Search Documents

By B. Szpunar

Structural and mechanical changes of urania are investigated when oxidized to U3O8. The CASTEP ab-initio quantum mechanical program, employing density functional theory is used. The total energy technique is implemented to investigate changes in the lattice constants. The ab-initio calculations predict a 36% increase in the volume per uranium atom when transforming from UO2 to U3O8, which agrees very well with experimental data. The implication of this prediction on the linear expansion and fuel fragmentation is discussed. The calculated elastic constants of urania are in good agreement with experiment. The predicted mechanical properties of UO2 and U3O8 are compared.

Aug 1, 2010

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006

By H R. Phillips

The ventilation and refrigeration design of underground mines is an important aspect, when new or existing mines are considered and places a great responsibility on engineers tasked to do so. The current trend for both local and international underground mines is to extend their search for valuable ore reserves deeper below surface. In South Africa, the predictions are that about 40 kt of actual gold still lies in situ, ready for extraction. As mines extend their search for minerals of economic value deeper and deeper into the earthÆs crust, ventilation and refrigeration aspects of such mines become more prominent than before. The planning and design of the required ventilation and refrigeration within these mines, over their expected lifetime is important including the practical implications of such designs. Technology changes and improvements need to be incorporated into ventilation and refrigeration designs, where possible and advances in this specialised field explored. This paper explores ventilation and refrigeration design aspects within the underground mine sphere. Aspects such as mining depth, virgin rock temperature (VRT), mining methods, and different cooling applications available including ventilation supply are reviewed in design applications. Heat generally becomes a significant aspect to counter in these mines and they are not always necessarily deep mines.

Jan 1, 2005

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By R Trueman

An improved ability to predict dilution for narrow vein deposits enables more accurate economic comparisons between mechanised longhole stoping and other narrow vein mining methods, as well as reducing uncertainty surrounding dilution estimates for deposits at the prefeasibility/ feasibility stage. This paper proposes narrow vein dilution prediction and minimisation strategies for both greenfield sites and operating mines, respectively. The narrow vein dilution method (NVD method) is a tool for more accurately predicting longhole narrow vein dilution. The method is based on a new concept called benchmark stoping width. Benchmark stoping width is based on probabilistic analysis of overbreak distributions from a typical longhole narrow vein mine. The premise for the NVD method is that dilution associated with longhole stoping can be predicted using the benchmark stoping width. In addition to dilution prediction, the NVD method also includes strategies for narrow vein dilution minimisation generally, including; filling, cablebolting, stress relaxation, extraction sequencing and blast overbreak.

Jan 1, 2008

Magnetic Measurements on Auriferous Veins in Brazil. BY MARK C MA¬LAMPHY (Contribution 72-Preprint; also Trans, vol 110 4900 words) One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul Recently the Companhia Estrada de Ferro e Minas Sao Jeronymo has been making a detailed survey of the area, and the author of this paper was requested to study the possibility of applying geophysical methods. The present paper gives a few details of the work and the results obtained The problem was difficult and the results not particularly brilliant, according to the author, but the data are believed to represent another advance in the application of the magnetic method of prospecting The instrument used was a Schmidt-Lloyd vertical magnetic field balance made by Askania Werke It did not prove of value for the discovery of auriferous veins of the type there found It is believed, however, that fair results may be expected when studying the continuation of veins that disappear under alluvial covering The data thus obtained should be of exceptional value in directing the excavational work of prospecting A short appendix to the paper gives the results of magnetic observations in the Sao Jeronymo coal mine

Jan 1, 1935

By C. Barnett

"A description of the Geco orebody has been given by W .L. Brown and R.C.E. Bray (1). The mill flowsheet and equipment were described by M.J.S. Bennett, D. Wild and C. Lawton (2). Mill capacity is now 4, 150 tons per operating day of copper, silver, zinc and lead ore. A recent flowsheet has been published in the - Canadian Mining Manual (1966).Soon after the start of production in September 1957, it became apparent that large tonnages of sand would be required by the mine for backfill pruposes. Initial experimental work on the preparation of sand fill from the flotation tailings was begun in late 19 59. Cyclones of local manufacture, in a variety of sizes, were tested quite successfully. There were, however, several obvious advantages with some of the custom-built cyclones and a recommendation was obtained from the Techniquip Company. A single Krebs D-10-B cyclone was tested experimentally in 1960.INITIAL TESTWORKExperimental results showed that with our relatively coarse grind (in the order of 53 % minus 200 mesh) 75 - 80% of the flotation tailings could be recovered as backfill sand with one stage of treatment. Percolation rates of four inches per hour were obtained with cyclone inlet pressures in the range of 20 - 25 psi and feed densities of 20 - 23% solids."

