Search Documents

By Edward W. Parsons

To determine in what part and to what extent creep or movement exists in an installed rock-bolt anchor and the effect of the creep or bleedoff on the tension load on a rock bolt, as well as the effect of normal mining activity on the rock-bolt load and anchor, the Bureau of Mines conducted tests in the laboratory and in two mines using four types of expansion-shell anchors, the wedge bolt, and in one mine, explosive-anchored rock bolts. Specially mounted heavy-duty springs, calibrated to obtain load readings from spring movement, were installed on the test bolts to prevent a drastic reduction in tension load caused by slipping or seating of the anchor. A dial gage, reading to 0.0001 inch, measured movement of the anchor shell against the rock and seating of the anchor wedge plug in the shell. While all bolts had electrical resistance strain gages for load reading, only readings from the laboratory tests were used because those from the field tests were erratic. The tests revealed that most load loss resulting from static loading is due to the slippage and seating of the serrations on the anchor shell into the drill-hole wall. Dynamic loading, primarily from sudden shocks from nearby blasting, and possibly from ground movement or mining activity, will cause the anchor wedge plug to seat in the anchor shell.

Jan 1, 1969

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By G. W. Josephson

JUDGING by the progressive atmosphere prevailing in the nonmetallic mineral industries during the past year, postwar conditions were healthful though inflationary. Demand for most industrial mineral products has been exceptionally high and many new production records were attained. Severe shortages of some commodities existed, especially building materials and fertilizers. Production costs and prices increased and profitable operation was general. Under these conditions expansion programs were the order of the day. Ample funds were available to finance the purchase of good equipment; and, as wages and other operating costs were increasing, primary emphasis was placed on attaining maximum efficiency in new installations. These efforts were hampered by shortages and slow delivery of desirable equipment, so compromises in design were often necessary. However, on the whole, production practice improved.

Jan 1, 1948

By J. E. Johnson

IT is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence in these respects on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control; the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in d practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the toll-gases, and that the ratio of CO to CO., will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Sep 1, 1905

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By N. Lock

"Despite the pre-eminence of the Jwaneng Diamond Mine as the world’s richest diamond mine, the discovery story has long been clouded in mystery. This is the 45-year old untold story of the Jwaneng discovery and contemporaneous Bechuanaland/Botswana political and socioeconomic history. Diamond exploration by De Beers in Bechuanaland began in 1955, with the first true kimberlite discovery near Letlhakane in 1967, before Clifford’s Rule was applied and before the use of indicator mineral chemistry. Surface deflation soil sampling and bioturbation by termites was the foundation for exploration into the Kalahari. The 1962 reconnaissance programme south of Jwaneng had failed to make any discoveries. Improved sampling methods were applied to the Kalaharicovered areas in 1969 and positive results were received by year-end. The Whateley’s Wish percussion drill-hole in December 1972 was confirmed as Jwaneng 2424D/K2 with drill core in early 1973. Jumper drills were required to penetrate the Kalahari sand cover. Diamond resources were demonstrated despite multiple technical problems. IntroductionThe Jwaneng Diamond Mine is, by value, the world’s richest diamond mine. Harry Oppenheimer is quoted as saying that Jwaneng is ‘the most important primary deposit found anywhere in the world since the discovery at Kimberley more than a century ago.’ (Taylor III, 1982) The mine opened in 1982 after some nine years of evaluation and construction since discovery in February 1973. Debswana (2017) states that 2015 production was 7.87 Mt of ore from which 10.408 million carats were recovered at a grade of 132 carats per 100 t (cpht). Although the value is not reported, it was noted that Jwaneng contributes 60–70% of Debswana’s total revenue from all mines, including Orapa, Damtshaa, and Letlhakane (Debswana, 2017)."

