Search Documents

By Floyd C. Kelly

There is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensataion of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is little gained by using specially purified gas, because it becomes contaminated after reaching the furnace. Low-carbon Steel If a sheet of low-carbon steel is annealed in such a furnace at 750" C. and allowed to cool with the furnace, an adequate flow of purified hydrogen being maintained all of the time, the steel will come out with a very thin coating of blue oxide. If a similar sheet is annealed at the same temperature and quickly pushed into the cooling chamber, it will come out nearly bright, or perhaps with only the edges slightly discolored. It is difficult to get a piece of steel through a furnace of this type with an absolutely bright surface. This is due to the fact that there are always traces of oxygen or water vapor in the furnace. When the steel is allowed to cool with the furnace, it reaches a critical temperature where the affinity of iron for oxygen is greater than that of hydrogen for oxygen, and the steel comes out discolored. If the steel is pushed from the hot zone

Jan 1, 1931

Lieutenant Gorman was born in Ottawa, Canada, in 1888, and after preliminary education at Ottawa University and the Ottawa Collegiate Institute, he graduated from McGill University in 1913, as a mining engineer. After graduation, Mr. Gorman spent several months in a tour of Europe. The year 1909 was occupied at one of the Canadian graphite mines, and the summer of 1911 he spent with the Granby Mining, Smelting & Power Co., Ltd. At the time of his admission to the Institute, in 1914, he was sampler with the Dome mines at South Porcupine, Ontario. His next engagement was at the Creighton mine, Ontario, but in 1916 he joined the Canadian Expeditionary Force and went to England. A letter written by Major Ritchie, commanding the Second Tunnelling Company, to Lieut. Gorman's mother, contains the following words. Tommy was lulled at our headquarters by a nine-inch shell which struck the officers' quarters. The Hun had been shelling a small village close to the camp with a long-range gun and a shot fell into our camp. Tom was killed instantly by the concussion. He mas buried this morning with Military Honours in the military cemetery close to our camp. Tommy was an efficient officer and a good soldier and his loss is very keenly felt by the officers and men of this unit. Lieutenant William Hague William Hague, First Lieutenant Co. F, 116th Regiment of Engineers, and a member of the Institute since 1906, died of pneumonia in France, on Jan. 1, 1918. Lieutenant Hague was born in Orange, N. J., Mar. 31, 1882, the son of the late James D. Hague, a distinguished mining engineer and a life member of the Institute, and Mary Ward (Foote) Hague, of Guilford, Conn. He attended Milton Academy, Milton, Mass., and was graduated from Harvard in the class of 1904. He was a nephew of the late Arnold Hague, of the United States Geological Survey. Seven years ago he married Elizabeth Stone, of Milton, who with their son, James D. Hague, six years old, survives him. Lieutenant Hague's mining career began immediately after his graduation from Harvard, when he went to Bisbee, Ariz., to be a surveyor's helper in the mines of the Copper Queen Consolidated Mining Co. In 1905, he became an instrument man, being engaged on the construction work of the Copper Queen smelting plant at Douglas, Ariz. In the latter part of the same year he was transferred to the geological depart-

