Search Documents

By W. F. Faragher

The principal equipment in the catalyst plants at Ludwigshafen-Oppau was inspected and is presented in the form of flow sheets for the manufacture of four of the principal catalysts. The equipment is in many cases of special design rather than stock items that was built by the company and modified in the coarse of the growth of the high-pressure synthesis of hydrocarbons in Germany. It is believed that if the manufacture of catalysts were to be undertaken elsewhere, the selection of equipment for the operations involved could be made successfully from the guidance furnished by this rather general report. Five additional catalysts are described, also. II. CATALYST 5058 FROM FRESH TUNGSTIC ACID In a supply tank of about 2,000 liters capacity, 500 kg. of tungstic acid (W03.H2O) that contains about 92-93 percent of W03 is dissolved at 60-70° C. in 1,500 liters of mother liquor. The solution is-effected by stirring for about 1-1/2 hours. The mother liquor is obtained from a previous, lot of catalyst and is first adjusted to a concentration of 13 percent 1H3 by passing in gaseous ammonia. The solution is allowed to stand without stirring for 1 hour, then is pumped into the saturating vessel through a cloth filter (three-quarters hr. to one hr.). The saturator is purged with H2S and thereafter the solution, which has been cooled to about 75° C., is heated in an atmosphere of hydrogen sulfide with stirring to about 70° C. This charge is slowly cooled to 50°, and then more rapidly to about 20° C. (time of cooling 6-7 hours).

Jan 1, 1946

By Kenneth L. Kreamalmyer

"The demand for open-hearth iron ore and the existence of suitable smelting facilities in the St. Louis area seemed to warrant investigation of several Missouri iron-ore deposits of the filled-sink type. Preliminary examinations were made in the autumn of 1944 by an engineer3/ of the Bureau of Nines, and in December of the same year funds were allotted for the exploration of these properties by churn drilling. Three properties, the Silver Hollow Bank and the Newbauer and Coleman properties, were drilled. Work was completed May 8, 1945.The Federal Geological Survey and the Missouri Geological Survey and Water Resources assisted in the project by determining the stratigraphy from drill cuttings and by mapping the drilled areas.The properties explored are in the hilly section of east-central Missouri and are connected by all-weather graveled roads with various shipping points of the St. Louis-San Francisco Railway system within 3 to 6 miles of each property.The Silver Hollow Bank, in sec., 8, T, 40 N., R. l W. Franklin County, Missouri, is in the Meramec State Game Reserve. The nearest town and shipping point is Sullivan, Mo„ which is 6 miles distant. The Newbauer property, in sec. 28, T. 41 N., R, 2 W., Franklin County, Missouri, is approximately 3 miles west of Stanton; The Coleman property, in sec. 14, T. 38 N., R. 3 W., Crawford. County, Missouri, is within a short hauling distance of the railway at Elayer, Mb. These are shown on figure 1.The region surrounding the explored areas contains a series of low-lying hills or ridges and narrow winding valleys drained by the Meramec River system. These hills seldom rise more than 200 feet above the valley floors, most of which are approximately 700 feet above sea level. Except for numerous small farms and a few small towns, the entire region is covered by a dense growth of timber and small brush. The St. Louis-San Francisco Railway system, U. S. Highway 66, and numerous all-weather State and county roads traverse the area."

Oct 1, 1945

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978

Orange Free State Branch Minutes of a Committee Meeting held in the Boardroom of Western Holdings on Thursday, IIth October, 1973, at 5.00 p.m. Present Messrs E. T. Wilson (in the Chair), E. Dunstan, W. B. Evans, C. J. Isaac, C. Mostert, N. Shand, R. Williams, and G. Young.

