Search Documents

By Wadsley MW

The Greenhouse Effect, with its potential for global warming, is strongly linked to industrial carbon dioxide emissions. Global carbon mass balances indicate that absorption in sea water is the major natural sink of carbon dioxide. However the surface waters of the oceans are close to chemical equilibrium with the atmosphere with respect to carbon dioxide, while the deep ocean waters are not. Consequently, the transfer of carbon dioxide from the surface limits the rate at which the oceans can absorb carbon dioxide. It is proposed that direct transfer of carbon dioxide from industrial installations to deep ocean waters be evaluated as an interim measure to slow the rate of increase of carbon dioxide concentration in the atmosphere and hence allow time for the development of sustainable industrial practices. As an aid to thinking on the development of suitable technology, equilibrium calculations are presented which demonstrate that sea water in equilibrium with flue gases will dissolve six times the quantity of carbon dioxide that is dissolved in equilibrium with the ambient atmosphere. Sea water saturated with calcium carbonate and in equilibrium with flue gases will dissolve 20 times the quantity of carbon dioxide that is dissolved in equilibrium with the ambient atmosphere. However the absolute concentrations of dissolved carbon dioxide are still very small.

Jan 1, 1989

AT the meeting of January 28 which was held too late to be reported in the February MINING AND METAL-LURGY, Messrs. Taylor, Barron, Bassett, DeGolyer, Hutchinson, Norris, Rand, Reynders, Smith, Sweetser and Callow were present. Aside from routine matters, relating to finances and membership,, the Board author-ized establishment of a payroll account and payment by check. It also approved plans for a regional meeting to be, held at Cleveland on April 19 and 20 under the auspices of the Ohio Section and the Iron and Steel Committee. Following a report from the Committee on increase of Membership, Messrs. Barron, Bassett, and Sweetser were appointed as a special committee to con-sider the feasibility of increasing the dues. Mr. Read was made secretary of this Committee. A pleasant feature of the meeting was the presence of past-presi-dent Olcott and the presentation by him to the Institute of an elaborate scrap book, covering the excursion through Mexico made by the Institute in 1901. The meeting was preceded by a dinner at which Scott Turner spoke of the problems of the Bureau of Mines and the large volume of service work for the govern-ment it was now called on to perform. M. L. Requa discussed the need of more exact data covering our national reserve of minerals. E. N. Cooper gave a vivid picture of conditions in Mexico. W. H. Bassett told of the problems before the Institute of Metals, and Zay Jeffries told of the plans for that Division now being formulated. Max W. Ball reinforced what Mr. Requa had said relative to the importance and value of conservation studies as relates to minerals.

Jan 3, 1927

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By D. Magoon

The metals industry has enjoyed a resurgence in prices and demand for its commodities during the global surge in economic activity that began in 2005. This success has brought with it an unprecedented demand for professionals in all sectors of our economy. Nowhere is that more true than in the mining and metallurgy sectors. However, this welcome improvement follows on the heels of almost two decades of challenging markets for the mining and metallurgy. Our sector's protracted economic slump created a paucity of demand for professionals that had several consequences. Our industry came to be viewed as a low ?tech, uninteresting place to work. Low demand for professionals encouraged students to seek other career options. Reduced demand for graduates, coupled with diminished program funding by our sector, resulted in dramatic shrinkage in university mining and metallurgy programs. This paper explores the lessons to be learned from our recent economic history and discusses some strategies for addressing our image issue. Attracting and retaining good employees is also strongly influenced by a company's reputation and record as a good employer. This reality is very well illustrated by the findings of an international survey undertaken by Towers Perrin in 2005 of 86,000 employees of mid-sized and large companies in 16 countries. The key findings related to attracting and retaining employees are presented. These findings are also discussed in the context of their specific applicability to the mining and metallurgy industry.

Jan 1, 2007

By T. Puhakka

Simulation is a way to obtain quickly today future information on how planned systems will most likely behave in various selected situations. This information may then be used to optimize the system and its components and maximize the performance and output. Simulation is a way to fine-tune the layout, match the mobile fleet and optimize the schedule and the way of working to meet the desired production requirements. Simulation provides a glimpse of the upcoming operation, ‘future today’ and helps to predict its restrictions and sensitivity to various aspects. OptiMine™, the Sandvik Tamrock Corp. and CyberCube Oy developed simulation tool is designed to simulate underground rock flow and match suitable technology with various layout options. This tool can be used to view what-if situations and determine what kind of impact mastered changes have to production. The findings of critical points in the layout and working procedures at an early stage of a new mine can help to optimize the layout and material flow. OptiMine™is modular based simulation tool that combines the supplier machine knowledge and traffic guidance with mine operational know-how and mine environment. It is developed to work in a way that an effect of an individual incident, such as the effect of one additional turn in a continuous loading cycle to the daily capacity can be identified. The reported output can be used for economical impact evaluation of selected options. This paper discusses the use of simulation in general and the way the OptiMine™ simulation tool operates and how it may be used for operation, technology and material flow optimization.