Jan 1, 1920

By P. A. Beck

ACCORDING to a recent hypothesis of Sully,' xY. binary CT phases are characterized by 1.7 bonding 3d electrons per atom, which completely fill the first Brillouin zone. This hypothesis appears to imply that there are no empty 3d orbitals in the u phase, and that, correspondingly, this phase must be dia-magnetic, or at most weakly paramagnetic. On the other hand, Bowen and Hoar' reported that a u phase extracted electrolytically from an alloy steel became ferromagnetic when cooled to about —113°C. In view of the fundamental interest of the problem from the point of view of the electron structure of the u phase, it seemed worthwhile to study the magnetic properties of massive u phase specimens of various known compositions. Sigma specimens of the following compositions were tested: 1—40 atomic pct Fe, 40 atomic pct Cr, and 20 atomic pct Mo 2—35 atomic pct Fe, 35 atomic pct Cr, and 30 atomic pct Mo 3—48.7 atomic pct Fe, 50.2 atomic pct Cr, and 1.1 atomic pct W 4—40.7 atomic pct Co and 59.3 atomic pct Cr All specimens were found to be strongly paramagnetic at room temperature, particularly alloy No. 1. At liquid nitrogen temperature, alloy No. 1 be- came ferromagnetic; the other u alloys remained paramagnetic. Even though apparently not all u alloys become ferromagnetic at liquid nitrogen temperature, in view of their strong paramagnetism it is probable that the electron structure proposed by Sully is not correct. Similar qualitative studies were made with the p, P, and 8 phases." A p phase specimen of 57.2 atomic pct Co and 42.8 atomic pct Mo; a P specimen of 19.9 atomic pct Cr, 37.8 atomic pct Ni, and 42.3 atomic pct Mo; and a 8 specimen of 50.4 atomic pct Ni and 49.6 atomic pct Mo were tested at room temperature, and all were found to be paramagnetic, although considerably weaker than the u phase specimens described above. A test at liquid nitrogen temperature gave similar results for all specimens; none became ferromagnetic. Thanks are due to D. K. Das for preparing several of the alloys and to Pol Duwez of California Institute of Technology for kindly loaning four specimens of cr alloys. References 1 A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, p. 173. - K. W. J. Bowen and T. P. Hoar: Low Temperature Ferromagnetism of Sigma Phase in an Alloy Steel. Research (1950) 3, p. 484. 3 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951).

Jan 1, 1953

By Marlene Olivares Cruz

The particles that make up the deep-sea sediments have two main sources: 1) those that are created in situ from dissolved components and 2) those that are washed into the ocean in solid phases from the continents, atmosphere, space and interior of the Earth. Many particles as they sink through the water column reaches the seabed and are known as pelagic sediments with terrigenous, biogenic, authigenic, and cosmogenic components. Among the minerals found in the terrigenous fraction of pelagic sediments are quartz, clay minerals, feldspar, micas, ferromagnesians, and the biogenic fraction with remains of siliceous organisms, such as, radiolarian and diatoms. The chemical nature of marine sediments is controlled by the contribution of particulate matter derived from various sources with varying compositions for the fixing of elements during deposition and the compositional changes carried out within the sediments during diagenesis. In the last decade there have been several studies on the mineralogical composition of seabed sediments, suspended particulate materials and cores, together with paleontological and geochemical data are used for paleoclimatic and paleoenvironmental reconstructions, analyze changes in sea level, stratigraphic correlations and identify past and

Sep 14, 2011

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By Alfred R. Powell

FOR the purposes of this discussion, the direct gasification of coal means the of hydrogen and carbon monoxide by the well-known water-gas reaction. Chemicals or other synthetic products may be made from these constituents of the gas and under such circumstances the gas is called synthesis gas. Or, if the same gas is used as a fuel, it is called blue gas or water gas. This type of gas has usually been made from coke, especially in this country, and has been used both for fuel purposes and for manufacture of chemicals. Recently, natural gas has gained the ascendancy as a source of synthesis gas for manufacture of chemicals because of its relative cheapness. As natural gas becomes less readily available and more expensive, coal will take its place as a raw material for the preparation of synthesis gas. This substitution will probably take the form of direct gasification of the coal rather than the present two-step procedure of carbonization of the coal followed by gasification of the coke. The chief reason for this probability is the intensive research now being carried on by several organizations to develop successful and economical processes for the direct gasification of coal, which is a considerably cheaper fuel than coke. In the following pages an attempt has been made to predict the chemicals that will result from this future production of synthesis gas by the direct gasification of coal. CHEMICAL REACTIONS OF SYNTHESIS GAS Given the proper conditions, there are many chemical reactions leading to production of useful products that can be carried out with this mixture of hydrogen and carbon monoxide. These many reactions may be grouped into three classes: (1) interaction of hydrogen and carbon monoxide, possibly with addition of other reactants; (2) reaction of hydrogen with various substances; (3) reaction of carbon monoxide with various substances. Thus sometimes hydrogen and carbon monoxide are utilized together in the same chemical reaction while in other instances only the hydrogen or only the carbon monoxide is required as a reactant. Fortunately, practical methods are available for securing either hydrogen or carbon monoxide from synthesis gas, some of which are also applicable for changing the ratio of these two constituents in the gas when that is desirable.

