Search Documents

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Elk Creek RARE II area during the summer of 1981. The study area encompasses 18,900 acres [29.5 sq mi (7,680 ha)] along Elk Creek, 18 mi (30 km) southeast of Covello, California. No mineral resources were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese and chromium. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

Estimating Breakage of Fine Ore Particles by Media in a Small Ball Mill Using DEM

Sep 13, 2010

Jan 1, 1967

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

The Effects of Collector and Grinding Environment on the Flotation Selectivity of Rosh Pinah Pb/Zn Ore

Sep 13, 2010

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By R J. Worland, D Bowyer, J L. Mauk

The TerraSpec is a compact field portable mineral analyser that uses non-destructive reflectance spectroscopy for mineral identification. The instrument uses and measures infrared and visible light that is absorbed by certain covalent and molecular bonds (AlOH, FeOH, MgOH, CO32-, OH, H2O and NH4) within the lattice of a mineral at specific wavelengths producing an absorption spectral profile. A variety of minerals can be detected including clays, micas, carbonates, and hydroxides as well as some sulfates and silicates. However, not all minerals are detectable, such as quartz and feldspar. Alteration minerals replacing volcanic rocks have been studied for several epithermal prospects in the lower Waitekauri Valley (Sovereign, Jubilee, Scotia and Jasper Creek) and a geothermal field in the Taupo Volcanic Zone. At the Sovereign, Jubilee, Scotia and Jasper Creek prospects previous XRD investigations determined well developed clay mineral zonation with illite in the west (Sovereign and Jubilee) grading into interstratified illite-smectite (Scotia) and smectite (Jasper Creek) to the east. Although the percent of illite within interstratified illite-smectite could not be determined and some illite-rich illite-smectite (>90 per cent illite) and some smectite-rich illite-smectite (>90 per cent smectite) could be misidentified as illite or smectite respectively, the TerraSpec survey determined the same zonation of illite to illite-smectite and smectite. Common chlorite, rare calcite and local kaolinite were also detected. At the geothermal field, the TerraSpec was primarily used to determine the occurrence of kaolinite, dickite and alunite, which form in acid conditions. Widely spaced (every 50 to 100 m) XRD results are in excellent agreement with closely spaced (every 5 to 10 m) TerraSpec results that further determined the occurrence of these minerals in previously unrecognised intervals. It also determined the occurrence of zoned smectite, illite-smectite, illite, and chlorite alteration. Overall, the TerraSpec is a rapid mineral identification technique that is very useful in delineating the occurrence and distribution of certain minerals in both epithermal deposits and geothermal fields. Although the TerraSpec cannot detect as many minerals as XRD, the TerraSpec allows data collection at a sampling scale and speed (real time) that is not practical by XRD.

Jan 1, 2006

By Q. Lui, J. Oxenford

The occurrence of heavy minerals in the oil sands of Alberta has long been known and has been well documented in the literature. Unfortunately most of the researchers working on this resource have been unable to produce products that meet acceptable market specifications. This has resulted in many misconceptions about this resource. Recent efforts have shown that with some innovative approaches, marketable material can be produced and as a result it might finally be possible to realize the potential of this immense resource that, some have estimated, could contain in excess of 20% of the world demand by 2010. This paper highlights the uniqueness of this mineral assemblage and the mineral processing challenges it presents. It shows the most recent work that has resulted in the production of marketable titanium and zircon products. This paper also focuses on some of the special problems resulting from the variability in the heavy mineral suite. Of special interest is the occurrence and removal of bitumen and pyrite without adding to the sulphur dioxide loading in the regional airshed. The trend by the mining industry to develop various positions on ‘sustainable mining’ has some significance for the heavy mineral industry. Although the industry generally has an excellent track record of eventually rehabilitating disturbed ground in an acceptable manner, heavy mineral mining operations tend to have a relatively large footprint of disturbance and the industry is under considerable pressure to develop options that are more environmentally acceptable. In addition, as operators move to exploit deposits that are lower grade and/or are further from a port site, the emissions per unit of sold product will also rise and the industry will be under pressure to address this issue as well. Because heavy minerals from oil sands are by-products of existing operations, there are virtually no incremental disturbances or emissions that would be associated with heavy mineral production. All mining and tailings remediation issues are accounted for by the oil sand operation. The only incremental emissions would be those associated with the mineral processing operations and transport of finished products to a port site. This paper discusses the environmental and cost implications of this situation.

Jan 1, 2003

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Daniel Briones

El presente trabajo señala las bases que fundamentan la aplicación de los Sistemas de Gestión Integrados y se ofrecen argumentos que sustentan los mecanismos usados para integrar los sistemas de Seguridad (NOSA), medio ambiente (ISO 14001) y calidad (ISO 9001); y la necesidad de su uso como herramienta de gestión por parte de la organización, llegando a todos los niveles hasta alcanzar la madurez del Sistema. Asímismo, se describen algunos ejemplos del impacto positivo, que ha significado la implementación de este Sistema en la unidad de producción Uchucchacua (cuarta productora mundial de Plata,), desde el inicio del Proyecto, hasta lograr la revalidación de la Certificación de las normas ISO 14001, y la cercana certificación en OHSAS 18001 e ISO 9001.

Sep 12, 2005

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997