Jan 2, 1974

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By William L. Crentz

This study of the preparation characteristics of the coals in Indiana County, Pa., is the second in a series of Bureau publications appraising the Nation's coking-coal reserves by counties and the practicability of upgrading marginal deposits to metallurgical standards. The first publication dealt with the preparation characteristics of the principal coal beds in Cambria County, Pa. Over 95 percent of the coal remaining in Indiana County is in the Upper Freeport, Lower Freeport, and Lower Kittanning beds. Isolated patches of Pittsburgh-bed coal are present, and the Upper Kittanning bed is found in minable thickness at some locations, but production from these sources is not large. The greatest production is from the Freeport beds, which account for nearly 70 percent of the Indiana County coal output. These beds usually contain two or more shale or hone partings and in many places are high in sulfur. The large proportion of bony coal in the Freeport beds 'produces a relatively high-ash product. Mining practices vary from place to place, but it is frequently necessary to leave certain bony portions of the bed in place in order to load a satisfactory product. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1951

By Gordon Bath

During the summer of 1946, the Division of Geophysical Exploration of the U.S. Bureau of Mines established several primary magnetic base stations near important iron-producing districts in Minnesota, Michigan, and Wisconsin. Stations were located in groups of four to six in six separate base-station areas, and each position was marked with a concrete monument. Differences in magnetic intensity between stations in these areas, as well as the difference between each area and a magnetic datum at the magnetic observatory of the Coast and Geologic Survey at Cheltenham, Md., were measured with a modified Askania magnetometer. Measurements also were made with a Hotchkiss superdip to study the usefulness of the stations for the calibration of instruments of this type. The work was planned and supervised by F. W. Lee, chief of the Division of Geophysical Exploration, and Edward F. Fitzhugh, Jr., chief of the Minneapolis Division of the Bureau of Mines. Special mention is due Harold B. Ewoldt, Bureau of Mines engineer, for his assistance in the field work, especially in locating and establishing monuments. Special mention also is due Clyde L. Holmberg, of the Bureau of Mines, for the magnetic measurements made with the Hotchkiss superdip. Helpful suggestions were received in the field from H. L. James, of the U. S. Geological Survey. Acknowledgment is made of the cooperation of Stephen Royce, Irving E. Beckwith, Arthur Johnson, and Josiah Royce of Pickands, Mather & Co., and A. E. Matson, of Butler Bros. The U. S. Coast and Geodetic Survey furnished daily magnetograms from the Cheltenham Magnetic Observatory as well as calibration equipment and values of absolute magnetic intensity. Short-term forecasts of ionospheric conditions were obtained from the National Bureau of Standards.

Jan 1, 1951

By E. Watkins, J. C. LeRoy, A. Vivyurka

"TAILINGS REVEGETATIONWelcome to the Revegetation Session. My instructions are to introduce the Speakers and to provide a general introduction.I do the latter with humility not only because of a lack of personal experience or because tailings revegation is not well established technology, but because any general statement on a country or industry as diverse as the Canadian Mining Industry is bound to be wrong somewhere.Laying aside normal standards of accuracy I proceed as follows:In considering the question of tailings revegetation, one asks two basic questions:1. What ought to be done?2. What can be done?The first question can be broken down into three kinds of criteria or objectives:a) Legislativeb) Technicalc) AestheticThe first I leave to the politicians and the last I will avoid. Aesthetics is the philosphy of taste. It is concerned with the appreciation of things rather than what they really are. It is much easier to get into an argument on aesthetics than to get out of it feeling you have said something of consequence.Technical criteria can be divided into the following sub-objectives: 1. To isolate the tailings basin so surrounding land is not degraded. The first step here is stabilization of the surface to prevent wind and water erosion."

Jan 1, 1975

By A. K. Biswas

Reviewer: R. H. Eric This edition is organized in twenty-three chapters, and contains exactly 500 pages including three appendices and an index. The first and second editions were published in 1976 and 1980 respectively, and both contained nineteen chapters. The second edition brought the operating data and process descriptions up to date. The third edition covers comprehensively the changes that have taken place in the primary copper industry over the past two decades. For example, reverberatory furnaces now make up only a third of the major primary smelting furnaces, compared with about three-quarters in the 1970s. Control of air and water pollution and recycling are given much more emphasis, along with novel and emerging technologies.

