Search Documents

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By S. Oglesby, A. L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are not immediately available at the time the sample is taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily corre-

Jan 1, 1960

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

The Committee submits the following report: The General Committee met in the Treasury Building at Washington on Oct. 6 and 7, 1919. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary of the Committee. Subcommittees were appointed on Invested Capital, on Mine Valuation, and on Depletion and Depreciation. These subcommittees were directed to meet separately and to report on Oct. 7 to the General Committee. On Oct. 7, the reports of these committees were submitted to the General Committee and on motion were received and referred to the Executive Committee for its information to be used as it deemed wise. A motion was carried that the Executive Committee be constituted a permanent committee to continue the work of the Committee, with full power to add to and increase its membership; that as thus increased it should constitute a permanent organization to act and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Committee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, Office of the Commissioner of Internal Revenue, Washington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St. New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, care of Engineering & Mining Journal, 10th Ave. and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, care of Peabody Coal Co., McCormick Building, Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City.

Jan 1, 1923

By Walter Miller

Developments in oil refining were so varied during 1938 that a refiner had to be alert or be left behind. The long-talked-of conversion of oil refining into a true chemical industry using petroleum as a raw material was hastened, particularly in the realm of motor-fuel manufacture, by the increased understanding and use of catalytic processes. The petroleum refiner's vocabulary has been extended to include alkylation, cyclization, aromatization, and isomerization. There are other devel: opments of a similar nature, but these are now considered commercially feasible under proper conditions. New Equipment Less expensive equipment and processes encouraged new construction and replacement. Estimates of money spent in the United States on building new plants and remodeling existing installations during 1938 place the sum at not less than $200,000,000, a noteworthy amount in a year marked by a business recession. The commercial application of small-scale catalytic polymerization of refinery gases made one of the latest advances available to the smaller operators, who usually are faced with unit installation and production costs higher than the large refinery enjoys. Competition was thereby fostered. Outstanding in this respect was the construction of two or more polymerization plants in small refineries at extremely low installation costs, with amortization measured in months instead of years. Houdry Processes Bursting like a bombshell late in the year was the disclosure of the extent of the development of the Houdry processes of catalytic cracking, viscosity breaking, gasoline treatment, desulphurization, and polymerization, said to be applicable to almost any raw petroleum stock and yielding gasoline of exceptionally high octane number. This process is claimed to be particularly adapted to once-through cracking of aliphatic hydrocarbons, and when combined with any of the conventional thermal

Jan 1, 1939

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events, and so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the body of knowledge captured from diverse mining industry experts for the management of unwanted strata incidents, and explosions in the underground environment. This knowledge is divided into a series of initiating events within both topics (as listed) with further degrees of classification based on design, operation, and management concerns. Strata Underground Initiating Events: Explosions Initiating Events Loss of strata control at longwall face Fire or ignition in a sealed area Loss of strata control in outbye roadways Fire or ignition in an unsealed goaf area Loss of strata control in roadways under development Fire or ignition in an extraction face Loss of control of overburden and caving behavior Fire or ignition in outbye Loss of pillar system stability Loss of control of goaf edge in pillar extraction Fire or ignition in a development panel or first working Loss of strata control in shafts The system guides the user in generating substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By Ralph Hultgren

A CONSIDERABLE interest in the subject of superlattices has been mani-fested by many papers and reviews that have recently appeared, both in physical and metallurgical publications. This interest is due largely to the apparent simplicity of the ordering process, which permits the explana-tion of many phenomena on the basis of elementary theory. Moreover, ordering may cause important changes in the physical properties of alloys. In this paper, we shall discuss the causes of superlattices in terms of simple properties of the elements that give rise to them, together with a series of experiments performed to test our conclusions. Evidence is presented that in some cases the process of ordering is more complex than might be supposed. While the different species of atoms are usually found in random posi-tions in alloy lattices, in some cases unlike atoms tend to be nearest neighbors. Bethe'st "order of neighbors" is a statistical measure of this tendency. At suitable compositions it is possible for atoms in large regions to be regularly arranged, which causes superlattice lines to appear in X-ray diffraction patterns. Bragg and Williams2 have dealt with this "long-distance order" in their fundamental work on superlattices. Excellent discussions of superlattices are to be found in current reviews.3,4

