxite, refractory grade; beryl; celestite; chromite, chemical and refractory grades; columbite; corundum; diamonds, industrial; fluorspar, acid grade; graphite, some types; kyanite; manganese ore, battery and chemical grades; mica, some types; quartz crystals; rare earths; sapphire and ruby; talc, steatite, block; and Group II; bauxite, abrasive; cryolite, natural; diamond dies; graphite, crystalline fines; iodine; mica, muscovite block, stained and lower; rutile; selenium; talc, steatite, ground; zirconium ore, zircon. Details on the current status of stockpiling inventories are not available. The Defense Minerals Exploration Administration has, since April, executed 39 contracts for the exploration of nonmetallic minerals, including twenty for mica, seven for beryl-mica, six for asbestos, three for sulphur and one each for monazite, steatite talc and fluorspar. Total value of these contracts came to $892,059, of which the Government's participation amounts to $689,247. There were on hand at year's end another 97 applications for exploration aid on nonmetallic minerals in twenty different

Jan 1, 1952

By Josée Dartois

En 1988, à l?instar de plusieurs états du monde industrialisé, le Québec décidait d?accélérer la cadence de l?assainissement des rejets industriels et lançait un programme intégré de réduction de la pollution industrielle visant, à la fois, les rejets dans le milieu aquatique, les émissions atmosphériques et les matières résiduelles. Ce programme fut intitulé le Programme de réduction des rejets industriels.

Nov 1, 2002

By Augusto Cabrera La Rosa

El presente trabajo revisa el panorama sobre el proceso de clasificación y explotación de los recursos minerales no metálicos en el Perú, con el objeto de promover el desarrollo de la minería no metálica. Los metales de origen mineral se clasifican en cuatro grupos: metales en estado nativo y minerales metálicos, combustibles minerales, aguas subterráneas y un gran número de sustancias minerales que no están comprendidas en ninguna de las categorías mencionadas, y que constituyen el grupo de los no metíllicos, llamados también minerales y rocas industriales. Asimismo, se muestra la clasificación establecida por el código de minería (combustibles minerales, minerales industriales, refractarios, material de construcción y minerales no metálicos diversos). Luego se describe el valor de la producción nacional de minerales no metálicos, como la situación actual de la minería no metálica en el Perú. Concluyendo que el Estado debe priorizar la prospección de minerales no metálicos de acorde a la importancia del desarrollo del país, asi como estimular la iniciativa privada para el descubrimiento de nuevos depósitos de dichas sustancias comercialmente explotables.

Aug 20, 1963

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By Leon Eliel

TEN years ago a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these isolated bits of infor-mation can be ascertained, the message begins to take meaning. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of, a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern .he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

By H. H. Fields

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pittsburgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No.2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By H. A. Baumann, C. C. Wright, T. S. Spicer

A LTHOUGH the efficiency of coal utilization has A improved steadily since the turn of the century as a result of continued research and development, little of this increase in efficiency can be credited to improvements in the single retort stoker. There are still numerous problems connected with the burning of coal on this type of unit, the solution of which would be a stimulus to coal and stoker sales and a boon to the user. Among the more critical of these problems is that of burning slack bituminous coal of strong caking tendency and containing large percentages of fine material. With the increased trend toward mechanical mining, it may be expected that in the future an even larger percentage of the coal available for use on this class of stokers will contain higher percentages of the fine sizes, thus aggravating an already serious problem. During the war, the problem of efficient and economic burning of available coals on the single retort industrial stoker, particularly the class 4 stokers (301 to 1200 lb per hr), became quite critical in many localities. In addition to the inherent problems associated with the use of this class stoker, the coals available were frequently not those best suited for use on this equipment and the manpower shortage made it difficult as well as expensive for the consumer to provide the labor necessary to keep the iires in reasonably satisfactory condition. Although exact figures on the number of class 4 stokers are not available, the yearly tonnages of coal consumed are of considerable consequence and have been estimated* at between 15 and 20 million the stoker research staff of the Mineral Industries Experiment Station of The Pennsylvania State College was requested to study the performance of the single retort industrial stoker and to undertake a program of research on the more efficient burning of bituminous coal on this class of unit. Various aspects of overall problem have been investigated since the inception of this program in 1942, only one of which is here reported. General Considerations There are numerous factors which appear directly or indirectly to affect the overall performance of bituminous coal underfeed stokers, such as the caking or matting properties of the coal, the contact relationships between coal and air, the ash fusion characteristics, the burning rate, and the design of the stoker and furnace in which the coal is burned. An analysis of the influence of each of

Jan 1, 1951