Search Documents

By J. W. Markham, M. Atiemo, K. Yoshida

INTRODUCTION In open-pit mining of high grade ores, operators of mining equipment in a pressurized cab are protected from inhaling radioactive aerosols by the use of filtered air through a pre-impactor and a HEPA (high efficiency particulate air) filter. At present, a limited amount of scientific information is available on the worker exposure to airborne alpha emitters in the mining of high-grade ores. (Miller, 1977, Nielson, et al, 1979). Factors affecting the worker exposure to alpha radiation are: the grade of uranium containing ores, the environmental conditions inside the mine pit, the protection factor of the cab filter system, the workers' attitude towards the hazards of radioactivity and the adopted contamination control in the cabs. Four series of field samplings were conducted during the fall of 1980 and the summer of 1981 at a mining site in northern Saskatchewan to investigate the extent of protection an equipment operator has against cab internal exposure to airborne alpha emitters with short and long half-life radionuclides. The variation in the breathing zone concentrationnof aerosols as a result of resuspension is discussed, however no attempt was made to isolate and investigate the factors and the associated parameters of the aerosol resuspension phenomenon. AEROSOL RESUSPENSION IN A CAB Mechanisms of Resuspension [Sources]: The presence of radioactive aerosols inside a cab and in the breathing zone of an operator may be due to initial concentration inside [(CO)], concentration in the filtered (HEPA) air (CC, at the flow rate [QC]), the concentration of the aerosol through resuspension ([CR]), the aerosol concentration in the air outside the cab ([CE]) and the concentration of the aerosol in the leaking air [(CL)], at the flow rate of [(QL)]. [Volumetric Equilibrium]: Assuming a uniform concentration of the aerosol in the cab, the aerosol concentration in the breathing zone[ (CBZ)] may be expressed as, [CBZ+CO+CC+CR-CL] If [QC] remains greater than [QL], there is pressurization in the cab. There is particle loss as a result of the leaking air from the tight cab, however the condition of adequate pressurization ensures that [CL ~ CC]. Also for dust particles filtered through HEPA [CC – 0] thus [CBZ + CO + CR] For the radioactive gases, [CBZ - CO + CC] Over long periods,[ CBZ – CE] but if [CBZ] exceeds the value of CE then the aerosol build-up in the cab has, occurred. [Resuspension]: Turbulent bursts are generated within the core region of a cab confinement, such that the down sweeps and the up sweeps of the air bursts cause resuspension of dust from the surfaces. Particles initiate resuspension by four major modes: namely, sliding, rocking, rolling, bouncing or sudden ejection or by combinations of these. Nevertheless the adhesion force between the particles and the surface must be overcome by ejection forces before ejection takes place (Kline et al, 1967, Corino and Bradkey 1969, Kim et al 1971). The phenomenon of particle resuspension from a surface may be expressed in a generalized form as: CR =f (Uz . R . D . H) where CR = Rate of particle resuspension UZ = Surface shear velocity R = Surface roughness parameter D = Aerodynamic diameter of particle H = Frequency of surface airburst A detailed discussion of the individual parameters was attempted for the case of farm tractor cabs by Atiemo (1981), such a treatment is out of the scope of this study. Only the effects of the properties of surface roughness will be discussed. Effect of Surface Properties The roughness of the surface from which dust particles are ejected plays a significant role in the deposition and resuspension of the dust. The roughness or the amount of protrusions greatly influence the intensity of air turbulence in the immediate vicinity of the surface (Schmel 1976). For most roughened surfaces therefore, larger particles may be dislodged in greater quantities than smaller particles. The deposition and the resuspension of dust particles from different surface materials of glass, cloth, metal and rubber have been studied in a wind tunnel (Atiemo, 1981). Field Conditions Mining equipments used are: a backhoe, a bulldozer with ripper attachment and two dumptrucks for high-grade ore operations; a payloader and two dumptrucks for waste handling; and a jumbo drill which drills dynamite holes for ore blasting. All this