Jan 1, 1939

By C Rogers

"The Coal Seam Gas (CSG) industry has seen a rapid increase in activity over a 30-year periodfrom the early 1990s within Australia. Despite public concerns over environmental issues, theCSG industry has increased in Queensland to the point where more than 90 per cent of naturalgas consumed in Queensland is CSG. The New South Wales (NSW) CSG industry has been slowerto respond for many reasons. Ninety-five per cent of natural gas consumed in NSW comes frominterstate. However, CSG activity in New South Wales is increasing notwithstanding publicconcerns. The CSG potential of three Petroleum Exploration Licenses (PELs) are being assessedwithin the Southern Sydney Basin that provides a unique opportunity to develop resourcesstrategically around many abandoned coal mines. The question has been asked - what do theseabandoned coal mines mean to the project? Are they good or bad? Are they friend or foe? Thispaper att empts to answer these questions and in doing so describes the coal mine ventilation andgas management philosophies and practices used to assess gas production potential. The coalmining philosophies not only have the potential to assist in the construction of a highly successfulCSG project, but they also potentially add signifi cant pre production value by re defi ning how theresources and reserves are assessed and therefore valued. The behaviour of abandoned coal minesand the goaves within the PELs are not well understood by the petroleum industry. However, in the Illawarra region there is an abundance of coal mining knowledge and expertise that if properly focused can greatly increase the chances of project success."

Jun 1, 2012

ZAY JEFFRIES, Cleveland, Ohio (written discussion?).-The authors conclude that there is a certain average size of precipitated CuAl2 par-ticle which produces maximum strength and hardness in duralumin; that when the size of particle is smaller or larger than this particular size the hardness decreases. The writer agrees with this conclusion, because it seems to he directly indicated by the facts. Why does duralumin present this apparent discrepancy? Let us con-sider some physical aspects of the precipitation of CuAl2 from a saturated solution on cooling. When a molecule of CuAI3 is removed from the solvent, or matrix, and added to another group of CuAl2 molecules, as is known to occur on slow cooling, the forces of adhesion between the CuAl2 molecule and the solvent have been exceeded. Since a. change in tem-perature only is sufficient to cause precipitation, it must also be sufficient to cause the loss of adhesion bonds between the excess CuAl2 molecules and the solvent, or matrix. Lost adhesion bonds means loss of cohesion of the mass as a whole. When duralumin is cooled from 500° in a furnace, globules of CuAl2, large enough to be seen easily with a high-power microscope, are formed. There are, however, globules so small as to be hardly distinguishable, and others too small to be resolved are suggested by the non-uniformity of the surface appearance of the section. As the smallest globule of CuAl2 resolvable with a high-power microscope contains about 2,000,-000,000 molecules, it is evident that with rapid cooling submicroscopic particles of CuAl2 must be present in large numbers; in fact, after quench-

Jan 12, 1919

By D. S. Cahn, D. W. Fuerstenau

Specimens of glass, plexiglass, and naturally occurring minerals were irradiated by a 15-joule ruby laser pulse to determine criteria for the fracture of nonmetallic solids by internal thermal stresses. Fracture did not occur in those specimens with either a very high or very low internal absorptance or with a high spectral reflectance. If significant amounts of melting and vaporization do not occur at the surface of irradiation, the specimen will fracture if a derived 11fracture stress" exceeds the ultimate tensile strength of the specimen. The purpose of this investigation was to determine criteria for the fracture of nonmetallic solids by internal thermal stresses which are caused by absorption of laser irradiation. A laser produces a very short pulse of light which has a high energy density distributed over a very narrow part of the visible spectrum. The laser system used in this investigation had an energy output of 15 0 joules at a wavelength of 6940 A. Fracture in a non-metallic solid, then, would be caused by the absorption of light energy by that solid, and subsequent conversion of this energy to heat or mechanical energy. Fracture is caused by internal stresses that result from rapidly imposed nonequilibrium thermal gradients. ANALYSIS OF CONDITIONS FOR FRACTURE BY LASER IRRADIATION For this analysis, the laser beam is assumed to be circular and centered on the junction of the major and minor axes of a rectangular specimen. The laser beam forms a cylinder of radius rb extending through the specimen width. The beam cylinder may be then thought of as a heated mass constrained by a surrounding unheated mass. The instantaneously heated cylinder will at-

