Search Documents

By Newell G. Alford

The data in this paper were collected to show both the volume and speed with which bituminous mines have indefinitely suspended operation while economic advantage in the industry has so gravely declined. The study was limited to the bituminous coal-mining states east of the Mississippi River, wherein conditions affecting production and demand are more common respectively to all of the mining districts included and represent about 95 per cent of the nation's coal mining. Data for the compilation of these statistics and for the construction of these graphs have been obtained in all cases from state mine department reports, except from those of Ohio and Virginia. In Virginia essential individual mine data were secured from an authentic source, but no individual Ohio mine information is obtainable, because all Ohio fact-gathering agencies are prohibited by law from revealing such data. In other states the facts were tabulated and later checked with the cooperation of Chief Mine Inspectors. In all, excluding Ohio, over 17,000 individual annual mine returns were examined. Special information was secured from each state mine department about suspensions in 1932. Accurate information was not available from all states about nine abandonment due to exhaustion of coal reserves, and while these were completed for several states, it has not been shown because it was not perfected for all states. However, the total observed sample mas comprehensive enough to show that exhaustion accounts for a very limited part of the suspended production. Wherever mention is made of '(suspended productionJ' the largest annual output of the mine in the five years prior to suspension has been taken as the measure of its probable production had it continued to operate. A mine is not regarded in this category, as having suspended, when it merely ceases to produce. The word "suspension" is used only where there is a complete abandonment of activity for an indefinite period, as evidenced by the fact that both ventilation and pumping are discontinued.

Jan 1, 1934

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969

By J. T. Crawford

THE purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities, being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-gravity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 1 1/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from ½ to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder.

Jan 1, 1938

By Z. Kowalski

In the defunct Gorka quarry, there are situated both a waste disposal site of an area of 6.7 ha and containing approximately 1 million ton of high aluminium wastes and a pond of an area of roughly 3 ha, up to 15 m deep, with about 400000 m3 of polluted water. The reservoir is fed with the filtrates arriving from the disposal site mentioned, at a rate ~130 m3/day. An alarming phenomenon is the subsidence of the pond bottom and the infiltration of solutions into the Triassic and Jurassic water resources, assessed at ~40 m3/ day. The basic problem related to the effluents in the Gorka pond is their high alkalinity (pH 12-13.4) and variable pollutants whose level increases appreciably with the pond?s depth. The solution offered provides pumping out and treatment of about 500000m3 of effluents retained in the Gorka reservoir in an about yearly time. Effluents would be treated in a reverse osmosis plant, according to a process so far verified on a quarter-commercial scale. The treatment process by-product would be discharged into the Ropa stream. The brine solution (containing about 25% NaCl), whose amount may reach up to100000m3, might be supplied to the Debiensko Mine which produces technological salt from salt-bearing mine waters. Similarly, there would be provided an intake of underflows of infiltrates (by means of deep wells, and possibly girdling ditches) arriving from the high aluminum site, and such effluents would be subject to ongoing dilution in water courses. It would be possible to test the system of underflows reaching the Gorka reservoir by means of geochemical identification, previously performed. The next stage following the pumping, would be the utilization of approx. 50 000m3 of bottom slurry. Highly alkaline slurries would be utilized in the production of self-solidifying mixtures. Slurries would be pumped out and temporarily dumped on drying beds, located nearby the Gorka reservoir, and later on used successively for making self-solidifying mixtures in a plant similar to a concrete making seat. Those mixtures would be applied for sealing the bottom of the Gorka reservoir and the necessary part of the edges of the defunct quarry. An alternative solution is the utilization of slurries in the facilities of the Trzebionka Mining Works and the application of self-solidifying mixtures, made in the Trzebionka Works, for sealing the reservoir bottom.