Jan 1, 1981

By G. D. Naugle, L. C. Atkinson

Introduction Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydrologic impacts resulting from the pit refilling with groundwater following the cessation of mining activity can also be significant. The prediction of the rate at which the post-mining pit will fill with groundwater is a critical aspect of assessing the long-term hydrologic impacts. Numerical groundwater flow modeling provides a method for predicting the groundwater refilling rate of the pit. The rate at which pit "lakes" fill depends on several factors: •the rate and duration of pit dewatering; •the depth and size of the ultimate pit and •the pre-mining hydrologic regime. These factors can be incorporated into a detailed numerical groundwater flow model that can then be used to assess the effects of dewatering and post-mining recovery on the local and regional hydrologic systems. A sufficiently detailed, numerical groundwater model provides the oportunity to: •account for complex geology near the pit; •assess the impact of active pit dewatering and •predict the long-term impacts of post-mining groundwater flow into the pit. A detailed groundwater model incorporating these items has been developed and applied at an operating open-pit mine. Developed by Durbin and O'Brien (1987), the three-dimensional, finite-element, groundwater flow model was used to represent the hydrologic system of an approximately 253-km2 (98-sq mile) area surrounding the pit. Historical groundwater elevation data, stream flows and meteorologic, geologic and geophysical data were used to establish the dimensions and initial conditions for the model. Steady-state conditions, representing the pre-mining local and regional hydrologic systems, were simulated using the initial conditions incorporated into the groundwater model. The groundwater model was then utilized to simulate various dewatering programs, to predict the filling rate and the groundwater depth in the ultimate pit once mining activities are complete and to assess the long-term impacts on the regional groundwater flow system. Development of pit lake model Groundwater modeling efforts were completed in two phases. The first focused on pit dewatering activities, while the second phase concentrated on the post-mining effects on the hydrologic system. The final estimates of groundwater elevations calculated during the pit dewatering simulations were used in predicting the post-mining recovery of the hydrologic system. The groundwater model was also modified prior to the second phase to account for the volume of rock removed during mining activities. To account for the actual volume of rock mined, the geometry of the post-dewatering model grid was modified to approximate the final pit geometry. The depth and width of the ultimate pit were divided into eight idealized stages that represented significant changes in the bench geometries. These eight stages were then introduced sequentially into the model according to the predicted water elevations within the pit. In this way, changes in the volume and depth of water within the pit were accounted for through time. Once the ultimate pit geometry was accounted for in the model, it was necessary to assign new hydraulic characteristics to those parts of the model grid (elements) that represented excavated rock. The solution of the numerical model requires that finite hydraulic conductivity values be assigned to the portion of the groundwater model that represents excavated rock. Therefore, the calculated groundwater elevations differ, somewhat, between the edges and the center of the open pit. These model-calculated water elevations at the edge and in the middle of the open pit represent the elevation of water that would occur in the pit lake. To minimize the error in the estimated level of water within the pit lake, the hydraulic conductivity was increased to a value that would: •minimize the predicted difference between the groundwater elevations across the open pit and •produce a numerically stable solution. Specific storage is the hydrologic parameter that accounts for the water produced by compaction of the aquifer matrix. To predict the groundwater volume that would flow into the ultimate pit, this parameter was assigned a value equivalent to the compressibility of water. This value of specific storage reflects the post-mining groundwater storage occurring as an open body of water. Additionally, a specific yield of 1.0 was assigned to the pit elements to represent the 100% porosity of the open pit. In