Jan 1, 1953

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By John D. Gill

THIS paper assumes the incontrovertible nature of the statement that the validity of competition in the nonnatural resource industries is established firmly on the rate and extent of the economic development of the United States. It then demonstrates the nonexistence of any condition within the petroleum industry that would invalidate the principle of competition as applied to it. It points to the benefits that competition has effected in the oil industry and the reasons why the practice of the competitive principle should continue to keep the industry virile and progressive in meeting the requirements of future generations for the kind of products natural to it. Finally, it pleads for a clearer view of the affairs of the oil industry by seeing them against a background of the whole economy. INTRODUCTION Even a few years ago there would have been only an academic reason for presenting before this Institute a paper on the validity of competition in the oil industry or any other natural resource industry; today there is no more practical subject for this body to consider. In social importance it transcends attempted solutions of perplexing technical problems; and even the numerous legal and economic problems that grow out of administration of state regulatory measures appear to be of secondary importance because they would cease to exist if competition were abolished. The aspiration of certain elements of the Federal Government to acquire control of the oil industry has long been suspected The vital need for petroleum in the national defense ... confirms my belief in the urgent need of Federal legislation to safeguard our petroleum supply through prevention of waste and by establishment and maintenance of sound economic conditions in the oil industry... . But also it may be dismissed with this mere mention of it because it predicates government control and the abandonment or broad reduction of competition on a war emergency. Clearly, the fight for a nation's life may justify a government's control over men and resources that would be abhorrent and economically enervating under conditions of national security. More pertinent to the present matter, because it appears expressive neither of a personal ambition nor of an emergency condition but rather of the long-range view of a certain school of conservationists, is the pronouncement of no less an authority than the Attorney General of the United States, who has been repeatedly quoted by the press as saying that the American Petroleum Industry constituted a case "where the principle of conservation of an exhaustible and irreplaceable resource should replace the principle of competitive exploitation." The significance of this statement in the light of the commonly accepted meanings of the " principle of conservation" and of the "principle of competitive ex-

Jan 1, 1941

By Omar A. Muhtadi

8.1 INTRODUCTION Several methods currently exist by which gold may be recovered from a pregnant leach liquor. Two of these methods are discussed in this chapter, the Merrill-Crowe (zinc cementation) process and the carbon adsorption process. These two methods represent the most frequently used techniques for gold extraction and are, -in fact, used almost exclusively in U.S. heap leaching operations. Because of the efficiency and ease of use of these two methods, it is extremely likely they will continue to be quite prevalent within the gold mining industry in years to come. The remainder of this chapter includes information on the history of the two processes, descriptions of the actual processes, criteria to consider in selecting a recovery process, and commercial design and construction considerations for both of the gold recovery methods. As with other chapters in this book, some fairly technical information is presented for the benefit of those readers needing a greater level of detail. However, the overall intent of the chapter is to provide an overview of the processes likely to be used in gold extraction, thus giving the reader a firm basis for more technical research into the topic, should this be needed. 8.1.1 History of Zinc Cementation During the late 18901s, zinc cementation was introduced for the precipitation of gold and silver from cyanide solutions. This occurred at about the same time as the introduction of the cyanidation process, the history of which is recapped in Chapter 1. The initial cementation process involved introduction of a gold-bearing cyanide solution onto a bed of zinc shavings. It proved to be quite inefficient because the reaction rate was very slow. The zinc quickly became "passive", inhibiting further gold deposition. Shortly after this first introduction, zinc precipitation was improved by adding a lead salt (usually lead nitrate) to the zinc. This allowed a zinc-lead couple to form on the surface of the shavings, eliminating passivation of zinc surfaces and thereby allowing continued deposition of gold. Further improvements were shortly forthcoming. The first of these involved the use of zinc dust rather than zinc shavings. This provided a much