Jan 1, 1968

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

Overview of Presentation Why Enter Agreements with First Nations Making it Win-Win ?The Principles The Process Making the Process Work Resource Agmts Defined Resource Agreements are legally binding agreements between a resource company and the First Nation(s) whose Aboriginal or Treaty rights may be impacted by the activities of the proposed project

May 1, 2009

By R. J. Reuss

Mina Maria is a high-grade, underground copper mine located in the Cananea district of Sonora, Mexico. The ore body is a massive sulfide breccia located in mountainous terrain. A major highway and an electric transmission line pass directly over the near-surface ore body. The mine is operated by Minera Maria SA de CV, a joint venture company that is 51 % owned by Empresas Frisco SA de CV and 49% by Cominco Resources International Ltd. Empresas Frisco is the operating partner. Production began in October 1990. The mining method used is undercut and fill. A continuous miner and a single-boom, hydraulic jumbo mine the ore. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation. The Maria deposit is located about 40 km (25 miles) south of the Sonora-Arizona border and 11km (7 miles) northwest the city of Cananea and the Cananea Mine. The mine portal, at an elevation of 1780m (5840 ft), is on the east side of an important drainage divide. The mill site is situated about 800 m (2625 ft) northwest of the mine on the northwest side of the drainage divide where the drainage is more favorable. Its elevation is 1860 m (6100 ft) (Fig. 1).

Jan 1, 1992

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By E. J. McKee

THE area discussed lies south of Canadian River in Hutchinson County, Texas, covering approximately 10 m. east and west and 4 m. north and south. Development is carried on in the manner usual in standard tool operations. No outstanding divergence from the usual methods is necessary as wells are completed in 35 to 55 days to approximately 3000 ft. Most of the time is lost in the upper part of the hole and is usually caused in driving pipe of larger sizes. After approximately 1500 ft., little trouble occurs. A comparison of 13 contractors drilling for Phillips Petroleum Co. gave the following averages: Drilling time from 32 to 63 days with a daily footage of from 49 to 87 ft. per day. The rigs furnished are National turnbuckle type with 6-in. irons and steel wheels.

Jan 11, 1926

By Harold G. Arthur

INTRODUCTION Stillwater Tunnel construction is scheduled to start in the spring of 1973. The tunnel will be the site of an extensive program in rapid excavation research. This paper presents a progress report regarding our plans and relates the tentative decisions which have been made on how to carry out the research effort. The details are subject to revision as more input is obtained from other Government agencies interested in tunnel construction and from experts in industry and educational institutions. The objective of the research program is to bring about faster, less costly tunnel construction. This objective will be pursued through the development, improvement, and evaluation of various construction systems and investigative techniques. The need for this kind of program was recognized by the National Research Council, in its authoritative report "Rapid Excavation - Significance, Needs, Opportunities." (1) The Council advocated a federally funded $200 million, 10-year program to help meet the $69 billion market it expects in underground excavation between 1970 and 1990. The significance of tunnel construction to Reclamation is made clear by statistics of its tunneling experience and outlook. Reclamation has constructed 174 water conveyance tunnels totaling over 190 miles, Six tunnels are presently under construction which have a combined length of about 27 miles. There are on the books nine authorized, but unfunded tunnel projects totaling another 70 miles in length. Many more miles of tunnels are included in programs in various stages of investigation.

Jan 1, 1997

By S McKnight, S Hall

Much of the research regarding the use of bacteria for the oxidation of sulfide minerals has been conducted using pure bacterial strains or synthetic minerals, often under ideal conditions, which does not reflect the conditions commonly encountered in commercially operating plants. This has also led to much conjecture as to the exact mechanism by which bacteria are able to enhance sulfide oxidation and as to which species of bacterial microflora are the most dominant. Recent advances in 16S rNA sequencing has confirmed that many of the bacterial species once thought to dominate commercial oxidation circuits were simply more willing to grow under the culturing conditions used and may only play a minor role in the oxidation process (Rawlings, 2002). Consequently this research will look at bacterial oxidation under conditions more reflective of commercial operations, focusing on the presence of organic carbonaceous material within a refractory sulfide orebody to be sourced from the Fosterville deposit of Perseverance Corporation Limited.