Jan 1, 2006

By F. L. Wolf

THERE is a tendency on the part of practical foundrymen to accept with reluctance the results of tests on sands, binders, and. such materials made in the chemical laboratory alone. They feel that such tests frequently emphasize and measure properties that are of minor importance and fail to take account of characteristics that are important in determining the value of the material in actual practice. Experience seems to indicate that the most thorough and conclusive, test for any new foundry material is an actual run in the foundry alongside of a standard material of known value. Such a test, however, involves certain difficulties and necessitates certain precautions. It is not always easy to obtain a fair trial for a new material. We all have certain prejudices, which unconsciously affect our judgment to a marked degree. A practical test frequently involves so many workmen, each of whom reacts in a different manner to the test, that; the personal equation becomes very, complex and the true results of the test are obscured. There are times, too, when a thorough experimental trial of a material would interfere too much with the rush of work in a department or would hazard the quality, of the product to such an extent as to make it inadvisable. Under such conditions a laboratory test is advisable before the material is sent into the foundry. These tests should be made as practical as possible and so closely related to foundry practice as to give a true index to the value of a, product for the purpose desired. Core sands and molding sands are as numerous "as the sands of the sea" and vary as much in quality. Old sources of supply are continually failing and new ones must be opened, so that we must continually search for new and better grades of sand. During the past year, the Ohio Brass Co. has developed tests for sands&apos;, cores, and binders which bear a close relation to the particular use to which these materials are put in

Jan 9, 1920

By Erol Yilmaz

This poster presents results obtained from an experimental test set-up called CUAPS (curing under applied pressure system) allowing to assess the performance and quality of cemented paste backfill (CPB) materials. CUAPS can be used for carrying out a series of tests: one-dimensional consolidation, saturated hydraulic conductivity, pore-water pressure dissipation, and curing under uniaxial stress. The poster presents CUAPS testing preliminary results including uniaxial compression tests (UCS) and mercury intrusion porosimetry (MIP). It was demonstrated that CUAPS-consolidated CPB materials cured under time-dependent stresses provide higher UCS values than standard mould (undrained and unconsolidated) CPB samples. This may be explained by the release of excess pore water within backfill that gives rise to a significant reduction in the total porosity of fresh CPB materials prior to hardening and thus, to higher mechanical strength (UCS) gain. The results obtained from MIP highlighted a good correlation between CUAPSconsolidated and mould-unconsolidated CPB samples. MIP results were also related to UCS values in order to predict the final CPB mechanical strength.

Nov 1, 2008

By Wilford Stork

CERTAIN influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,1 such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is really burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book3 The work of J. E. Johnson, Jr., has revolutionized

Jan 6, 1919

A low grade, refractory ore gold mine with high striping ratio such as at Macraes is always challenged in ways to improve margins. Common practice approaches used at OceanaGold Ltd Macraes are to maximise grade delivery, optimise recovery and reduce unit costs, as well as take any opportunities to incorporate new technologies and implement enhanced commercial strategies. &nbsp; The Business Improvement (BI) programme was implemented across the Macraes operations in late 2003 and is being rolled-out to all other parts of the business. The core focus of BI at OGL is to: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; increase revenue, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; reduce cost, and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; improve processes. &nbsp; A dedicated BI team comprising of a manager, team leaders and business analysts were engaged to identify and manage a series of opportunities to reduce operating expenses, optimise capital outlays and generate extra revenue. The Business Improvement Programme, though in its formative phase, has begun a cultural change within the organisation. Many people are starting to challenge the way they do things and are looking for ways to continually improve business performance. &nbsp; The BI team encompasses individuals from different departments who can offer the diverse skill set necessary to produce intended results. The current team is made up of a BI manager, BI Team Leaders in Mining and Processing and analysts from Mining, Processing, Commercial and Plant Maintenance workgroups. A team member has recently been formally trained as a Six Sigma Black Belt. ] The BIÆs team role is to assist in the establishment of project management processes for each improvement idea. In addition the team will assist in tracking implementation, identifying and unblocking restrictions and limitations as well as setting up metrics to quantify the level of benefit returned and sustained. &nbsp; From a more strategic point of view, the BI team is advancing the Business Improvement capability of the company by developing long term Communication and Training strategies. These strategies will set the direction of BI initiatives in the years to come to: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; educate the OGL workforce in basic BI techniques, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; assist the OGL workforce in applying basic BI techniques, +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; communication the direction of BI in OGL, and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; close the information feedback loop to facilitate transparent communication between the OGL workforce and the BI team.