Sep 1, 2001

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractor's and owner's perspectives and focuses on: ? when performance tests are required, ? what type of performance test/warranty is optimum for each type of project, and ? how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between owner's risk and contractor's risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the owner's corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide `common purpose' early in the contract negotiation process.

Jan 1, 2007

By J. T. Cherry

A fundamental goal of the Plowshare Program is to predict crater dimensions when an explosive of known yield is buried at a given depth in a given medium. In this paper a technique is presented that seems to calculate adequately, from first principles, the mound and cavity growth that occur during nuclear and high-explosive cratering events. The technique features a standard, numerical approach to high- intensity stress-wave propagation coupled with a unique model of material behavior in brittle failure. A schematic of stress-wave propagation is presented in Fig. 1. The equation of motion provides a functional relation between the applied stress field and the resulting acceleration of each point in the medium. Accelerations, when allowed to act over a small time increment [A]t, produce new velocities, velocities produce displacements, displacements produce strains, and strains produce a new stress field. Time is incremented by [A]t, and the cycle is repeated. The time increment [A]t is determined by an independent stability condition which requires the increment to be smaller than the time necessary far a compressional wave to travel across the smallest zone. We assume that failure occurs in a brittle material when either the tensile strength or the maximum allowable strain energy of distortion is exceeded. When either of these two conditions is violated, the code uses the cracked equation of state to determine the stress. A preshot testing program is used to determine the consolidated and cracked equations of state. In situ properties to be determined by field logging are density and elastic velocity (compressional and shear ve-

Jan 1, 1967

By P. Schiavi

A trend towards the independent verification of sustainable development reporting and assessment using third party certification can be discerned in the global minerals industry. Various codes that provide for the third party assessment and certification of performance against a range of externally developed sustainability indicators are being adopted by minerals companies, and there is also considerable activity in the broader area of third party assurance. Using a sociological approach, this paper examines the reasons why third party certification schemes are appearing in the minerals industry to address sustainable development imperatives in preference to other forms of regulation, and considers the broader implications of this trend. Data are drawn from a series of qualitative, in-depth interviews conducted with some of the key players in the development and adoption of certification schemes in the minerals industry, with executive managers of a range of large mining corporations, with representatives of global non-governmental organizations that are active in mining issues, and with government officers responsible for the regulation of mining corporations in Australia. Factors responsible for the emergence of the new certification schemes include: increasing demands from stakeholders for greater credibility in reporting against sustainable development indicators; broader contextual factors including globalization and neoliberal policies; and issues relating to trust and risk. Using insights from our research, and the work of others in this field, we identify some of the critical features of a credible third party certification scheme, and note some of the challenges for the design and implementation of such schemes. We conclude by discussing some of the broader implications of third party certification as an emerging form of regulation in the minerals industry.

Jan 1, 2007

By F. C. Eberhardt

Systematic planning of underground work is increasingly important in this era of advancement of rapid underground excavation techniques. The day when planning consisted of deciding which men would shovel and which would push wheelbarrows - and the answer to any problem was more men - has faded into the past. The modern underground constructor faces economic and competitive conditions which demand exacting planning, logistics and scheduling; the most efficient operating methods and equipment known; and realistic, comprehensive, analytical risk evaluation with adequate contingencies or other protection. Proper planning to cover all these elements - plus one other element: old fashioned "good luck" - will insure a successful underground project. Underground work, because of its inherent characteristics, is among the most risky types of construction. The forecasting of underground conditions is at this time only educated predictions based on sometimes faulty data, insufficient data, or no data at all. The predicted conditions of numerous operations have deviated far from the actual conditions encountered. Opportunities for error exist in profusion seldom present for surface operations. Other than this unusual risk factor, the planning for underground work does not differ greatly from planning for surface work. In planning and starting an operation there is seldom available the information or time to thoroughly analyze all unknowns. It then becomes necessary to develop a plan predicated on assumptions and trade-offs that appear to be safe and economical and to add time and cost contingencies that will provide some degree of protection. On competitively bid fixed price work, choice of markup on estimated

Jan 1, 1974

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013

By F. Aurelian

The Banat district in Romania was an important uranium mining area for the last 45 years until its closure in 1997. Uranium was present as finely dispersed pitchblende into solid bitumen lens and layers. Due to the mining activities, radioactive wastes have been disposed of in different places of the Banat area. These sites contain uranium, radium and radon and exhibit high contamination potential for environmental receptors (soil, air, waters, sediments and vegetation). Therefore the risk for human health through external and internal irradiation is considered high. The main pollution sources in this uranium mining area are mine and surface waters, waste and low grade ore heaps, dumps as well as release of radon. In this paper studies concerning recognition of pollution sources, delimitation of maps, uranium and radium solubilization and migration from dumps as well as environmental contamination of specific areas related to exploitation and exploration are presented. The risk assessment is based on the relationship ?source-pathway-target? in order to assess environmental risks and identify targets for rehabilitation. The sources causing significant contamination problems were identified by examining the pollutant linkage. The remediation plan for the Banat uranium mining complex involves mine flooding, treatment of water and leachates, as well as modification of heap slopes, application of covers and establishment of vegetation.

