Search Documents

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By Marcello Crispi, Valdir Silva, Juarez Moraes

Companhia Vale do Rio Dote - CVRD is the largest mining company in Brazil and the largest iron ore producer in the world. Serra Geral Mine (SGM) is located at Iron Quadrangle of the State of Minas Gerais, approximately 80 kilometers from Belo Horizonte. Hematite and Itabirite are the two main minerals. A blasting with a spherical charge has been introduced at Serra Geral Mine, an iron ore producer in Brazil, belongs to the CVRD (51%) Kawasaki Steel Corporation (24.5%) others (24.5%), in order to improve fragmentation, as well, load, transportation and crushing productivity. This paper will present the results of a successful blast design with a spherical charge carried out by Serra Geral Mine, the Department of Mining Engineering at Escola de Minas - Federal University of Ouro Preto-UFOP associated to a Blasting Engineering Consultant. The results obtained in the field tests and how it was possible to increase the blast pattern in 53%, which allowed one reduction around 31% in the cost of blasting operation in the Serra Geral Mine, will be discussed in details.

Jan 1, 2002

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By Gerhard Nel, Huziel Masiiwa, Marthie Kotze, René du Preez, Simon Donegan

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology, to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when it is attempted to maximise the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory test work was conducted on the raffinate of the cobalt solvent extraction circuit to optimise the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimised in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory test work results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By Lauri Gregg

Key Message Energy focused Change Management Process that engages operations managers is the missing tool needed to build capacity for energy/GHG management

May 1, 2007

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By A. E. Fiorato

A test program was conducted to evaluate use of high-strength concrete in drilled shafts (caissons). The objective of the program was to determine if internal temperatures developed during cement hydration, or other characteristics of high-strength mixes, affect in-situ strength and stiffness. This paper covers strength results. Two 10-ft (3.0-m) diameter by 40-ft (12.2-m) deep caissons were constructed using two different commercially available high-strength concretes, a "low-heat" and a "high-strength" mix. Measured 6x12-in. (150x300mm) moist cured cylinder strengths at 56 days were 13,690 psi (94 MPa) for the "low-heat" mix and 17,130 psi (118 MPa) for the "high-strength" mix. Compressive strengths and moduli of elasticity of cores taken from the caissons were compared to those of companion cylinders made during casting of the caissons and stored in a moist room. Strengths of 4x8-in. (100x200 mm) cores taken at four ages and tested between 34 and 398 days averaged 81% of strengths of 6x12-in. (150x300 mm) moist cured cylinders at corresponding ages. In-situ (core) strengths of the caissons did not appear to be measurably affected by temperature. However, the data indicate that core strengths were sensitive to level of consolidation, as reflected in entrapped air voids. Overall, the results indicate that high-strength concretes can be used in drilled shaft (caisson) foundations.

Jan 1, 1991

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, The United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Norway, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By Kenneth Eltschlager

Business says that location is a primary component of being successful. So too is the importance of location in blasting. For blast seismograph data to be useful, the location of the blast and seismograph must be clearly documented. Another location of importance is that of a nearby structure. Establishing the spatial relationships between the blast, seismograph and nearby structures, allows the blaster to correctly interpret the data, evaluate the performance of the blast and gauge the validity of any complaints.

Jan 1, 2004

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By D. Harrington

In this period of generally increasing taxes of various kinds, one hears less complaint by mining companies about the high cost of workmen's accident compensation than was the case a few years ago, the reason perhaps being that other and more pressing phases of the tax problem now over shadow the heavy expenditures for compensation premiums which a few years ago were considered a severe burden on the mining industry. Nevertheless, the financial expenditures of the mining industry in higher compensation benefits and hospitalization or in higher premium rates, or both, instead of being less have actually increased in many States in the past year. In the spring of 1937, proposals for increased benefits to injured employees in compensation, hospitalization, or medical aid were actively before legislatures in California, Connecticut, Georgia, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Massachusetts, Michigan, Minnesota, New Mexico, Oregon, Pennsylvania, South Carolina, Texas, Utah, Washington, Wyoming, and possibly other States. In some cases, the proposed increases in benefits were so much greater than expenditures for similar items in the past that premium rates per $100 of payroll would almost certainly rise sharply. At this same time, occupational-disease-compensation coverage also was under consideration by legislatures in Arkansas, California, Delaware, Idaho, Indiana, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah, and Washington. Sooner or later (and probably within the next few years) occupational-disease compensation will be accorded practically as wide recognition as accident compensation receives at present, and, unquestionably, mining in all of its branches will be affected more or less drastically. Hence, the present outlook is that the mining industry, in company with practically all other industrial activities, will be confronted by materially higher compensation costs than those of the past or the present, to which rather violent exception has been taken, at least in some States and at some times.

Jan 1, 1938

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011