Jan 1, 1994

By W. T. Stuart

THE increased demand for iron ore has necessitated a re-examination of ore-bearing lands on which the presence of water previously has indicated hazardous and expensive operating conditions. In view of the importance of iron ore production to the national economy and defense, the Ground Water Branch of the U. S. Geological Survey, in cooperation with the state of Michigan, began a study of mine drainage in the Iron River district in 1945, and later extended the work to the Marquette district. The purpose of these studies was to define the principles involved in the movement of surface and ground water toward the mined areas, with the hope that the information obtained in the research would lead to the development of methods of water control and to a reduction in the total mining costs. Not only are the direct costs of drainage increasing, but also the indirect operational costs of working a wet mine are becoming a larger proportion of the total mining costs. For some wet mines the direct costs of pumping and drainage may range from 35 to 40Ø per ton of ore produced, but the indirect costs due to handling wet ore and controlling the water may be five to ten times this amount. The methods of study were formulated as the work progressed, and inasmuch as they were the first large-scale studies of their kind, they should serve as a guide for the solution of similar problems in other mining areas. The Iron River district was chosen for a pilot study because in this district the longest records of mine pumpage and water-level observations were available, including, as they do, the records for the Homer mine of the M. A. Hanna Co., where pumping from surface wells began in 1930. The results of the first investigation by the Michigan Department of Conservation have already appeared." The first section of the report on a similar study of the Marquette district, which was started in 1948, will be published this year. Methods of Study In an effort to reduce the flow of water into the mine workings in the Iron River district, about 4500 gpm was pumped from the bedrock being mined and about 9000 gpm from the glacial overburden. In the Marquette district in the vicinity of Ishpeming and Negaunee, about 5000 gprn was pumped from the bedrock and about 4000 gpm was pumped from the glacial overburden. Where the water was pumped only from the bedrock, the rate of pumping ranged from a few hundred gallons per minute in the dry mines to many hundred gallons per minute in the wet mines. In each district, pumping from the overburden was localized on a few properties where costly pumping installations had been made and the expenditures for power had been large. In each district a comprehensive ground-water investigation was made of the whole area, involving the collection and interpretation of all the available data bearing on the source and quantity of water to be controlled. Although it is not the purpose of this paper to discuss the methods of making a ground-water investigation, it should be pointed out that a drainage study follows a pattern of engineering analysis that determines the occurrence, source, movement, disposal, and quantities of water involved. The investigation in the iron-mining districts of Michigan began with the construction of a map of the buried bedrock topography. Because the ground-water reservoirs occupy the low points in the bedrock basins, this map gives information concerning their areal extent, depth, shape, and degree of interconnection. The depth to water in the drillholes and wells indicates the altitude to which the ground-water reservoirs are filled, and the logs of the material penetrated in the drillholes and wells indicate the general character of the materials filling the reservoir. The slope of the ground-water surface indicates the direction of flow through the reservoir, the water movement being from the points of higher altitude to points of lower altitude. By analysis of the rise and fall of the ground-water levels in response to additions of water through recharge and to changes in the rate of discharge through pumped wells, estimates of the total quantity of water in storage and of the rate of flow through the reservoir

