Search Documents

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By William L. Young

There is an old saying in Canada: "Mines are made as much as discovered." What follows is Young's perception of his experience developing and financing the Cochrane Hill gold mine project. In 1974, I came back from rutile and zircon exploration and mining in Australia. I became interested in a copper, lead, and zinc project in the Bathurst District, New Brunswick. Much field work had already been done but I was convinced that a reinterpretation of the geophysical work left room to enlarge on the known mineralization. So, with my own money I put a property deal together, found an underwriter willing to raise $100,000, and had a lawyer produce a prospectus. The prospectus was ultimately accepted for filing by the Ontario Securities Commission and I acquired funding and began work. It did not take many drill holes to determine that the interpretation was not geologically valid. However, while drilling was going on, geophysical and geochemical explorations indicated interesting anomalous zones elsewhere on the property. But by now the base metal market climate had soured and the $50,000 I had left was not enough to evaluate the new results. So I decided to farm out the property. A data folio was produced and the property was optioned to a major mining company, with Northumberland Mines Ltd. retaining a 20% free, carried interest. By 1976, the market for junior issues was so bad no under¬writer would even talk to a geologist and I still had the $50,000 in the bank and was looking for something to initiate. A Project That Went Nowhere Market research indicated that the Toronto area imported fine calcium carbonate fillers from Georgia, Alabama, and Vermont. I was aware of the specs and the fact that there is a large marble belt in Eastern Ontario. After some prospecting, I found an interesting deposit. The product was slightly high in silica and low on brightness. Research work eliminated the silica and corrected the brightness. So, with insufficient money we launched a feasibility study. This included diamond drilling, bulk sampling, special fine grinding and air classification tests, and an in-depth market survey. Our product was as good or better than those on the market. Our advantage was that delivery could be made by a two-hour truck haul to the customer. The present system of rail delivery had many problems, especially in winter. Despite everything looking rosy, we ran into a stone wall. The underwriters were singularly unimpressed because the public saw little glamour in a substance most people had never heard of. The issue would have been difficult-if not impossible-to sell. Banks and government agencies took the position that if we could get long term take-or-pay contracts then they would lend the required capital. None of the suppliers, however, would even consider a contract until production had begun and they could evaluate the production material. It was a classic "catch 22" situation. I have gone into this in some detail to show how tough the industrial mineral market can be. We eventually optioned this calcium carbonate property to a major corporation. The option agreement would give us a free, carried 15% and the right to buy up to 40% for contributing 25% of the production costs. But the experience left my company in poor financial shape. To survive, I think the entrepreneur-geologist must always have at least one project in reserve, an emergency plan. I had been searching out a new project to work on, after the calcium carbonate option was wrapped up. It was gold. Gold intrigued me and I knew quite a bit about Nova Scotian gold. I felt that with any rise in price, many of the former high-grade gold mines would have interesting potential for the larger, low grade portions of the deposits. That is how I happened on Cochrane Hill, where much work had been done in the early 1970s when gold as $4.82/g ($150/ oz). This time my timing was good. No sooner had Northumberland signed an option agreement than gold prices started to rise. In six months, they went to $27.331g ($850/oz). Even so, financing gold prospects in early 1980 was still not easy. It had been years since gold financing had been undertaken. A whole new generation of investors, with no knowledge of gold mining, had grown up. So, with accounting and legal council, we decided on a semiprivate "seed money" offering. Under the new Ontario Securities Act, this was a new-and partly tax sheltered-concept. At the time, it was very innovative.

Jan 6, 1982

In the estimation of reserves the known values of the variables of interest from surrounding drill holes are used to compute or estimate the unknown value of the orebody over a given region or at a given point of interest. The classical means of doing this are: 1. The Polygonal Method û where the region is divided into polygons centred on bore holes, each variable is then assumed to have constant value over each polygon. 2. Inverse distance methods, where the variable is assumed to vary linearly with the distance between the known values of the drill holes. 3. Inverse distance squared method û a quadratic variation is assumed for the variables between the bore holes.

