Search Documents

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By E. LaRocque

"Denison Mines Limited has been processing uranium ore in the Elliot Lake area since May of 1957. The ore body is located i11 the Huronion sediments on the north limb of the Quirke Lake syncline. Minerals of metallurgical significance are brannerite, uraninite and monazite. Gangue minerals include quartz, chlorite, sericite, pyrite, pyrrhotite and rutile. Silica content of the ore is greater than 75 % and pyrite-pyrrhotite content around 7 %. Specific gravity of the ore is 2.75.The Denison flowsheet is based on sulphuric acid leaching to extract the uranium values from the ore followed by liquid-solid separation to wash the uranium-bearing solution from the barren ore. The resultant pregnant solution is concentrated and purified by ion exchange followed by two-stage precipitation with ammonia to produce an ammonium yellow-cake.Elliot Lake ores require high acid concentrations and high temperatures to extract the uranium from brannerite and monazite. Uraninite will leach at low acid concentrations as long as oxiclizing conditions exist. The whole ore must be treated so that these conditions do exist.This paper provides a description of the leaching process equipment as originally installed and major changes in that equipment to date. Process control refinements to economically improve extraction are also discussed."

Jan 1, 1979

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By R. Venugopal, Saxena. V. K., U. Sankrityayan

"There is a dire need of a technology which can break the mineral interfaces to enhance liberation with minimum energy consumption in mineral beneficiation processes. Understanding of mineral crystal system and interfaces is essential to develop such methodology. So, this study is carried out to find out the role of mineral crystallography in milling and liberation. Data related of mineral crystallography, Vickers Hardness Number, Bond Work Index and beneficiation processes were collected from literature and detailed statistical analysis has been carried out to establish a correlation among these parameters. It was found that atomic weight and cell parameters shown statistically significant relationship with Vickers Hardness Number of minerals, which controls the milling characteristics of ores. Liberation characteristics of five different kinds of ores were analyzed considering the types of interfaces between valuable and gangue minerals. It was found that phase interfaces play vita role in liberation and coarser liberation can be achieved in the minerals of incoherent crystal systems like manganese and zinc ores. Study of this subject can help us to understand the effect of stress wave propagation in solids and its effect on crystal interfaces. It can also help us to design a technology of future to break the mineral interfaces.INTRODUCTIONCommunition is energy intensive mineral processing operation and consumes up to 2% of the total electric power generated in the world. Energy consumption due to comminution is increasing every year as there is growing needs to exploit lower grade ore bodies and process rejects (Blazy et al., 1994; DOE, 2005). Low grade ores require crushing and grinding to liberate the valuable minerals which are further separated from gangues by various beneficiation methods like gravity separation, floatation, leaching etc. Currently, comminution methods are selected based on the reduction ratio and energy consumption but effect of grinding methods on subsequent processing methods specially on liberation also need to be studied to optimize the entire beneficiation process. Most of the attempts made in past to minimize the energy consumption in milling to enhance the mineral liberation were focused on compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Kilpelm and Austin, 1982; Norgate and Weller et al, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang el al., 2011; Singh et al., 2012). But the role of mineral crystallography on milling and liberation behavior of minerals not fully explored yet."

Jan 1, 2013

By G. Laing

On scheduled commissioning and effective operation of a solvent extraction circuit relies on getting the design of both the core contact equipment and the peripheral plant right. Experience has shown that poor performance of new plants is frequently a result of ?utility? systems that do not match the requirements of the circuit, rather than the mass transfer equipment itself. Both the operator/owner and designer need to understand the ?complete requirements? for the circuit to get the balance of the design right. This paper reviews generic issues, frequently overlooked or altered during cost-cutting exercises, which have a significant impact on plant performance.

Jan 1, 2002

By Dae S. Young

The paper point out a new procedure to calculate the volumetric distribution of rock fragments. The method combines the practicality of digital image processing of the rock surface with the theoretical volume calculations based on principles and laws of fractal geometry. The final volumetric distribution curve is compared with the results from traditional sieving indicating close agreement.

Jul 17, 2000

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Daniel H. Israel

Indian tribes own a substantial portion of the West's minerals. More importantly, Indian reservations contain coal, oil and gas, uranium, and oil shale reserves in unusually large and unencumbered blocks. Many tribes are now prepared to intensify development of their large reserves knowing that they can offer energy partners the unique opportunity to develop major energy facilities free of overlapping local, state, and federal permitting authorities. The tribes, therefore, can offer mineral developers both substantial reserves and an unusual degree of freedom from a multiplicity of government regulation. In the past, Indians and energy companies enjoyed only partial success as business partners. Indian tribes lacked the resources and know-how to act as equal partners with large oil and gas and mining operators. The tribes relied on the Bureau of Indian Affairs (BIA) to initiate and execute reservation energy projects, and as a result the tribes never developed adequate tribal structures and the expertise to responsibly manage their energy resources. At the same time industry made little effort to understand and learn the laws, customs, and institutions existing on Indian reservations. To the contrary, industry found it easier to bypass the tribes and deal with BIA officials. But the situation has changed. In 1975 the tribes organized an effective coalition, the Council of Energy Resources Tribes (CERT), which recently acquired substantial federal assistance to bring the tribes a level of technical and business expertise that begins to equal that of industry. Because the tribes have changed the rules of the game, industry must now change and learn to work directly with tribal governments. A working knowledge of Indian law, practices, customs, and policies must be acquired by energy companies before beginning negotiations with tribal governments for development of reservation energy resources.

Jan 6, 1980

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984