Jan 1, 1968

By Gail B. Knight

INTRODUCTION In May 1984, The Canadian Pacific Railway awarded to the Joint Venture of Foundation of Canada, Ltd. of Toronto, Atlas Construction Co. of Montreal, and S. A. Healy Co. of Chicago the contract for the construction of 27,000 ft of tunnel starting from the east portal. Selkirk contractors, the Joint Venture of Foundation, Atlas and Healy, which had successfully completed for CPR in 1983 the construction of both portal structures for this tunnel, studied several different alternative proposals before presenting its bid pooling each individual company's technical resources and experiences. (Foundation had just completed in association with other companies a similar tunnel project in British Columbia, and the S. A. Healy Co. could provide its experience of more than 40 miles of tunnels excavated by full face boring machines.) Among the alternatives investigated there was a fully circular tunnel to be excavated by a 30 ft diameter TBM, a full section drill and shoot proposal, and a mixed alternative, the "key hole" proposal, consisting of a TBM driven circular top heading followed by benching to design size. Technical, geological and economical considerations determined the alternative that was eventually proposed to CPR. HISTORICAL NOTES The tunnel construction parallels an existing tunnel through the Selkirk mountains that was excavated in 1885. In order to reduce the grade to 1% on the heavily loaded west bound trains, the new tunnel was at a lower elevation and lengthened to almost 9 miles. GEOTECHNICAL INFORMATION CP Rail site investigations began in 1978. The surface rocks in the tunnel construction area are metamorphosed Cambrian and Pre-Cambrian sediments; the underlying formation contains fine and coarse grained rocks presenting different degrees of metamorphism. The

Jan 1, 1987

By E. C. Roberts

TO facilitate some recent microscopic investigations it was necessary to devise special mounting techniques for the polishing of two quite different metallographic specimens. These techniques are extremely simple and are submitted for whatever value they may be to other investigators. The first specimen mount proved very satisfactory for the study of untempered martensite. Since it was undesirable to heat the specimen, lucite or bakelite mounting materials could not be used in the conventional manner. A cold mount was made by drilling a hole of the same diameter as the specimen in a cylindrical piece of polystyrene then press- ing the steel specimen into the hole on an ordinary vise. A prefabricated disk of lucite should work equally well. The only precautions necessary are that the hole be drilled out cleanly and the piece of steel be pressed into the plastic uniformly, otherwise the mount will crack. The second type of mount was required for the study of slag specimens by reflected light. Mounting these specimens in bakelite and then attempting to rough finish the surfaces on graded emery papers resulted in a considerable amount of chipping and breaking out of the slag particles. This made further satisfactory polishing almost impossible. It was found, however, that if the bakelite-mounted specimen was first rough finished to a point where a good specimen surface became visible, the interstices in the specimen surface could be filled and the polishing completed. This filling was accomplished by placing a small amount of lucite powder in the bottom of the steel specimen mold then reinserting the bakelite-mounted specimen on top of the lucite powder. Reheating the mold to the proper temperature and applying the required pressure resulted in the formation of a thin disk of lucite on the bottom of the bakelite specimen. By carefully grinding the lucite away a uniform surface including the slag specimen was obtained and further polishing was unhampered by slag disintegration.