Feb 1, 2019

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

By Jr. Moulton

Extractions of minerals from Searles Lake brines have taken place since 1873. Early operations were for borax and raw trona found on the surface, expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of Eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1980

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

By H. R. Shell

The work on synthetic mica and related subjects is being reported in a series of technical articles (see Supplementary Bibliography), each of which describes some special aspect of the subject. This is the final report on chemical analysis of the fluoride-containing silicates. A condensation of this report has been published (26).3/ Chemical analysis affords one of the best means of ascertaining the final com-position of either a heterogeneous mass or a single pure crystal, particularly where some constituents may be volatile. The analysis of fluoride-containing silicates was not so well known or understood that highly accurate results were commonplace. For example, on synthetic mica a university laboratory reported 11.6 and 9.2 percent fluoride when at least 13.3 and 11.3 percent were present, respectively; a commercial testing laboratory reported 9.14 percent as compared to 12.6 percent; and a glass company reported 7.0 percent as compared to 9.0 percent present. No intimation is made that these analysts could not have done better, but the point to be stressed is that the methods in use were long, tedious, and generally required a certain familiarity for best results.

Jan 1, 1956

By C. A. Komar

The Bureau of Mines is investigating possible applications of acoustic energy at sonic and ultrasonic frequencies in petroleum production. A phase of this work involves measuring sound velocity through petroleum reservoir rocks. References and abstracts were prepared as a bibliography to make available to others some of the material obtained from a literature search covering the past applications and the present uses of sound. Laboratory and theoretical studies of the various parameters that influence the velocity of sound in porous media account for the wealth of information now available. Velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity logging systems, capable of measuring speed of sound waves in underground formations penetrated by wells, have been developed for interpretative studies. The close relation between acoustic velocity and porosity makes it possible to determine porosity from velocity logs. Most velocity log interpretation in terms of porosity is based on a formula developed by Wyllie and others known as the time-average relation.

Jan 1, 1963

By H. R. Hardy

Whether the mining engineer is concerned with stress problems in a mine at depth, the development of a new drill bit, or the efficiency of a comminution process, the mechanical properties of the rock with which he must work are of the utmost importance. One of the most popular topics in rock mechanics circles today is ?Is it possible to utilize directly parameters determined from laboratory tests on rock specimens in the analysis of mining engineering problems?? It is the author's opinion that laboratory and .field investigations have not yet reached the stage of development where this question can be answered with any degree of certainty. At present, great difficulties are involved in applying the results of laboratory tests to a mining engineering problem. However, this is due in part to the lack of detailed measurements of stress and deformation in the field and in part to the lack of development of satisfactory structural theories to correlate laboratory and field measurements. Furthermore, if mechanical properties measured in the laboratory are to be directly applied to the analysis of mining engineering problems, the critical mechanical properties must be identified, reliable test procedures must be developed and extensive test programs must be carried out.

Jan 1, 1964

By Alberto Hurtado

El presente texto refiere los aspectos fisiopatológicos y clínicas que comprende un ambiente de mayor altitud para el organismo, así como que las dificultades en la adquisición, transporte y utilización de oxígeno son comunes a muchas enfermedades y procesos patológicos.

May 1, 1975

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By R. M. Parlman

Interest is increasing in obtaining incremental improvements in mineral recoveries in flotation processes because of changing world economic conditions. Research on collector reagents, long indispensable components in flotation systems may provide the cheapest and simplest route to higher metal recoveries. Sulfhydryl group - containing compounds (-SH) and their salts, e.g., dithiophosphates, xanthates and a few other derivatives are commonly used to promote the flotation of sulfide minerals. Alkyl mercaptans, another class of sulfhydryl compounds, have long been known to have collecting properties but have been relegated to dormancy for one reason or another. This paper reports results from new investigations of alkyl mercaptans, trithiocarbonates, and a petroleum oil with a variety of western domestic and Canadian ores for copper and molybdenum sulfides recovery. Specific opportunities are pointed out to the industry for mineral recovery enhancement through the use of the proper reagent combination.

Jan 1, 1980

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939