Search Documents

As a result of early experiments in underground mine illumination, the Bureau of Hines recognized the need for additional experience with the underground lighting of coal mines having low seam thicknesses. There was already experience with tile illumination of coal mines having higher coal seams, and this contract with Ocean Energy Inc. (OEI) was undertaken to contribute to the "low coal" experience. For the purpose of this contract, a "low coal? mine is defined as one having less than 45 inches of overall headroom in the working places. As a practical limit, 26 inches was the minimum coal seam thickness to be encountered in this program. In one instance, the maximum coal seam thickness was eight to ten feet, however, this particular work was at the direction of the Technical Project Officer (TPO) by virtue of the unique type of lighting arrangement that was to be evaluated which would be useful for low coal. At the outset of the contract, three major tasks were established. The first two tasks involved the installation of permissible fluorescent lighting equipment at two low coal mines. The intention was to illuminate mining sections in each case consisting of one or more machines. The third task was to illuminate a variety or mining equipment including a longwall. For the purpose of this report, the fol-owing identifies the particular installations associated with each task.

Jan 1, 1976

By John C. MacCartney

In the Pennsylvania anthracite region, the principal source of U.S. anthracite, refuse disposal problems are common since cities and towns are located over the anthracite measures. The Bureau of Mines surveyed refuse banks in the area, determining that 863 banks containing aver 910 million cubic yards of material occupy a total area of about 19 square miles. The vast bulk of the refuse is located within 2 miles of the traffic centers of incorporated c unities which have a total population of 625,000. Twenty-seven banks are burning, causing considerable distress in a number of communities.

Jan 1, 1969

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By AIME AIME

FEATURES of the second fall meeting of the Petroleum Division for 1941, held at the Ambassador Hotel, Los Angeles, Oct. 29-30, were the forum on the Paloma Plan on Thursday after- noon, the large attendance from east of the Rockies, and the dinner on Wednesday evening sponsored by the Southern California Section and at which President Suman spoke on the strategic minerals and metals situation. The attendance was large and the technical fare uniformly good ; the presiding officers had the proceedings well in hand at all times and kept things humming. Some- times it was necessary to taper off the discussion because of pressure on time. All this was due to careful groundwork before the respective sessions. These presiding officers deserve citation: L. W. Huebel, Howard Pyle, E. K. Parks, Carlton Beal, E. G. Trostel. R. W. French, Jr., John Dodge, and H. N. Marsh. The Los Angeles local commit- tees and the Southern California Section deserve much credit for the arrangements, which were recognized by suitable resolutions at the end of the meeting.

Jan 1, 1941

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By Lloyd L. Farnham

This paper is one of a series describing the mineral resources of the Nation, including location, history, production, ownership, geologic setting, and mining methods for most of the known manganese deposits in New Mexico, With few exceptions these descriptions are the result of field examinations by the writer. Of 32 counties, the 12 which occupy the western half of the State contain all the known manganese deposits, These counties are Catron, Dona Ana, Grant, Hidalgo, Luna, Rio Arriba, Sandoval, Santa Fe, Sierra, Socorro, San Juan, and Taos. (See fig. 1.)

Jan 1, 1961

By Paul M. Tyler

"In preparing this paper the writer has perforce depended mainly upon published information, including the catalogs and pamphlets issued by importers and dealers such as the Diamond Drill Carbon Co. and J. K. Smit & Zonen. Special acknowledgment is made to various articles published by S. H. Ball. The writer of this paper, however, is alone responsible for statements herein contained and since he has often found it necessary to rationalize apparently conflicting opinions of recognized authorities on this little-known subject, he will welcome constructive criticism from the trade.Two types of diamond are extensively used for industrial purposes. One type, known as bort or bortz (boort, boart, bowr, etc.), consists of diamonds of the gem variety but unfit for cutting into gems. They may be colorless, yellow, brown, or gray. The other type, carbonado, known in the trade as ""carbon"" or ""black diamond,"" differs greatly from the white diamond, being opaque and apparently amorphous or noncrystalline. Actually, instead of forming a large single crystal as in a gem stone, carbon diamond comprises a mass of microscopic crystals that interlock to form a tough, homogeneous material with no planes of cleavage. It is found in various colors -- black, dark green, brown, and gray -- but usually it has .a dark lustrous black surface, with a resinoid or submetallic appearance, often resembling fine-grained steel. Upon exposure to the air the broken surface gradually darkens to an ash-gray color. Ballas is a special type of carbonado in which the crystals are definitely-oriented around a central nucleus. They are harder and tougher than ordinary carbonado but are much scarcer. The Cape ballas is reputed to be not quite so tough as Brazilian ballas but tougher than carbon or bort.The diamond crystals are isometric and take a variety of forms. The cleavage is octahedral and well marked. A crack is easily -started parallel to an octahedral face, and bort or gem diamonds are notoriously brittle, especially when subjected to sudden shock. Even carbonado, while it has a high resistance to slowly applied pressures, may be chipped or broken by a sharp blow.Exposed to radioactive rays, the diamond becomes phosphorescent; this property is often utilized to distinguish it from quartz, topaz, or glass. The unusually high refractive index likewise aids in its identification in the case of a more or less transparent stone. At the temperature of the electric arc, diamond is converted into graphite, another form of Carbon but one of the softest mineral substances. At a much lower temperature, as low as 1,5620 F., the diamond may be burned like ordinary carbon in an atmosphere of oxygen, and according to some authorities there is danger of burning a diamond if overheated even in air."

Mar 1, 1932

Our mission is help ensure our country has an adequate, dependable supply of minerals and mate al to meet its national security and economic needs at acceptable social, environmental, and economi[c] costs. We do this by promoting and encouraging private enterprise in the development of viable and stable mineral industries through the transfer of innovative extraction, processing, recycling, an environmental technologies; our use of cooperative partnerships with industry, academia, an government; our timely, authoritative worldwide mineral intelligence; our advocacy of public policies based on good science and sound economics.

Jan 1, 1994

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Glenn E. Johnson

The Bureau of Mines investigated the production of hydrogen cyanide by reacting powdered coal (minus 300 mesh) with ammonia at 1,250° C in a bench-scale study. Both metallic and ceramic reactors were used. Yields up to 0.7 cu ft of hydrogen cyanide per cubic foot of ammonia consumed r- obtained. The resulting ammonia conversion of about 75 volume-percent approximates conversion obtained commercially in processes utilizing natural gas and platinum catalysts. The coals that had higher volatile-matter contents gave the best yields of hydrogen cyanide. Allowing the coal to adsorb ammonia before reaction resulted in increased yields of hydrogen cyanide. Cost studies for a plant with a 40-million-pound-per-year capacity indi-cate that hydrogen cyanide can be profitably coproduced with carbon black, from coal and ammonia, at the current market price of hydrogen cyanide (11.5 cents/lb). These figures are based on heating the reactor electrically. If a cheaper heating method were devised the economics of the process would be more favorable.

Jan 1, 1967

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

Background ArcelorMittal?s (formerly QCM?s) Port Cartier iron ore pelletization operations 2 side-by-side induration furnaces each producing 578 t/h of cured pellets Firing No. 6 fuel oil and coke breeze (in bed) Very large heat losses to be addressed primarily by gas recirculation

May 1, 2011

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936