Search Documents

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

This paper is a collection of thoughts and frameworks. It addresses a simple question: æIf we are to believe the large number of people and institutions indicating that humans are destroying the Earth and that the end is nigh, why do we bother trying to be sustainable?Æ The paper lays out evidence for the existence of multiple hazards to global society. The existence of a hazard alone is insufficient to make an assessment of risk. Risk estimates are required to support decision-making. An approach to assessing risk is provided and some limited data are presented. A new ædefinitionÆ or statement of what sustainability (in a broad sense) might have become is then given. A decision framework for guiding decision- making about the risks is developed. This framework includes a definition of leadership with inherent implications for what determines whether a leadership position by title is actually leading. The paper concludes by offering a view of minerals industry sustainability and considerations around maturity in the current economic situation. It is hoped that by placing this collection of frameworks around sustainability, a supporting structure emerges that will facilitate action. It is proposed that action taken in this way will be more effective than reaction to regulation or even social license to operate imperatives because it is driven by a more holistic view of the challenges and the potential roles of individuals û all of whom are potential leaders at some scale of action.

Jan 1, 2009

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

This is what I term ... the graveyard end of any Conference. It's almost over. Those of you remaining are either all talked out or past the information overload stage. And some of the sensible? ones have left for more exciting field trips, or gone back to their work-site where they earn their daily crust, or headed off South to another Conference of interest to the Energy sector that is being held currently in Christchurch. But that's OK. I have a thick skin! And neither am I particularly Politically Correct! I am not a miner: I am not involved in the mining industry in a hands on way at all. I am not even an academic. I am not even too sure why I am here ... apart from the fact that I agreed to come! At various times in my life I have been a D istrict Councillor, Chairman of a Regional Council and even an MP. I am a supporter of responsible mining.  All of what I have to say is my own point of view rather than that of either the Coal Producers' Federation or the mining industry. That is not to say that we are often in agreement, but I thought I would clear that point right at the outset. And some of what I will talk about will not strictly be to the topic - it's hardly mind-bending riveting stuff. Well, is it? But obviously because you are still here you have some interest in the topic.

Jan 1, 1997

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

By L. P. Weber

During the years 1983-1987, a research programme, jointly performed by the steel producers ARBED, British Steel Corporation, Peine-Salzgitter, Unimetal, and co-sponsored by the European Community for Steel and Coal (ECSC), has been carried out on steel H-piles of different shapes. The initial aim of the testing programme has been the improvement of bearing capacity, both in sandy and clayey soils. At two test sites, standard H-beams are compared to H-piles with different types of laggings or to H-piles grouted both under low and high pressure. In this paper and in view of the open european market in 1992, the H-pile capacities and their corresponding allowable loads, determined from codes, recommendations and computation procedures in use in Belgium/Luxembourg (B/L), France (F), Federal Republic of Germany (G), and the United Kingdom (UK) as well as their evaluation from dynamic CAPWAP and Case methods are compared to the static capacities measured in-situ. In addition, procedures for estimating the load/movement behaviour of H-piles from CPT, pressuremeter, and CAPWAP are compared to the measured curves.

Jan 1, 1991

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

Mining is both a high risk and a long term business. This is dramatically illustrated by the fact that, on average, the explorer will expend over $30 million in a ten year period for each significant economic discovery. The time required to complete the exploration process is one of the most substantial commitments made by any mining company. For example the time lag between the implementation of an exploration programme and an economic discovery is variously estimated to take two to ten years. The ore definition phase following discovery currently takes between two and five years while subsequent mine development may take one to two years in easy situations and up to 8 in difficult environments. In most countries the critical path through the early stages is determined largely by technical considerations but in almost all countries the path through the later phases is dictated by the plethora of permits, licences and community involvement steps.

Jan 1, 1982

Grinding Mill Operation and Maintenance - Central to Asset Management Since 2005, RME has pursued a vision for a new grinding plant operational paradigm, made possible by RME's latest Mill Relining Systems. At some sites, new liners degrade SAG mill performance. The variables include mill volume loss, rotational speed limitations (ball strike) and liner designs developed for longer and longer life but without a backward glance at metallurgical consequences of whole plant performance. Freshly relined mills can initially deliver as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and relining speed become key profitability contributors and not simply 'must do' maintenance functions and costs. This paper includes a short history of RME's Mill Relining System development (Appendix A). These are the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The body of this paper outlines RME's vision of a 'liner profile vs. profitability' commercial model, underpinned by the rigour of PAS 55-1:2008 Asset Management Part 1: Specification for the optimised management of physical assets. The technical elements can be developed either intuitively (based on plant experience) or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum technical solution for the maximum commercial outcome. Much of this can be modelled off-line, in the virtual world, before asking senior management to commit to an expensive liner experiment. The potential benefits are compelling.

Sep 13, 2010

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014