Jan 1, 2004

IN the western mines, the boss, engineer, geologist, or nipper in making rounds have a password which usually guarantees safe entrance to a working place from below the working miner. Most men won&apos;t climb a raise or enter a stope from below where a miner is working until they have shouted "nothin&apos; down" and heard those words shouted back by the miners above. "Nothin&apos; down" is a safety pledge as necessary and as binding as the truce flag to the soldier. It implies mutual confidence that work will be suspended until the person below has come abreast of the workers; and also confidence that the miner who replies "nothin&apos; down" is reasonably sure the place is safe to enter. Like truce flags which are not infallible, so is this password subject to human errors or unexpected falls of rock, tools, or timber. Everyone knows these unavoidable hazards, but what is important to the exposed man is that in that precise moment of time when he has heard the reassurance of "nothin&apos; down," he knows that safety is uppermost in the minds of the men above him. With such assurance we would go anywhere and so would most mining men. If that period of safety consciousness, procured by the utterance of two words, could be multiplied to equal the hours in the working day, there would not be any accidents but those by "the act of God." It is the aim of every safety program to make safety as natural as breathing. That is the reason for the posters, the conferences, instruction periods, safety engineers, and the inspections. But none of these are as effective as one accident, which keeps men on their toes for weeks to come. This is not the price we want to pay for safety consciousness. This Annual Review number of Mining Engineering is full of talk about production. Production for defense, production for profit. In this tremendous surge of industrial might . to make this nation and our very families safe S from the predatory forces abroad in the world today; let us not lose sight of the fact that the . safety of our manpower is more precious than any commodity. Production without safety is detrimental to the national interest, to that of the company, and to the individual. If the words "nothin&apos; down" can give us the best human guarantee of safety, for however brief a time, let us adopt them at least in principle as our slogan in 1952. Production for preservation in &apos;52 - but NOTHIN&apos; DOWN!

Jan 1, 1952

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake&apos;s drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake&apos;s waters previous to 1915. Most of this material

Jan 1, 1921

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

By James A. Barr

When phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. TO attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per ccnt. of available phosphate, which, howrever, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney formation, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss. One of the largest temporary losses in the industry occurs in the Florida pebble district where the recovery of phosphate runs about 25 per cent. The loss is classed as temporary because most of the tailing has been collected in ponds and piles, where it may be reclaimed in the future should developments or improved processes warrant. In cleaning the Florida pebble phosphate, aside from the elutriatisn

Jan 1, 1916

By W. J. Sharwood

(San Francisco Meeting, September, 1915) CUPELLATION is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead. oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus. in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by au addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connecting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated.

Jan 8, 1915

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

By M. Roy, Y. Roux, R. McIvor

"La Compagnie Minière Québec Cartier at Port Cartier. Quebec, utilizes six parallel wet grinding open circuit ball mills to grind iron ore concentrate for the pellet making process. In an attempt to improve grinding efficiency, a mix of 605 25 mm (1 in.) and 405 38 mm (1 ½ in.) grinding balls was charged to mill D while the opposite mix was used in all the other mills. Because media costs were higher for mill D, it was necessary to find out if the smaller balls provided a net economic benefit. Therefore, a test program was undertaken to determine the relative efficiency of the charge in mill D compared to the other grinding mills. Mill F was chosen for comparative efficiency measurements.The first problem was to choose a suitable definition of grinding efficiency. In management&apos;s view, previous attempts to quantify milling performance using population balance modelling were ineffective because they were unable to relate breakage rate functions to grinding circuit economical in any meaningful way. Work index analysis was also not favoured because of a number of complicating effects, including the fineness of the feed and product streams and open circuit grinding.It was decided to adopt a recent innovative approach which had been successfully applied to closed-circuit ball milling. For ""functional performance analysis of ball milling"" (McIvor et al., 1990; McIvor et al., 1991), a size criterion is first chosen to define ""fines·&apos; and ~&apos;coarse particles"". In this case 45 microns (325 mesh) was chosen to distinguish fines from coarse material. The relative grinding efficiency of each ball mill environment would then be ~e cumulative grinding (disappearance) rate of coarse (plus 45 nucrons) material per kilowatt hour of energy applied to the coarse material in the mill, divided by the grindability (measured in the laboratory) of the coarse material in the mill feed.Because the disappearance rate of coarse particles is also the production rate of fines, the following equation can be written for the efficiency of the mill environment, Effe, as defined above:"

