Search Documents

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By Hiram C. Draper

The Mining Division of the Bureau of Mines, in cooperation with the Obstacle and Demolition Branch, Engineer Research and Development Laboratories, Department of the Army, undertook some extensive tests to determine the effectiveness and limitations of using standard demolition-type shaped charges in underground Mining. The tests proved the shaped charge has no practical application in the functions of mining covered by this report. At an approximate cost of 0 per foot hole plus spall produced by the most efficient single shots with the M3 shaped charge, the cost is over 20 times that of producing a better hole with a rock drill. The concussion would prohibit its use in many mines, and the excess carbon monoxide gas liberated by the pontolite explosive would be an additional hazard when used underground.

Jan 1, 1948

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By Janeir Ribeiro Dutra

Os aços siliciosos de grão orientado (GO) e de grão não orientado (GNO) são aços ligados ao silício para aplicações elétricas. O aço silício de grão orientado possui as propriedades magnéticas otimizadas na direção de laminação, enquanto o de grão não orientado apresenta boas propriedades em qualquer direção. O aço elétrico de grão orientado tem como principais características as excelentes propriedades magnéticas, desenvolvidas especialmente para a redução das perdas magnéticas e aumento da eficiência de máquinas elétricas. Durante o processo de elaboração do aço o principal desafio é o controle de elementos como alumínio, titânio e enxofre, elementos estes provenientes da carga metálica (sucata e gusa) e adições de ligas na panela. Para este controle ser eficaz a estabilidade da composição química da escória na metalurgia secundária é de fundamental importância. O fluxo produtivo do aço GOAT na metalurgia secundária inicia-se no processo VOD(Vaccum Oxygen Decarburization) com término no forno panela. Este trabalho promoveu a adequação da escória da metalurgia secundária do aço GO através da: i. revisão do padrão de consumo de fundentes, mediante estudo de balanço de massa; ii. desenvolvimento de escória sintética para ajustar finamente a basicidade da escória. Os estudos de balanço de massa apontaram que em determinadas situações havia a necessidade da correção da escória para aquecimento no forno panela; iii. implementação de amostragem de escória ao final do processo VOD para correção da basicidade de escória para aquecimento no forno panela; iv. criação de modelo para correção da basicidade da escória. Após a implementação do projeto o controle da escória no forno panela ficou mais efetivo promovendo: i. redução dos teores finais de alumínio e titânio ao final do processo de elaboração no forno panela; ii.possibilidade de correção da quantidade de escória para aquecimento no forno panela sem comprometer a basicidade de escória requerida no processo; iii. atendimento a faixa otimizada do aço GOAT (M3, maior qualidade) passou de 33% para 65%; iv. redução do desgaste de panelas na elaboração do aço GOAT na metalurgia secundária; v. redução do risco de sucatamento por fora de faixa em alumínio e titânio do aço GOAT na aciaria que representou nos últimos 4 anos uma perda ao processo superior a R$ 1,2 milhão; vi. estabilização da basicidade binária da escória final do Forno Panela dentro da faixa desejável.

Oct 30, 2017

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By Richard Thomas Newcomb

The trend towards proportionately rising volumes of surface mining through- out the world and especially in the United States has led some observers to predict that the future of underground mining is quite limited. Certainly, the simple extrapolation of current trends1 gives evidence of a compelling sort for the hypothesis that technological progress is proceeding at a faster pace in surface than in underground mining. This paper attempts to examine the basis for these predictions by searching the historical record on differential rates of productivity as these are observed in iron ore and coal mining. In recent years economists have discussed "technology gaps" among industries or segments of the same industry, by which they mean that mechanisms for invention and its diffusion are faulty or retarded in such a way that feasible cost-cutting innovations are not applied or developed, even though technicians regard them as practical.2

Jan 1, 1968

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. Tile abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources:

Jan 1, 1963

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine vas evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, and a previously described/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming; and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive Physical and chemical apparatus. Following the termination of this study of chronic poisoning, possibilities ides for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals rich the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By Kim Lapakko

Increasing public concern over the welfare of the environment has placed demands on the mining industry to evaluate the environmental impact of mining development. This is a difficult task and involves considering the influence of a multitude of variables on complex processes over a long time period. Few studies which focus on the evaluation of the environmental impact of mining have been conducted and, therefore, there is little past experience to rely upon. This article describes some of the work done to evaluate the potential environmental impact of mining development in Minnesota. Interest in developing the major copper and nickel sulfide deposits near the wilderness areas of northeastern Minnesota aroused concern regarding the environmental impact of mining development in the region. As a result laboratory and field studies were initiated to investigate the potential for trace metal leaching and acid generation due to dissolution of Duluth gabbro. Chemical equilibrium computer modeling was conducted to aid in data interpretation. The goals of the study included the investigation of leaching mechanisms and rates of release (1, 2).

Jan 1, 1980

By Joan C. Biordi

A molecular beam-mass spectrometer-low pressure flat flame apparatus has been constructed for the purpose of examining the chemical microstructure of normal methane-oxygen-argon flames and those inhibited with Halon extinguishants. Details of construction and performance of this apparatus and of related flame temperature measurements are given. Particular attention is paid to the empirical characterization of the perturbation to the flame caused by the sampling probes. The composition profiles obtained for normal flames are compared to those of flames inhibited by CF3Br. In addition to the usual stable species (CH4, O2, CO, CO2, H2O, H2, and H2CO), the inhibitor, its products and intermediates associated with its reactions could be followed. In particular, hydrogen bromide, bromine atoms, hydrogen fluoride, and carbonyl fluoride were observed. The relatively rapid disappearance of inhibitor and early appearance of fluorinated reaction products suggest a short lifetime for the CF3 radical in this system. Observation of COF2 suggests that CF3Br is effective as an inhibitor, at least in part, by virtue of its interference with the oxygen containing species of the normal chain reaction. Profiles of the 17+ peak at low electron energy suggests that the hydroxyl radical may also be sampled, but the profiles obtained are not yet sufficiently accurate to determine the effect of inhibitor on this important flame radical.

Jan 1, 1973

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By Miguel Rivera F.

El presente texto señala el origen de las menas del yacimiento de la Quebrada de Tuco (Ancash), las cuales se relacionan con las exploraciones como en la evaluación de un yacimiento ubicado. Este yacimiento mineral está formado por unos mantos y vetas de sulfuros, con valores de plata magnesio, zinc, plomo y cobre, acerca del cual se han pronunciado algunos geólogos con opiniones diversas. Para ello, se realizó una investigación mineralógica a nivel microscópico, que se relaciona con la información que evidencia sobre el origen del yacimiento y su relación con diversos fenómenos geológicos.

Sep 1, 1985

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957