Jan 1, 1983

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

By T. T. Read, T. L. Joseph, F. H. Royster

In a preliminary study of the beneficiation of iron ores conducted by the Bureau of Mines, one of the authors (T. T. Read) found it necessary to ascertain, if possible, how much effect a decrease in the silica content of an iron ore has upon the cost of making pig iron from the ore. In the beneficiation of iron ores the most important impurity to be removed is usually silica, and the amount that can be expended on a beneficiation process to reduce the silica content of the ore is obviously determined by the amount of increase in the value of the ore after beneficiation. The price that can actually be obtained for a beneficiated ore is, of course, a matter of negotiation between the seller and the buyer, but since the relative value of different grades of iron ore must be chiefly based upon the cost of making pig iron from them, an approximation as to the effect which decrease in the silica content of ore has upon the cost of snaking pig iron is an important guide in estimating what probable average gain will result from subjecting an ore to a beneficiation process. A search of the literature failed to reveal any detailed statement on this important topic, but fortunately the data are at hand to permit making an approximate calculation of the probable effect. For the purpose of the calculation assume three iron ores with the following composition (natural):

Jan 1, 1924

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area or the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using ?big hole? drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in detail.

Jan 1, 1978

By E. I. Gedgagov, A. V. Tarasov, V. M. Paretsky, A. D. Besser

"Hydrometallurgical technology and equipment have been developed in the Gintsvetmet Institute (Moscow, Russia) for processing of rhenium-containing alloys waste to produce commercial- grade metal products with recovery of all valuable components. The technology is based on waste treatment with hydrofluoric acid with subsequent decomposition with nitric acid at pH = 1 to 1.5 to ensure maximum degree of rhenium conversion to the liquid phase of pulp. Some experimental lots of ammonium rhenate and ammonium molybdate were produced at a pilot plant. The following main techno-economic performance values have been achieved when processing grinding residues (balance-based tests were conducted with a lot of SP-2 alloy waste) to produce ammonium rhenate of high purity, as well as tantalum-niobium, nickel-cobalt and tungsten-molybdenum concentrates: rhenium recovery of 92.3% into a commercial product from grinding waste; production cost of 170-210 US Dollars per 1 kg of rhenium in commercial-grade ammonium perrhenate taking into account its recovery; tantalum and niobium recovery of 75- 77% into bulk concentrate; nickel and cobalt recovery of 88-89% into a mixed concentrate; tungsten and molybdenum recovery of 88% to 91% into concentrate. Introduction During the recent years the use of rhenium has been increasing at a fast pace worldwide [1]. The growing prices for this refractory metal are an essential factor encouraging collection and processing of rhenium-containing wastes. Double-component waste, such as molybdenum- rhenium or tungsten-rhenium alloys can be readily decomposed and the process of rhenium recovery does not cause, therefore, any difficulties. The main separation of metals takes place at the stage of waste digestion with acid, because molybdenum and especially tungsten remain in precipitate in the form of hydrated oxides and rhenium reports in the liquid phase, from which it can be easily extracted by solid ion-exchange or solvent extraction techniques. However, most of rhenium is contained in super-alloy waste [2]. Such waste has different contents of valuable components, such as tantalum, niobium, molybdenum, tungsten, cobalt, nickel, chromium and other metals. The basis of all such super-alloy waste is nickel. Refractory metals in the super- alloy composition are in the form of metallized target-oriented eutectics, and due to this reason hydrometallurgical decomposition of such alloys is a difficult technological task."

Jan 1, 2008

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Manuel Retamozo

El presente texto señala cómo el ejercicio físico adecuado y la dietética mejoran la producción y disminuyen el absentismo laboral en la empresa minera BHP Billiton Tintaya S.A a través de un política de prevención de salud. Entre los objetivos principales está determinar la frecuencia con que realizan ejercicio físico adecuado los trabajadores del área de mina, señalar si existieron cambios en las costumbres alimenticias de los trabajadores del área de mina después de la educación alimentaria, delimitar si existe asociación entre el aumento de la producción en el área de mina con la práctica del ejercicio físico adecuado y la dietética, así como entre la disminución del absentismo laboral en el área de mina con tales prácticas.

Jul 31, 2003

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

Iron Concentrate Synthesised from Waste Ferrous Sulfate Produced in Titanium White Preparation

Sep 13, 2010

By Valentín Pamo Caytano

La electrorefinación en un electrolito de CuSO4 - H2SO4 es usado universalmente para producir cobre de alta pureza a partir de los ánodos impuros. Aunque una parte de las impurezas se disuelve durante la electrorrefinación y se concentra en el electrolito, otros elementos son insolubles y se acumulan como lodos anódicos en las celdas de refinación. Las impurezas deben ser removidas del cobre para cumplir las especificaciones del mercado sobre la ductibilidad y conductividad y para recuperar los sub-productos valiosos como el oro y la plata. En ese sentido, el presente trabajo describe los equipos y procesos que permiten la recuperación del oro refinado en la planta de metales preciosos de la Refinaría de cobre de Ilo.

Sep 12, 2011