Jan 1, 1994

By Farouk Tedjar

The growth of miniaturization in one hand and energy density need lead to rapid development of new chemistry for batteries as observed during last decade particularly in secondary systems. However dark side of the progress is always in environment impact and scarcity of resources. In the lithium segment a jump from six electrochemical series (all non rechargeable systems) before 1990 to more than 15 systems including new rechargeable systems has been observe during last decade. Lithium battery chemistry was enriched with new electrolytes, conductive salts and new oxide composition. In the same time, lithium ion battery safety was strongly improved during last period. The progress of these technologies was strongly boosted by the substantial growth of the mobile telephone market in the mid 1990&apos;s (+ 1% a month in 2000, and a 71% penetration rate in Europe in 2005 compared to just a few percent in 1996). This market is constantly in search of higher electrochemical performance (mainly energy density in front of increasing miniaturization. Recycling of end of life product could be managed not only in environment aspect, but also under resource conservation and economic aspect of arising technology (mainly on the effect of re-injection recovered materials) The Li-ion segment is a new branch in the cobalt market and impact of LiCoOx will be fitted with the actual increase of the demand for this battery. For this reason all the processes aim to valorize active and packaging material. RECUPYL process project was conducted in this direction to offer a new solution for recycling those lithium systems. The process has been developed at pilot industrial scales using synergy between new equipment (for mechanical pre-treatment step) and existing line at RECUPYL facility (for chemical treatment) and should lead to high valorization rate with a minimum hazardous co-products. The process was also developed in order to be able to recover news cathode materials introduced in electrode like LiFEPO4, LiMxCoyO2 and new anode composition in substitution with former carbon anode.

Jan 1, 2006

By M Rimes

This paper describes a technique to predict achievable head grades and likely variances from target grade for the Shovelanna Iron Ore Project, in the Pilbara region of Western Australia. The block model from which the production schedule is produced was created from a wide spaced drilling program and was classified as an Inferred Resource under the JORC Code. Ideally, production schedules and target grades would be determined using a combination of Proved and Probable reserves. However sometimes it is necessary to consider the requirements of potential off-take parties who have specific grade tolerances. A technique is needed to simulate mining sequences and grade variations early in the planning process, using an æexplorationÆ block model rather than the normal æminingÆ block model. Marketing contracts require examination whether the target grade {Fe, P, SiO2, Al2O3 can be kept constant, or must be revised during the life of the mine. A model (written in ExcelÖ using Visual Basic macros) develops a feasible, close to optimal, mine plan from block model data. Cut-off grades for minable ore are chosen. The model evaluates ore tonnage, grade and stripping ratio against depth. Outputs at this stage include plots of slices through the orebody, at nominated x, y and z coordinates, showing ore grade, waste, drill hole locations and topography. The model then searches for a feasible satisfactory mine plan. The initial grade target is the average for the identified ore blocks. The available block list (ABL) at any time is the set of ore blocks, any one of which can be mined without removing any other ore block. The entire initial ABL has an unacceptably large ætotal grade stressÆ, defined as [(Grade-Target)/Tolerance]2, summed over the four relevant minerals {Fe, P, SiO2, Al2O3}. The model trims the ABL, removing the block most harming the total stress. Trimming is repeated until the total grade stress reduces to an acceptable level. The trimmed ABL defines the first mine campaign. Removing the trimmed block set, a second ABL is exposed, which is again trimmed and mined. The process is automatic: a few seconds computation provides a complete mine plan. Re-running the model with adjusted grade limits quickly shows whether a uniform target can be achieved or whether the target must be modified during the mine life.

Jan 1, 2007

XstrataÆs Mount Isa Copper Operations (MICO) is a world-class mining operation producing in excess of six million tonnes of copper ore per annum from its underground mining operations. The Mount Isa Copper Mines have been producing from the underground operations since 1952. Current copper reserves are 87 million tonnes at 2.8 per cent Cu, extending the mineÆs life beyond 2018. The underground orebodies in the copper mines are divided into nine distinct areas and are mined by sublevel open stoping techniques. One of the nine areas is the hanging wall lens, which consists of two sections; a northern lens (NHWL) and a southern lens (SHWL). The SHWL has a proven reserve of 2.2 million tonnes with an average grade of 2.9 per cent copper. Stopes in the SHWL have an average size of approximately 245 000 tonnes and will be extracted in a primary-secondary mining sequence, producing ore until 2009. This paper discusses various aspects of stope design applied in the southern hanging wall lens, including sequencing options and the rationale for the selected sequence. Design features are also discussed and how they have evolved as more is learnt about the SHWL orebody. These include mass firing techniques, focusing on minimising ground vibrations, using seed wave form analysis and prediction. Rock mechanics issues will also be discussed, in particular the reinforcement of stope hanging walls and the use of instrumentation to monitor behaviour within the hanging wall.

Jan 1, 2006