Jan 1, 1951

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By J. D. Audley Smith

Heine's " blue test" for copper, as described by the authorities generally, calls for a set of standard colors; and there has been some discussion concerning the relative superiority, for this purpose, of sulphate and nitrate solutions. The whole matter evidently hinges on the preservation of the standard colors in well-stoppered bottles. The apparatus described by Q. L. Heath* cannot be much improved, when very accurate readings are required. The following method was devised for the purpose of doing away with preserved sets of standard colors, by making a fresh standard for each batch of assays. The solutions are prepared in the usual way, each ammoniacal solution being filtered into its separate bottle, and then filled up to the containing-mark and thoroughly mixed. A similar color-bottle, with an " S " etched upon it, to distinguish it from the other bottles, which are numbered to correspond with the samples, is kept to run the standard. About 150 C.C. of water is put into it, and then the amount of acid (sulphuric or nitric) present in each determination, followed by 30 C.C. of ammonia (s. g. 0.90), which should make the mixture strongly ammoniacal. The liquid is now made up almost to the containing-mark (200 c.c.), say within 1 C.C. The lowest assay is selected first and placed alongside the standard, which, at the beginning, contains no copper. A copper-solution is then dropped into the standard from a burette ; and after each addition the bottle is well shaken and compared with the assay-sample. This operation is repeated until the two shades match exactly, when the burette is read and the assay-result is calculated. The assay next in order of depth of color is now taken and treated in the same way, and so on, until the batch is completed. It

Jan 1, 1901

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By David Dreisinger

The pressure oxidation of pyrite is an important hydrometallurgical technology, especially in the total oxidation of refractory gold ores and concentrates (gold is locked in the pyrite structure preventing direct cyanide recovery). It has been noticed in some commercial applications and benchscale studies that the leaching of pyrite may be slow and apparently can be inhibited by the presence of molten elemental sulfur in the leach pulp. The purpose of this study was to determine whether Ortho-Phenylene-Diamine (OPD) could be used as a surfactant or dispersant for sulfur in the pressure oxidation of pyrite. OPD has previously been shown to be useful for pressure leaching of zinc and copper sulfides at 150 C.In this work, the interfacial chemistry of sulfur was studied at temperatures of up to 190 C in the presence and absence of OPD and other surfactants. The contact angle between molten sulfur and pyrite was also measured. Finally, the impact of OPD on the kinetics of pyrite oxidation was measured in bench-scale pressure oxidation experiments. The essential finding of this study was that OPD lowers the interfacial tension between molten sulfur and acid solutions and increases the contact angle (reduces wetting) between molten sulfur and pyrite. The work of adhesion between sulfur and pyrite was reduced by more than an order of magnitude in the presence of OPD. In bench scale tests, addition of OPD was found to significantly accelerate the rate of oxidation of pyrite. Conveniently, it was found that OPD was also fully degraded during high temperature oxidation processes. No residual OPD was detected in solution or solid samples from the leach testing. OPD is recommended as a sulfur dispersant in the pressure oxidation of pyrite and/or elemental sulfur containing feeds.

Jan 1, 2003

By Richard M. Michaels

In considering the use of underground space for civil works functions, there are several criteria that must be met if transfer of any of them is to occur. It is important to recognize that these criteria involve social and political as well as conventional engineering and economic considerations. It is the purpose of this report to identify certain of these criteria and develop a set of measures that will permit the evaluation of the potential benefit of transferring civil works functions underground. The work reported here was completed for the ASCE and is contained in the report, Undergound Space, 1973. If one examines the total direct and indirect economic return from the location of civil works in subsurface rather than surface space, sizeable benefits accrue. This occurs largely because design, construction, operating and maintenance costs of these systems are highly dependent upon the forces exerted on these systems by the surface enviroment itself. Transferring of these facilities to underground space would eliminate a large segment of those costs. It is equally true that civil works functions compete with other uses for surface space and generate significant conflicts with these competing uses. Highway construction takes land from other productive uses. Electrical transmission lines conflict in terms of safety and aesthetics with adjacent social activities. Assuming that construction costs can be made equivalent, the analyses in the previous report indicate that the locating of all civil works functions underground would yield an annual net savings to the society of the order of 60 billion dollars. It may be added that the benefits in terms of improved social perfromance would also be substantial. However, it is clear that the benefits from utilization of subsurface

Jan 1, 1974