Jan 1, 2005

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By D. Bizier, B. H. Gardner, Y. P. Wang, S. Serata

As part of an ongoing effort to develop more cost-effective and “user friendly” hardware for geomechanical measurements required for underground mine design, Serata Geomechanics, Inc. (SGI) has investigated the potential of borehole pressure cells (WCs) for in situ measurement of stress states and continuous monitoring of changes in ground stress. In particular, because of certain advantages gained thereby, WCs utilizing an elastomer, instead of metal (e.g., copper), for the skin of the pressure cell have been developed. A data analysis technique for determining ground stress state directly from BPC data has been developed. This technique has been tested for salt ground through both in situ applications and computer simulation analysis of the BPC/borehole boundary interaction. This paper discusses the data analysis technique, the results of field and computer simulation testing of its validity, and evaluates the advantages of elastomeric BPCs in relation thereto. It utilizes field data from recent elastomeric BPC applications in the salt mine at Goderich, Ontario operated by the Sifto Division of Damtarn Inc.

Jan 1, 1986

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

A mining joint venture presents a real management challenge to achieve harmony with the other participants in the successful development and operation of a mine. This can best be facilitated by a detailed agreement and guided by a set of joint venture principles which recognise the differences of the interests of the parties and seek to establish sound business and personal principles by which differences not anticipated in the agreement might be resolved. The major and minor co-venturers can and do present potential difficulties to one another. This paper, one of the pair in the joint venture panel discussion session, predominately presents the minor's viewpoint. Usually commercial matters such as project finance, areas of interest, divestment, pre-emptive rights and decision-making can be adequately covered in the agreement. However, when the parties disagree and have difficulty in resolving their differences, the joint venture principles should be used to advantage to resolve relationship difficulties.

Jan 1, 1997

By James R. Cost

The increasing emphasis upon the use of refractory metals has resulted in a closer look at some of the properties of these materials. In the course of a study of the Nb-N system it became necessary to re-examine one such property, the spectral emissivity, e. Experiments were performed in order to determine e for solid niobium as a function of both temperature and nitrogen content. The results of these experiments, which indicate a small but significant correction to the spectral emissivity of pure niobium, are reported herein. In addition, data on the total emissivity, et, of niobium and the spectral emissivity of the nitride Nb2N are given. To this author's knowledge, neither of these emissivities are as yet reported in the literature. Previous studies of the spectral emissivity of niobium have been few. In 1915, Burgess and Waltenburgl obtained a value of 0.49. Whitney? in 1935, used a Mendenhall V to obtain the commonly accepted value of 0.374. A recent investigation of sintering of niobium graphically reported a value of about 0.36= using a solid block of the metal with a blackbody hole drilled into it. In the present experiment a method similar to that of Worthing4 was used. An 8-in. long and 3/16 in. diam hollow tube was formed from smooth surfaced 0.0013-

Jan 1, 1962

By Ta M. Li

In Gila County, Ariz., the Jaquays Mining Co. still finds the mining of asbestos a worthwhile and economical venture. At a time when domestic productive capacity is being reduced because of rapidly rising costs and tough environmental dust standards, this firm has dramatically brought its mine and mill operation into full productive capacity and compliance with both Federal and State regulations. Jaquay's Mining Corp. owns four underground mines in the Tonto National Forest, located approximately 32 miles north of the Globe-Miami District in Arizona. Only one mine, the El Dorado, is presently active. It mines an estimated 45,000 tpy of ore and waste. From this figure about 3000 tpy of fiber (No. one crude to Grade 4T) and fiberized shorts (No, seven) are recovered at the firm's mill, located in Globe, Ariz. Based on current ore reserves, the El Dorado mine has an estimated life between 15 to 17 years, assuming current mining rates and stable market conditions.

Jan 3, 1975

By Migen Dibra

Antitrust and competition laws are designed to protect the free markets and promote competition in order to assure a dynamic and efficient economy and to provide competitive prices for quality products and services. They apply to mergers and acquisitions as well as to joint ventures especially among competitor companies who possess market power and these include collaborations on research and development. If it is determined that these actions are likely to substantially prevent or lessen competition the courts might dissolve, stop, alternate them, etc. Two new factors affect this process today: The role of new technologies and the markets globalization. They both have a considerable effect on the way these laws are interpreted by the courts and on their eventual amendments in order to reflect the new reality. A new applied technology and the globalization separately or together may change the factors that determine how anticompetitive a merger or acquisition between competitors may be and may also serve as a basis for amending the antitrust and competition laws. In this paper, a short review of the recent mergers and acquisitions of various companies has been carried out along with an abridged analysis of the current antitrust and competition laws in USA, Canada and European Union in the view of their capacity to handle the new reality. Some related court decisions are also examined and several examples are given in order to illustrate the influence of new technologies and globalization in interpreting the existing laws and on their amendment possibilities.

Jan 1, 2006

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994