Jan 1, 1988

The first Mine Rescue Performance Evaluation for mine rescue teams was held just prior to the 1992 RMCMI convention meeting schedule on June 27 and 28. Six teams took part in this year's evaluation; Decker Coal, Decker, Montana; BHP Minerals' White Team and BHP Minerals' Purple Team, both of Aztec, New Mexico; Kerr McGee Coal Corporation, Jacob's Ranch Mine, Gillette, Wyoming; The Coteau Properties Company, Freedom Mine, Beulah, North Dakota and The Falkirk Mining Company, Falkirk Mine, Underwood, North Dakota. This was the first mine rescue evaluation program developed to measure a unit's proficiency in their skills rather than emphasis on a ranking order of teams. The objectives for the evaluation were to promote learning and to evaluate the current level of experience of the attending rescue units. The priority goal for this evaluation was to recognize current rescue skills, knowledge and abilities of each team participating. In doing this, each team is provided with individual evaluations and a path for improvement as needed. [ ] Realistic industrial related scenarios, closely simulating the stress of actual rescue incidents, was provided by members of the Hermosa Cliffs Colorado Fire Department under the direction of Dan Noonan, Fire Chief. On Saturday, June 27, five rescue scenarios were presented for each team to complete and on Sunday three of a more difficult nature were encountered by each team. On the final day of the RMCMI convention two of the teams performed rescue demonstra¬tions. Onlookers were afforded the opportunity to view the teams in action as they simulated actual rescue operations. The value and importance of mine rescue teams such as those participating in this year's Rescue Team Performance Evaluation are very evident as in many cases they are the only rescue personnel and medical staff on the work site in case of an emergency. Most of these persons are volunteers who spend many hours studying, practicing and perfecting their expertise in the lifesaving techniques needed in the event of a mine emergency. At the same time, they are very qualified coal miners who perform their respective duties at their mine locations, Their dedication to gaining the most knowledge they can get to handle these life and death situations is evident in their participation in evaluations such as this one. [ ] If a highly educational, informative, sharing of knowledge and expertise, while at the same time providing a very enjoyable experience, deems this evaluation a success ... the Rescue Team Performance Evaluation held during the RMCMI Convention at Tamarron this year was certainly a SUCCESS!! It is hoped that you can all enjoy this same experience with us next year! Linda G. Ash The Falkirk Mining Company [ ]

Jan 1, 1992

By José Gutiérrez, Fernando Saez

El presente trabajo propone una metodología para la categorización de recursos minerales aplicando el balanced scorecard, el cual sigue las mejores prácticas de los códigos internacionales (JORC, NI 43-101, etc). El caso de estudio refiere a la veta Soledad localizada en Mina Caylloma propiedad de Minera Bateas.

May 1, 2008

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By S. Weinig, E. S. Machlin

THE mechanism of the martensitic transformation has been the subject of a remarkable number of papers in recent years.' Because the task of evaluating all the available theories is a formidable one, the authors will confine themselves merely to the presentation of results of an experimental investigation of the habit orientation, lattice relations, magnitude and direction of average transformation shear strain, and orientation of subband markings for a single variant of the possible habit systems in an 11 pct Mo-Ti alloy. It is hoped that these data will assist in the establishment of a rigorous theory for the mechanism of the martensitic transformation. Experimental Procedure Specimen Preparation: A sample, approximately 1/2 x 1/4 x 1/4 in., was cut from a double arc-melted ingot composed of commercial-process A titanium and high purity molybdenum (nominally, 11 pct Mo). It was capsuled in evacuated Vycor at 10.-3 mm Hg subsequent to a double argon wash and homogenized for 48 hr at 1100°C. After a direct quench into H2O at room temperature, a large-grained specimen resulted, which, by X-ray diffraction and metallographic means, was subsequently shown to be in the body-centered-cubic phase, ß. Two adjacent, approximately perpendicular faces were polished and the ends of the specimen were ground parallel in a V-block. Fiducial lines were inscribed at 45" to the common edge of the polished surfaces in order that they would be perpendicular to the habit traces of the subsequently formed a plates.2 The specimen was then compressed between the ground ends in a Buehler press to stress induce the transformation ß to a'. Experimental Measurements: The habit-plane orientation, the orientation of subband markings, the orientation relation between the parent ß and the product a', and the transformation strain for the same plate were determined. To further establish the nature of the subbands, one surface was repol-ished and etched. The bands in the a' were still visible and were found to be optically anisotropic under polarized light. Back-reflection Laue patterns were obtained from the ß matrix and from a region comprising both a' plates and adjacent ß matrix (a Cu target was used). By superposition of the two X-ray diffraction patterns, it was possible to obtain a tentative orientation relationship between the two phases. This result was confirmed by a pattern taken after the specimen was rotated to make the basal-plane pole of the hexagonal a' phase strike the film. This necessitated cutting the specimen to expose the a' plate in the new position relative to the X-ray beam. Analysis of Experimental Measurements On the basis of the aforementioned X-ray patterns, the orientation between parent and product

