Search Documents

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep sandstone in the Elk Basin field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes of gas in solution, saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep reservoir of the Elk Basin field has unusually varying physical characteristics, such as a saturation pressure of 1,250 pounds per square inch absolute and 490 cubic feet of gas in solution in a barrel of oil at the crest of the structure, and a saturation pressure of 530 pounds per square inch absolute and 134 cubic feet of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the 6a r; in solution in the oil varies from 18 percent for oil on the crest to 5 percent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of oil in the structure. Many geologists and petroleum engineers have considered all the oil in a petroleum reservoir to have uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas. That such is not always so is borne out by the results of the study made by the writers.

Jan 1, 1951

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940

By Dale Ramsey

During Phase IV of our Landfill Mine Stabilization project at a coal burning power generating station, it was determined that a coal barrier pillar separating two abandoned areas of the deep mine had to be breached prior to expansion of the ash disposal area. The proposed plan by the landfill design engineers involved using a high pressure jet cutting tool to cut a slot to allow water flow to an existing industrial waste water treatment facility. Our plan proposed using explosives to breach the pillar from the surface reducing earth disturbance in a high quality watershed while reducing the project cost and accelerating the project time schedule. Many issues surfaced with the proposed change of using explosives. There were a number of lessons learned from this case history and is the primary basis of this paper.

Jan 1, 2003

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By N. E. Maccallum

(Cleveland Meeting, October, 1912.) ALMOST half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: ?What is the safe and economical limit of the open-hearth furnace?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own Conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Co., of Phoenixville, Pa., and their distinctive and important feature is, that they charge to twice the capacity of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Oct 1, 1912

By Robert H. Ridgway

This circular outlines salient facts regarding the sulphur industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. It will welcome comments, criticisms, and contributions of data that may assist in making later editions of this circular more accurate, or in developing more fully the bureau's mineral files pertaining to sulphur. Throughout this paper sulphur is used to designate crude sulphur or brimstone, not sulphur produced from pyrites or' smelter gases.

Jan 1, 1930

Table 1.-Salient aluminum statistics (Thousand short tons and thousand dollars) [ ]

Jan 1, 1967

By M. F. Koehler

[THE LITERATURE contains relatively few thermodynamic values for interoxidic compounds, and these often are unreliable. This is especially true of data for ferrites and aluminates for which heat of formation determinations may involve extreme experimental difficulties. This report contains the results of new experimental work for obtaining the heats of formation of five ferrites (Ca2Fe2O5, CaFe2O4, MgFe2O4,, NaFeO2, and LiFeO2) and one aluminate (CaAl4O7), and a review and revision of previous similar work of this laboratory on five aluminates (Ca3A12O6,, 12/7 CaO-Al2O3, CaAl2O4, NaA1O2, and LiAlO2), The results for the 11 compounds are combined with entropy and high-temperature heat content data to derive tables of heats and free energies of formation (both from the oxides and from the elements) for the temperature range 298° 1,800° K, The relative stabilities of the compounds are discussed. The presented data all have application to ceramic reactions, and those for the calcium and sodium aluminates are applicable in considering soda-lime sintering processes for extracting alumina from silicate minerals such as day and labradorite.]

Jan 1, 1961

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By Himmelman. Nicholas P.

In this paper, the hardware foundations and data collection methods of a real time collision avoidance system for electric surface mining rope shovels are described. The primary goal of the system is to help a shovel operator avoid accidentally colliding the shovel?s dipper with either a nearby haul truck or the shovel?s tracks. To achieve this goal, the system requires complete and precise knowledge of the shovel?s geometry and movement, as well as the location of any nearby haul trucks. This paper describes the subsystems created to acquire this necessary information. This system is unique in that all of its components are mounted solely on the shovel and that it is designed to be easily retrofitted to a shovel without significant modifications.

Oct 1, 2009

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defence for purposes other than the extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallic is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of the Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

"The sulphide nickel resources of Australia are concentrated in the Western Australian Shield. This shield is considered to have developed by extensive, but incomplete, Proterozoic reworking of once-continuous Archaean crust. It now constitutes relic Archaean cratons and intervening orogenic mobile belts transected by narrow, curvilinear tectono-thermal mobile belts of younger Proterozoic age. Remnants of the Archaean cratons are exposed in the Yilgarn and Pilbara Blocks. In the former an ancient (to ca 3600 m.y.) high-grade gneiss terrain (Western Gneiss Terrain) occurs along the western margin of the block and is interpreted to flank younger (ca3000-2800 m.y.) greenstone belts to the east. Ancient (to ca3500 m.y.) granitoid-greenstone terrains dominate the Pilbara Block.Proterozoic mobile belts contain only traces of nickel mineralization, except for one locality in the Halls Creek Province. The Archaean high-grade gneiss terrains contain no important mineralization, and the Pilbara granitoid-greenstone terrains contain only scattered examples of less important types of mineralization.The important deposits (e.g. Kambalda, Windarra, Agnew, Mt Keith) are all of komatiitic affinity and are best developed in the youngest greenstone belts of the eastern part of the Yilgarn Block. In particular, they are concentrated within, and adjacent to, the Norseman-Wiluna Belt, which contrasts in age, lithofacies and structural style with all other greenstone belts in the shield. It is interpreted to have been a rift zone. Within this belt the two main deposit types—the volcanic peridotite-associated and intrusive dunite-associated deposits—are concentrated into spatially separate zones. Precise controls on this heterogeneous distribution cannot be determined unequivocally from available data. One possibility is that the major volcanic peridotite-associated deposits were developed selectively in the actively subsiding axial part of the rift zone during the early extensional phase, whereas intrusive dunite-associated deposits were formed during a subsequent (less active?) stage of volcanic basin development. Distinctive sub-types (facies) of the volcanic peridotite-associated deposits form clusters that are generally within the rift zone. These may represent deposits related to discrete eruption centres, and at least part of their variation is due to relative position within extensive, topographically confined, linear flows."

Jan 1, 1984

By T Ireland

The Rosedale Outfall Project utilised an earth pressure balance (EPB) tunnel boring machine (TBM) for only the second time in Auckland. Although the tunnel was excavated fully through East Coast Bays Formation (ECBF), the downhill gradient along with some unexpected areas of extreme water posed some significant challenges during construction.The Rosedale Waste Water Treatment Plant Outfall Tunnel project was commissioned in response to the growing needs of North Shore City, New Zealand. The outfall tunnel comprises a 3 km long segmentally lined tunnel and a 2.1 km buried marine pipeline, and discharges 2.7 km offshore. The capacity of the new outfall is 6 m3/s compared to the existing outfall capacity of 1 m3/s.Following previous project experience, and with the tunnel located along its full length in the bedrock weak sandstone/siltstone bedrock of the East Coast Bays Formation, tunnelling conditions were expected to be benign. However during construction six high inflow events were encountered, including a full face (3.4 m diameter) of Albany Conglomerate over a 48 m length of tunnel. This material comprised cobbles in an uncemented sand matrix, and inflows were recorded at over 25 L/s.This paper describes the design challenges on the project including the design of a steel fibre reinforced segmental lining for internal pressures. The specification of the machine is discussed including the modifications required to enhance the risk mitigation measures already in place. The ground conditions encountered are discussed and have improved the knowledge of the range of conditions that can be expected in Auckland.Despite the challenges presented during construction, excellent progress rates were achieved and the tunnelling was successfully completed ahead of program.

Mar 8, 2011