Jan 1, 1952

By F. O. Jones

The capabilities of small proportions of divalent cations, such as calcium or magnesium, for controlling clay blocking are reported. Potentially sensitive formations can be exposed to fresh water if at least one-tenth of the salts dissolved in both the native water and invading fresh water are calcium and magnesium salts. Often, even less suffices. The behavior evidently depends upon the cation exchange properties of the clays, which favor adsorption of calcium and magnesium over sodium. Clays having sufficient adsorbed calcium and magnesium resist dispersion by water and consequent blocking of permeability. An allied phenomenon, the dependency of clay blocking on salinity contrast, is also reported. Abrupt change from highly saline to fresh water can cause blocking which may not occur if salinity is lowered slowly. A process related to osmosis is thought responsible for this behavior. Applications of findings to drilling, fracturing and water flooding are discussed. INTRODUCTION Many formations, when exposed to fresh water, can lose permeability through clay effects.',' For example, drilling-mud filtrate can cause oil permeability decreases, which persist long enough to interfere with drill-stem testing and well completion.3 Ultimate productivity may suffer when clay damage is severe, especially if drawdown pressures are low.' The injection pressures and the time required for water flooding can increase if clay blocking occurs. Earlier work indicates that clay blocking is caused by obstruction of flow channels by clays or other mineral fines dispersed by fresh water.'!" It is well known that increasing salt concentrations in water tends to prevent clay blocking. Also it is well established, although perhaps not as widely known, that the nature of the dissolved solids is also important. If, for instance, formation clays are exposed to calcium chloride solution and then exposed to weaker solutions of calcium chloride or distilled water, considerably less permeability damage results than if the clays had been exposed instead to sodium chloride solutions. The reasons for this behavior are: (1) clays are cation-exchange, or base-exchange, materials similar in this respect to zeolites or exchange resins, and (2) clays in the calcium form do not disperse easily in fresh water, whereas clays in the sodium form do. The base-exchange form of a clay is easily altered by flowing a solution through it. For example, a sodium clay can be changed to a calcium clay simply by passing a calcium chloride solution through the clay bed. There is general agreement that the reason calcium and magnesium clays do not disperse easily in fresh water is because the calcium ions do not ionize easily from the clay surfaces.' Sodium clays, however, are believed to allow the sodium ions to ionize from the clay particle surfaces. In fresh water, this allows the particle to accumulate a net negative electrical charge great enough for the particles to repel one another and, therefore, disperse more easily. The foregoing suggests that, even in the presence of a large excess of sodium, a relatively small ratio of divalent cation, such as calcium or magnesium, might serve to prevent clay dispersion. The divalent ion probably adsorbs to a disproportionately large extent, because of being adsorbed more tightly, with the result that the proportion of divalent cation on the exchange positions of the clay might then be great enough for the clays to resist dispersion. Consequently, an investigation was conducted to find how mixtures of salts in solution influence clay blocking. APPARATUS AND PROCEDURE Water permeability tests were conducted using conventional techniques. The equipment is illustrated schematically in Fig. 1. Flow rates of solutions driven through small core samples at known temperatures and pressures were measured. Regulated compressed air, usually at 10 to 15 psig, was used to drive the solutions. Core samples 0.75 in. in diameter and 1 in. long were used for the most part. Cores were saturated by evacuating and then admitting a de-aerated solution. Tight core samples were first saturated with carbon dioxide gas and then evacuated and saturated with the test solution. After saturation, 140 psig pressure was imposed for several hours. Cores were tested to insure absence of gas saturation by a Boyle's

Jan 1, 1965

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.D. Box 1183, Johannesburg.