Jan 1, 1995

By Jephcott S

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralized bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulphides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralization. The geochemistry of the deposit has been investigated with respect to the stratigraphio column and mineralogy of the sediments.

Jan 1, 1980

By N. L. Dorset, K. L. Heasley

Unfortunately, mining and mining accidents have gone hand-in-hand since man first started to extract ore from the ground. In the first published treatise on mining, De Re Metallica, Georgius Agricola (1556) stated that cold, water, dust, stagnant and foul air, roof falls, falls from ladders and demons all caused injury and death in the mines of his day. Although demons are no longer considered a cause of accidents in modern mining, the other factors remain with us still. The United States government started keeping track of fatalities with the establishment of the federal Bureau of Mines in 1910. Successor agencies, such as the U.S. Mine Safety and Health Administration (MSHA) continue to track fatalities today. Looking at the records, it can be seen that coal mine fatalities dropped from 2821 in 1910 to only 27 in 2004. The reduction in fatalities and injuries didn’t “just happen.” It took concentrated effort from the entire mining industry: miners, supervisors, safety officials, mining inspectors and mining researchers. But first, specific hazards must be identified before they can be corrected. In past, coal mining accidents have been analyzed by: type (roof fall, electrical, etc), mine attribute (location, seam height, etc.), and aspects of the mineworker (work experience, job classification, etc). Much of this research helped to direct the industry’s attention to where additional vigilance and safety training was needed. No doubt this directed effort has led, at least in part, to the decrease in coal mining fatalities. This paper takes a novel look at coal mining fatalities: it examines the risk of fatalities based on how long the mine has been open.

Jan 1, 2006

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

By T. Yeomans

NVI Mining’s Myra Falls operation is a forty-year-old underground mining operation feeding a 4,000 metric tonnes per day concentrator. The current mill, built in 1985, was designed to process a massive sulphide ore-body. This orebody, known as the HW, contains about 50% pyrite. Minerals of value are chalcopyrite and sphalerite, with precious metals occurring in all mineral types. By 1997, mining of a new ore-body, known as Battle-Gap, commenced. Mineralogically complex, the new orebody contains about 15% pyrite copper minerals, including primary chalcopyrite and secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite. Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected. Following significant metallurgical test-work, a new, fully sequential copper-lead-zinc flotation flow sheet and reagent scheme was developed. This sequential flow sheet was progressively installed and commissioned during 2006. Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, while increasing copper recovery by 10%.

Jan 1, 2009

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950

By Linda Hodgson

1. Introduction ?Northgate Minerals Corporation is a mid-tier gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. ?Kemess Mine is Northgate?s principal operation. Where in the world is Kemess? ?Kemess is located in north-central British Columbia,430 kilometres northwest of Prince George. ?The Kemess South complex consists of an open-pit mine, a 52,000 tonnes per day mill and various ancillary support facilities including maintenance shops and housing for Kemess' 340 full-time employees.

May 1, 2010

By Villanueva G. Julio

El presente trabajo describe el método de muestreo para la evaluación y cubicación del tajo a cielo abierto en Cerro de Pasco. Para ello, primero se describe la geología general de la zona de Cerro de Pasco para conocer y resolver los problemas encontrados en la explotación, encontrándose una irregularidad en la distribución de valores, como en la concentración de minerales. En consecuencia, se elaboró una serie de medidas que respondan al sistema de evaluación utilizado, tales como: la necesidad de efectuar una reevaluación de la zona en cuestión, el remuestreo de la mina, la impracticabilidad de hacer una exploración a través de sondajes, el empleo de algún medio mecánico para la extracción de las muestras, la implantación de un sistema especial para el archivamiento de los resultados de los ensayos y así evaluarlos rápidamente, y la necesidad de conocer los pesos específicos de los diversos tipos de minerales concentrados para calcular el tonelaje con precisión.

Jul 20, 1960

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938