Search Documents

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

By John F. Elliott

Six major trends that have had and are continuing to have major effects on the use and supplies of pig iron and scrap in the United States are (a) gradual replacement of the basic open hearth furnace (OH) by the basic oxygen furnace(BOF); (b) use of the electric furnaces for the production of plain-carbon steels, a trend which is closely related to the first; (c) United States changing from being a net exporter to a net importer of steel; (d) replacement of ingot casting by strand casting; (e) increased exportation of scrap; and (f) the lack of growth of the capacity of the U. S. steel industry to produce pig iron in the last 5 to 8 years. This report gives an analysis of the relationships between these trends and the use of processes for the production of raw steel in solidified form.

Jan 1, 1975

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

By O E. Jr Crenwelge

Frequency domain, single-charge vibration signatures are used to interpret the characteristics of explosive impulse excitation and ground vibration transmission. The effects of charge height, charge splitting, and different blasting agents are first discussed. Then the effects of rate of change with distance of overburden material properties and layer or surface geometries are illustrated.

Jan 1, 1988

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

Development of Cost-Efficient Environmentally Sound Technology for Enhanced Gold Recovery from Rebellious Gold-Containing Raw Materials Study of biochemical leaching performances in gold-bearing sulfide minerals processing enabled to develop environmentally sound technology of enhanced gold recovery from rebellious gold-containing raw materials. It was found that the ?-10 IMO bacteria activity contributes to increasing system oxygen concentrations and incrementing in rates of oxygen delivery onto surface of gold-bearing minerals. Bacteria activity products, ie, amino acids (?), support the formation of such heterocomplexes as [A-Au-CN]- , providing additional gold recovery into solutions. Technological properties of proposed bacteria solutions were studied. It was found that the proposed bacteria inoculants are capable to growing directly in process of raw materials leaching within a large pH range of media containing cyanides and thiosulfates. They oxidise the sulfur to the sulfate, as well as the antimony (III) and arsenic (III) sulfides to the pentads. For the first time, the hydrophobic cell properties, metabolites emulsifying efficiency, adsorption properties, wetting ability, surface tension and electro-kinetic potential of new bacteria strain solutions were studied as compared with chemical solutions. It was found that the proposed bacteria inoculants reduce surface tension at the solvent-mineral and solvent-concentrate phase boundaries. All aforementioned effects enhance mass transfer processes efficiency. IR-spectroscopy of new bacteria strain culture liquid allowed identifying available amino acids which substantially contribute to heterocomplex anion [A-Au-CN]- formation. Active involvement of heterotrophic bacteria in gold dissolving processes was identified. It was shown that the structure of metals complexes is substantially modified at intensive pulp agitation and during long-term storage. Fractional order reaction in biochemical and chemical gold leaching was identified. It evidences that the gold and impurity metals dissolving processes advance in synchronism. The both processes are running in diffusion zone. Biochemical leaching has advantages over chemical leaching, ie it provides enhanced rates of precious metals dissolving, improved gold recovery by 20 - 30 per cent, decreased cyanide consumption by 50 per cent. At the same time it allows to decontaminate dangerous substances contained in productive solutions produced in rebellious gold-containing raw materials processing. Basic parameters of flotation concentrates leaching by heterotrophic bacteria-assisted processing technology were tried and tested. Technology of gold sorption from leaching solutions was successfully tested.

Sep 13, 2010

By Stacy Loizeaux

The Beirut Hilton Hotel, which was built in 1975, but never occupied, was imploded on Sunday, July 14, 2002 by Controlled Demolition, Inc. (CDI) of Phoenix, Maryland and their client, Optimal Engineering Consulting & Contracting, SARL, (OECC) of Antelias, Lebanon to make room for a new hotel. Twenty-seven years ago, just days before the grand opening, the Hilton Hotel became the site of fighting in Lebanon’s Civil War. Christian and Muslim militiamen fought room to room for control of the building and other nearby hotels. The Hilton, two other major hotels and other high-rise buildings were ravaged by the fighting. The building was one of the three major hotels badly damaged, but not rebuilt, in Lebanon. Located in the City Center, the Hilton stood out in a major redevelopment area which, in recent years, had erased the scars of the 15 year long Civil Wa r.

Jan 1, 2003

By J. C. Carrasco, M. Sánchez, R. Jara, F. Marquez, F. Parada, R. Parra, J. Palacios

In past years, Chile has been the largest copper producer in the world and for 2002 mining represented country average of 10 % of the GDP, accounting for 47 % of the total exportation. As copper sulphides are the main mining resources in the country, the metal is produced using the classical processes of flotation and pyrometallurgical extraction. Seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country produced1,522,000 metric tons of fine copper in 2002, approximately one half of total copper concentrate production, with a notorious environmental impact due to the great amount of slag produced during these extraction steps. In this work, a global characterization of copper pyrometallurgical slags produced and disposed of in Chile and worldwide is done, and the concept of total project development is considered to explain the scopes of the study, recovering different compounds and generating new activities around mining. The presentation is completed with the proposal of various methods and techniques being developed today in a joint project between smelter plants and the University of Concepción, with the support of the Chilean government and mining companies, addressed to generate new materials from copper slag. Recovery of copper, molybdenum, precious metals, silica and iron, that is the most abundant component of the slag, are the goals for this research. Metals, commercial compounds, alloys and different forms of iron oxides for steel industry are proposed products.

Jan 1, 2004