By Stanley L. Lopata, Eric B. Kula

SEVERAL methods are available for determining pole figures by X-ray means.' The earlier film methods have been replaced by techniques in which the intensities are measured by Geiger counters on an X-ray diffractometerZm7. These methods utilize either flat transmission or reflection samples,214°8 cylindrical specimens,3 or spherical specimens.7 A single transmission or reflection sample will not yield information over the complete pole figure. The cylindrical specimens suggested by Nortod and the spherical specimen of Jetter and Borie7 have the advantage of allowing the whole pole figure to be obtained without any corrections to the intensity for absorption, There is a lower limit to the size of sheet which can be conveniently studied, however, and sample preparation can be rather tedious. Probably the most common method today for determining the complete pole figure is that developed by Schulz. A flat reflection sample is used for determining the pole figure from the center out to about 70". Because of the geometry of the system used, little or no correction for absorption or irradiated volume is necessary.4'6 A separate transmission sample is used for the region near the edge of the pole figure. This procedure requires two separate samples, one of which must be a thin carefully-prepared transmission sample. Furthermore, since the reflection and transmission data are in different arbitrary intensity units, a region of overlap must be obtained, and the intensity data from one set of measurements converted to units of the other. These are serious disadvantages of this method, and they point out the need for a simplified procedure. Since the reflection technique can be used for planes whose normals lie up to about 70° from the sample surface normal, it is apparent that a complete pole figure can be obtained by reflection alone if sample surfaces are cut at oblique angles to the rolling plane Specifically, if a rolled sample is cut so that the normal to the surface formed lies equidistant (54" 44') from the rolling plane normal, rolling direction, and transverse direction, then complete information for one quadrant of the pole figure can be obtained by reflection from the surface. Fig. 1 shows this oblique surface, as well as the position of the pole of this surface in the pole figure. When a surface has been cut oblique to the rolling plane, the standard polar stereographic net is inconvenient to use, and it would be more desirable to have the center of the net coincide with the pole of the oblique plane. Fig. 2 shows such a net, where the center has been offset 54' 44' to correspond to a specimen cut as in Fig. 1. This net was in effect obtained by rotating a standard polar stereographic net 54" 44' with the help of a Wulff net. With the experimental setup used. a sample can be cut from plate of 1/2-in. thickness or br Gen- erally thinner sheet is under investigation, and a composite specimen must be used. A convenient procedure has been to bond together, using epoxy resin, sufficient sheets to form a cube. These are clamped in a vise, and when dry, the whole vise is rotated and a flat surface ground at the required angle. The sample is then mounted inside a larger steel ring using Koldmount, the backside ground flat and parallel to the approximate desired thickness. The sample is then polished and etched to remove any effects of cold working during grinding. With this method only one quadrant of the pole figure is obtained. Often pole figures show symmetry around the rolling and transverse directions, and any slight asymmetry is due to scatter. Should the pole figure not be symmetrical, four oblique surfaces, corresponding to the four quadrants of the pole figure, would have to be examined. In most cases there is symmetry at least around the rolling direction, which reduces to two the number of quadrants to be investigated. For many purposes all that is required is an average polefigure for the four quadrants. This canreadilybe obtained with composite specimens of sheet material, where sheets Corresponding to each of the four quadrants can be intermixed. The four quadrants can be obtained by considering sheet in the normal position, and by rotatiolls of 180" around the sheet normal, the rolling direction, and the transverse direction. If desired, the whole thickness of the sheet can be used, yielding an average of the surface and interior textures; or the surface material can be removed from each sheet, resulting in a pole figure for the center alone. Eugene S. Meieran of the Massachusetts Institute of Technology has independently developed the same method. His results, adapted to a pole figure goniometer with a specimen spiraler, will be described in another publication.