Jan 1, 1955

By John Blandy

EVERY new mining district has had its own peculiar experiences in inventing and experimenting upon new methods for the various operations of mining, and more particularly in the processes of crushing and dressing ores. As a matter of course, during this period many old things have been reinvented, patented, and cast aside, there to remain until at a future day other geniuses shall bring them forth again as new. In this respect the Copper Region of Michigan has not been behind other mining centres, and probably in no other part of the country has more money been expended in devising new machines and improvements upon old ones for the crushing of the rock. The appliances for washing the sand have not been so varied, simply for the reason that, having but one mineral, or rather metal, of high specific gravity to separate from rock material which varies but little in its character in any one mine, it requires much less care than is necessary in most mining centres of the world. At the beginning of operations in that district most of the work was in the control of Cornish miners, who introduced the simplest of Cornish mills, namely, wooden stem pestles, with wooden shafts and cams. These were well suited to the small mines, and particularly to the limited means of transporting more expensive machinery. As these facilities improved, they were enabled to change to iron, and to vary their patterns of rods, shafts, cams, and mortars. The most approved pattern, finally obtained, is the square or round stem, with collar adjustable by means of keys. In its present form it is a bar of cold rolled shafting, an eye in the top, an adjustable collar with key-plate and keys, the head and a shoe of chilled iron. The stem is fitted into the head by a slight taper. The battery has heretofore been of wood, lined with chilled cast plates, and bed-plate of the same, but within the past year the California pattern has been introduced. The screens are of sheet-steel, drilled with 16 holes to the inch. During this period of trial and gradual improvement in the pestle stamps, in the years 1855-6, the Ball steam-stamps were intro¬duced, and after years of labor and expense, have been made the most efficient and powerful machines ever yet used for the purpose. It is ostensibly the Nasmyth steam-hammer, and yet the

Jan 1, 1874

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

By Barnabus Bryan

THE normal statistics of supply and demand of petroleum and its products have little more than local influence on the market movements of oil securities. The two major reasons for this condition might be called the technique of production and the technique of refining. The speed of improvement in each and the complete lack of control of their, inter-relation have resulted in overproduction of both crude oil and gasoline in the face of immense in-crease in demand. The trouble with oil securities has been that of the mushroom radio companies, where too frequent changes have killed the possibility of profits. It is a case of too much efficiency. During the past ten years there has been continual talk of wasting reserves of crude oil. This has been based on "present methods of production." Yet the methods of ten years ago in the oil industry are as antiquated today as the kerosene lamp.. The fear of famine has transformed the industry. The refiner, through the cracking process, has doubled the gaso-line output from a barrel of crude oil, thus doubling reserves and changing a current undersupply into oversupply. When the automobile driver desires he can again double reserves and transform want into abundance by demanding an automobile which will deliver twice as many miles per gallon of gasoline. Entirely apart from refining and in complete dis-regard for its needs, the oil producer has forged ahead at a pace too rapid for his own good. The science of geology has developed with experience and' lavish expenditure into a constant danger to profits in the production of oil. Two and one-half per ;cent of the producing wells in the United States are yielding one-half of the oil, while their flush production is used as an excuse to force down the price of crude oil until 200,000 wells must be abandoned or produce at a loss. The fabulous yield of the new high-pres-sure fields enables the fortunate owners to make a profit regardless of the price of oil. Such a condi-tion is unhealthy from the standpoint of oil itself and as a national policy. It is manifestly absurd to suppose that such a condition can endure for a gen-eration. There will come a day when the sequence of discovery will be temporarily broken, and at that time the consumer will be forced to pay heavy interest on the foolhardy policy of today.

Jan 6, 1927