Jan 1, 2004

By R. W. Heckel, J. H. Smith, H. W. Paxton

The habit plane of proeutectoid cementute precipitated from austenite was studied using a two-trace surface (analysis coupled with a direct X-ray back-reflection determination of the orientatzon of the parent Matrix. The results were the same as those obtained by earlier workers1 - 2 who used Indirect methods to determine the orientation of the matrix. The data indicate that a range or habit planes in the parent phase is operative which is not in agreement with accepted existing theories. In 1933, Mehl, Barrett. and smith1 obtained a non-unique result in a study of the Widmanstätten habit plane of proeutectoid cementite. Their data are shown in Fig. 1. These results were verified by Greninger and Troiano,2 although they did not pre-sent any data. Both of these investigations relied upon indirect methods of determination of the matrix lattice orientation. Theoretical considerations of Widmanstatten precipitates have usually proved or assumed an orientation relationship between matrix and precipitate; the habit plane expressed relative to the matrix is generally unique, although it may be irrational.3 Opinion is divided as to the factors influencing the choice of habit plane. Mehl4 felt that a nucleus which was plate shaped to minimize strain energy and surface energy during its formation could maintain this shape by the point effect of diffusion; the

Jan 1, 1961

High precision GPS systems for mining are accurate to within a few centimetres. Typical systems consist of one or more GPS antenna, GPS boards, sensors to detect the position of the blade or bucket of the machine radios to pick up correction signals, a computer to control the system and a display screen to give instructions and information to the operator. GPS systems offer two benefits û they give information to the operator to get his job done faster and more accurately and they can send information to management about how the job was done. On dozers, GPS systems allow the operator to accurately complete earthmoving jobs with no survey pegs. On hydraulic excavators the systems can be used to accurately locate the position of the bucket teeth for selective mining. On blasthole drills the systems can guide the operator to each hole and record accurate as-drilled plans. By reporting the position of the blade or bucket in three dimensions it is possible to continuously upgrade a mapfile of the excavation. From this file it is then possible to report productivity numbers in real time. High precision GPS works best with a minimum of five satellites visible. This may be difficult in a pit. Systems which also access the Russian GLONASSS satellites offer significantly better uptime. GPS systems will become indispensable for efficient mining operations in the future.

Jan 1, 2003

By Howard K. Worner

Several features of smelting and refining operations make them appropriate technology to adapt to the processing of "wastes" not only from the minerals Industry itself, but for wastes in general. These features include significantly higher temperatures than are achieved in conventional Incinerators and also good thermal stability derived from the mass of molten metal and slag in the furnace. This paper expands on Information contributed to the Mervyn Willis Symposium in July 1992 and includes knowledge generated in the last two years of waste processing R&D in a sealed 100kg capacity DC arc furnace specially constructed for the "Environment" process being developed in Wollongong. As one product of-the process is a foundry-type iron, the feed always contained ferruginous dusts or heavily contaminated scrap. For the dusts, sewage sludge has been used as a binder and also as a proportion of the fuel-reductant. To achieve the necessary bath carburisation, It is beneficial to add other lower reactivity carbons such as "kish' graphite, carbon from electrode butts, dusts from coke ovens, carbon from aluminium pot line residues, dry cell batteries etc. Metallurgical factors involved In process control, Including metal and slag, compositions, are discussed.

Jan 1, 1994

A. 0. ASHMAN, Palmerton, Pa. (written discussion *).-From a theo¬retical point of view the best method to maintain the cold junction at a constant temperature is by means of a pipe driven in the ground, to which the so-called cold-junction compensating leads are run, ;and of course there are many times and places where it can be successfully used. There are, however, several objections to this method. In the vicinity of any furnace there are apt to be underground flues for preheated air or gases, recuperators, water mains, etc., which will eliminate the probability of a constant temperature. These, of course, can be avoided by carrying the leads to distant locations known to be free, but this is not good practice because the so-called compensating leads have a rather high re¬sistance, which materially affects the accuracy of even the high resistance instruments, unless they are specially calibrated for it. Moreover, the cost of these long leads is almost prohibitive. A better way is to run short lengths of compensating leads to electrically heated constant¬ temperature boxes conveniently located near the furnace in a place that is of fairly uniform temperature. These boxes are on the market and can be procured at a cost that is approximately equal to the cost of 100 ft. of compensating leads. They can be connected to any power or lighting circuit and once set require very little care. One box will ac¬commodate a number of couples.

Jan 12, 1919

By P. K. Guerrero, Nathaniel Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere. This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors, and more recently by Rose. This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically.

Jan 5, 1960