Jan 1, 1962

Your Council has pleasure in submitting its report for the year ended 30th June, 1970. COUNCIL The following served as Office Bearers during the year under review: Messrs J. K. E. Douglas (President), V. C. Robinson and Prof D. D. Howat (Vice-Presidents), R. C. J. Goode (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Mr. R. J. Adamson, Dr. M. G. Atmore, Mr M. Barcza, Dr J. M. Bereza, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, G. W. Holl, Dr J. P. Hugo, Messrs N. A. Honnet, P. Lambooy, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Dr J. T. McIntyre, Messrs J. Meintjies, T. C. A. Meyer, J. A. Nixon, Prof R. P. Plewman, Dr R. E. Robinson, Messrs J. F. Reid, H. Simon and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of seventeen and the standing committees held 45 meetings. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R4,608 compared with R2,124 last year. This deterioration can be attributed largely to two important factors, namely an increase in secretarial fees of RI, 789 and an increase in the loss on the Journal from R2,343 to R3,508. In addition, our contribution to the expenses of the Federation of Societies of Professional Engineers increased by R607 from R549 to R1,156. The increase in secretarial fees is partly due to our increased demand for services and partly to increased salaries. In order to maintain its essential services it has been necessary for the A.S. & T.S. to increase salaries in order to keep pace with commerce and industry. With regard to the Journal, we did not expect immediate dramatic results from the changes that were effected as from the beginning of last year in the arrangements for publication. However, the improvement has been even slower in materialising than we expected. This situation is being watched carefully and we will not hesitate to make further changes if necessary. It became clear early in the year that the financial position was deteriorating and your Council decided that it was essential to meet the situation by raising subscriptions and entrance fees. At the same time it was decided that there are no grounds for a distinction between Town and Country members and that in future the scale for the compounding of subscriptions should be based on anticipated future membership, rather than past membership. These changes have had only a minor effect on the accounts under consideration. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R132 and the total fund was, therefore, increased by this amount to R4,338. The balance sheet shows that the market value of quoted shares and debentures decreased during the year from R13,059 to R6,567, while accumulated funds now amount to R17,959 compared with R22,567 last year. It will also be noted that we are holding R25,844 on behalf of the Symposium on Opencast Mining. MEMBERSHIP Twenty-eight Fellows, twenty-four Members, seventeen Graduates, twenty-five Associates and twenty-seven Students were elected during the year. Four Members were admitted to Life Membership; Five Members were transferred to the grade of Fellow; one Student was transferred to the grade of Member; two Graduates and one Student were transferred to the grade of Member; six Students were transferred to the grade of Graduate; One Associate was transferred to the grade of Fellow; One Associate was transferred to the grade of Graduate. One Fellow, one Member, six Graduates, four Affiliates and ten Students were removed from the Membership Roll in terms of by-law 7.7.1. Your Council records with deep regret the death during the year, of the following: R. A. H. Flugge-de-Smidt, C. S. McLean, Dr H. J. van Eck, (Honorary Life Fellows), J. C. Humphreys, O. Lazar (Life Fellows), D. G. Beadle, J. G. Craig, P. U. Fisher, R. G. McConnell, J. H. Moore, S. Sterling, L. R. Ulyate (Fellows), H. H. Burger, E. A C. Dickson, R. Jack, S. Ring (Members), M. J. Worrall (Graduate). A comparative statement of the membership as at 30th June, 1970, and the end of the previous year is shown in the following tabulation: 30th June 30th June Honorary Life Fellows 10 8 Honorary Fellows 6 6 Life Fellows 189 191 Fellows 514 530 Members 448 465 Graduates 68 80 Associates 155 172 Students 162 161 1,552 1,613 RECLASSIFICATION OF MEMBERSHIP The designations of grades of membership were altered to accord with the practice in professional institutes both here and overseas and members were advised of the new classifications. MEMBERSHIP DRIVE A committee was established to organise a drive for membership as it was felt that there are numbers of persons in our mining and metallurgical industries who are not yet members but who qualify for membership. Members of the committee were allocated responsibility for campaigning in sections of industry and for publicising the aims, objectives and advantages of belonging to the Institute.

By Stephen G. Mlot

Technical Study Work ?Technical study work enables informed decisions: -Obtain a higher price for a quality asset -Minimize expenditure on a project that won?t provide adequate returns -Optimize expenditure on a project to capitalize on the potential return

May 1, 2013

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin [1] were the first to develop a first-principle flotation model by considering the role of surface forces in bubble-particle interactions. According to the model, the ζ-potentials of particles constitute the energy barriers, E12, for particle (1)-bubble (2) interactions, which corroborates well with the observation that flotation recoveries reach maxima under conditions of zero-zeta potentials. In the present work, a series of surface force measurements were conducted for the quartz-dodecylamine hydrochloride (DAH) flotation system, for which detailed studies had been conducted by D.W. Fuerstenau [2], including the measurements of zeta-potentials, contact angles and collector adsorption as a function of pH.

To help mine safety and health professionals manage and reduce hazardous noise exposure with a software tool that simplifies the record-keeping and analysis process. Background Hearing loss resulting from overexposure to noise continues to be a problem throughout the U.S. mining industry. Studies indicate that 70%?90% of all miners have a noise-induced hearing loss severe enough to be classified as a hearing disability by the time they reach retirement age. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software program. DOSES is designed specifically for use by mine management and safety personnel to simplify the record-keeping and analysis associated with time-motion studies, making it easier to identify and solve noise exposure problems.

Jul 1, 2009

To reduce operator exposure to drilling noise from roof bolting machines. Background Noise-induced hearing loss (NIHL) is a prevalent occupational illness in the United States. Studies indicate that 70%?90% of miners have NIHL significant enough to be classified as a hearing disability. Mine Safety and Health Administration studies indicated that roof bolting machine operators are among those overexposed to noise. Field studies support the premise that, on average, drilling is the loudest noise source to which a roof bolting machine operator is typically exposed and contributes greatly to the operator?s noise exposure. The National Institute for Occupational Safety and Health (NIOSH) has further determined that the drill steel and chuck radiate a significant amount of noise during drilling. To address this noise hazard, NIOSH developed a collapsible drill steel enclosure (CDSE) to encapsulate the drill steel during the drilling portion of the roof bolting machine duty cycle. In addition, NIOSH is collaborating with J. H. Fletcher & Co. in the continued development of a CDSE.

Sep 1, 2008

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By Les Philips

National Institute for Safety and Health?s (NIOSH, USA) Office of Mine Safety and Mine Safety and Health (OMSHR) has definitions for: -Proximity Detection as detection of personnel, vehicles and other objects near a machine using some type of sensor technology -Proximity Warning (aka Collision Warning) as detection of personnel, vehicles and other objects near a machine resulting in alarms that ?Warn the operator only ?Warn the operator and nearby personnel (two-way) -Collision Avoidance as the processing of sensor information resulting in control signals or actions that alter machine status/movement to avoid a collision by ?Computer control ?Human control

May 1, 2013

By R C. Schodde

The future of any mining company depends on maintaining and growing its access to high-quality mineral resources. Often the true size of a given resource is not fully recognised until after mining has commenced. Also, the strong desire to increase production puts pressure to expand the resource base of the mine to get maximum value out of the capital employed. This, plus diminishing M&A opportunities and declining world-class greenfield discovery rates, makes brownfields exploration a high priority activity in any operating company. For the success and long-term survival of the company it is critical that this is done well. The primary aim of brownfields exploration is to find or acquire new deposits within economic transport distance of an existing mine that will add materially to shareholder value through: mine or capacity expansion, displacement of lower-margin ore from the mine plan, preserving and extending the mine life, and ensuring potential value is understood in order to maximise potential future mine development or exit. A number of strategic principles are important in any program designed to achieve these aims: understanding the life of mine (LOM) production profile and the related key drivers for exploration, understanding the dynamic nature of the brownfields search space, understanding and measuring depletion of the brownfields search space, understanding the potential of the near-mine region, investing in exploration technology to expand the search space, and investing in a basic geological understanding of the ore-environment. Examination of the LOM profile will highlight critical issues facing development plans for the mine including future grade and throughput issues, key technology requirements or innovations and scenarios for increased production. Exploration targets in the brownfields program should address these key issues. Often it is as æsimpleÆ as keeping mine development sufficiently far ahead of extraction to allow time for the various phases of exploration and resource assessment drilling. Because of the low additional capital costs required, expansion of the brownfields search space is strongly leveraged to: metal prices, development of new markets, incremental operating cost reductions, strategic changes in downstream requirements in integrated businesses, depletion of higher unit-value ores, and new technologies (both extraction and exploration). Therefore the brownfields search space is likely to incrementally expand through time and must be regularly reviewed. This is also important as any given search space will be progressively exhausted, resulting in smaller and higher cost discoveries. It is therefore important to monitor and critically review sustained trends of increasing brownfields discovery cost. The first wave of discoveries in any camp are usually empirically driven and do not need a strong geological understanding. However, an improved geological understanding is critical to making the next generation of hidden discoveries. To illustrate these points, a case study was carried out on the exploration and development history of the Kambalda nickel camp. Over a period of 40 years, more than 40 deposits were found containing over 1.7 million tonnes of nickel metal. Efficient mines need to maintain reserves for operating flexibility. Consequently, the company needs to clearly understand the global resource in order to maximise its full potential. In addition, understanding the full brownfields potential earlier in the development of a deposit rather than later, creates optionality through the flexibility that this understanding brings to future development choices. To ensure best practice in attaining this aim, the roles and responsibilities of the exploration team and the mine operation should be clearly understood. It is important for the explorers and the operators to have shared views about what needs to be done. Typically, mine operators would be accountable for identifying future resource requirements to support the life-of-mine production schedule whilst explorers would be accountable to ensure best-practice assessment of brownfields exploration opportunities. This would include an assessment of the global undiscovered endowment in the regional near-mine area. The balance between brownfield exploration drilling and resources to reserve conversion will need to be decided to ensure efficient operations are maintained. Both need to agree the optimum level of brownfields funding taking into account: urgency to replace or grow reserves, and quality of opportunities (relative to those elsewhere). The ultimate cost of ignoring the full brownfields potential of an operating asset can be significant, ranging from inefficient and poorly planned operations, lost opportunity cost and resultant value through under-utilised resources and, in the worst case, early exit from the asset at the bottom of the commodity cycle û leaving behind huge amounts of shareholder value.

Jan 1, 2006

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By G. L. Wilhelm

Prior to the construction of a 450 tpd concentrator at the Mayflower mine, owned by the New Park Mining Co. and operated by the Hecla Mining Co., the common mining methods were cut and fill, with waste or gob filling and square set timbering with waste fill. Stoping operations were beset with the usual problems related to waste filling methods- storage and handling of fill material from development, costly waste excavations necessary to obtain a portion of the needed waste rock, slow mining cycles due to filling and inefficient ground support. After Hecla Mining Co.'s successful utilization of sandfill in its mines in the Coeur d'Alene district, utilization of hydraulic fill in stoping operations at the Mayflower was a logical development of the modernization plan then in progress. The mine, located in the southeasterly part of the Park City mining district, Utah, is a medium size producer of lead and zinc ores, with gold, silver and copper as secondary minerals. The mine has been producing commercial ore since 1939 from a dual vein system which outcrops at an elevation of 7200 ft in the Wasatch Range. Access to the present mining areas is gained by a 7200-ft haulage tunnel and by an interior, three-compartment main shaft. The present mining horizons are about 2400 ft deep. The average horizontal cut and fill stopes, ranging from 3-15 ft wide and up to 120 ft long, can be classed as small.

Jan 5, 1968

By Jim Richard

Introduction Electric Vehicle Controllers (EVC) and the Northern Centre for Advanced Technology (NORCAT) have created two generations of Lunar Highland Simulant ?Simulant preparation techniques and equipment resulted from drilling activities in support of Regolith and Environment Science and Oxygen and Lunar Volatiles Extraction (RESOLVE ) ?The purpose of defining the compaction process was to minimize the effect of density on drill testing This allowed other variables including drill bit geometry, auger, RPM, and thrust to be evaluated independent of density ?Density of Highland Regolith falls within a range of 1.40 to 2.29 g/cm3 (p484 Lunar Source Book)

May 1, 2013

By M. M. Nash

Since the late 19th Century, scholars have been concerned about finding proper methods of managing business. The search seems to be taking us full-circle to the time and motion studies of Taylor (Horn, 1987). It wasn't until the late 1970's, however, that systematic investigations were made in the mining industry. One of the first was a study by Sanders, Patterson, and Peay (1976). That project explored the relationship of attitudes and safety. Peay, Atkin, and Goodman (1977, then reviewed the whole area of Organizational Development, including the so-called Rushton experiment.

Jan 1, 1988

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988