Search Documents

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By B G. Blacka, O Salisbury, K W. Mills, R G. Jeffrey

Whitehaven Coal Limited operates an underground longwall mine near Narrabri, New South Wales. The mining horizon in the Hoskissons Seam is overlain by a 16–20 m thick unit known as the Digby Conglomerate, a unit that is sufficiently massive to have potential to cause a windblast during first caving at the start of each longwall panel and periodic weighting throughout the panel. A program of hydraulic fracturing has been successfully used to precondition the conglomerate strata to increase its caveability at the start of each panel. This paper presents a system of temperature monitoring that was used successfully to measure hydraulic fractures at Whitehaven confirming their rate of growth, orientation and interaction with previously placed hydraulic fractures.CITATION:Mills, K W, Blacka, B G, Jeffrey, R G and Salisbury, O, 2014. Temperature monitoring of hydraulic fractures used for preconditioning massive conglomerate strata to reduce windblast, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A J. Clough

There has been an unprecedented rise in the fatality rate in the Australian mining industry over the last few years. The factors behind this rise are not clear; however, it is noted that the increase in fatalities has occurred during a fall in commodity prices.This paper examines prevention methods and systems to deal with hazards that have the potential to result in either single or multiple fatalities. Managing the risks associated with mine ventilation is used to illustrate the principals behind the approach.The paper also touches on the broad science of human error and proposes a multifaceted approach to controlling and preventing fatal risks.A summary of the steps involved in developing an effective principal hazard management plan is provided.CITATION:Clough, A J, 2015. Ensuring an effective principal hazard management plan, in Proceedings The Australian Mine Ventilation Conference, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By R C. Morris

Supergene lateritic iron ores are uncommon when compared with the vast tonnages of BIF-hosted microplaty haematite ores of the world or with the dominant supergene mimetic martite-goethite ores of the Hamersleys. In Australia and to a lesser extent in India and South America, mimetic replacement of gangue minerals by iron hydroxyoxides is a major factor in forming supergene iron ore from banded iron-formation (BIF) and results in the superb preservation of all of the original BIF features. This includes primary banding down to the finest inclusions, as a result of pseudomorphing of the BIF gangue at depth by goethite. The enrichment as a whole is an absolute accumulation of Fe at depth, dissolved from the surface BIF, and a removal of the gangue elements without loss of the original BIF mineral textures. Thus the ores grow upward to meet the downward destruction of the surface BIF by erosion. By contrast the supergene lateritic ores including the 'blue dust ores' are residual ores resulting from the relative accumulation of Fe. In the supergene lateritic ores derived from BIF, removal of the gangue is accompanied by repetitive solution and reprecipitation by secondary haematite and goethite. The final product of lateritisation of BIF and BIF-derived ores is typically complex, due to successive overprinting of earlier stages of alteration during the process, and because of the different precursors. This progressive lateritic modification tends to produce a varied surface complex including massive, vermiform, and botryoidal, or nodular aluminous/siliceous goethite and haematite, variously known as ferricrete, duricrust, canga, or 'hydrated zone hardcap'. The significant difference in these ores to the supergene mimetic martite-goethite ores is that they grow downward, with the total destruction of any of the parent BIF or BIF-ore textures.

Jan 1, 2009

By Carlos Dinis da Gama

Dada la importancia del equilibrio entre minería y la protección del medio ambiente, es necesario desarrollar una política ambiental a través de una técnica adecuada que evalué técnica-económicamente las soluciones posibles considere no solo los factores cuantificables, sino los parámetros intangibles, de difícil cuantificación, sobre los factores humano, sociocultruales, ecológicos y culturales. En esta perspectiva, el presente trabajo describe los nuevos métodos de control ambiental, donde no se legisle de modo insensato sobre los requisitos ambientales en la industria minera, y desarrolle una actitud proactiva que incluya un planeamiento y asesoría de especialistas experimentados.

Sep 13, 2001

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By Rosa Palacios, Ángel Ríos, David Velazco

Antamina es un depósito polimetálico de cobre, zinc, plata, plomo, molibdeno y oro ubicado en el departamento de Ancash, Perú, sobre 4,000 m de elevación.Se han perforado más de un millón de metros de sondajes diamantinos, habiéndose identificado 179 variedades litológicas clasificadas según los componentes mineralógicos, tamaño de grano de los granates y grado de brechamiento. Al ser el logueo geológico una actividad subjetiva, basada en la experiencia y habilidad del geólogo, fue necesario establecer un mecanismo de control de calidad del logueo geológico basado en datos objetivos con la finalidad de identificar posibles errores en dicho proceso, para lo cual se evaluó el comportamiento de las diferentes unidades litológicas en relación con las 43 leyes reportadas en los análisis geoquímicos practicados a las muestras de sondajes.

Sep 30, 2022

By Karin Bäppler

Lyon with half a million inhabitants is the third largest city in France. Urban agglomerations such as Greater Lyon demand intelligent underground solutions for the freedom of mobility of its inhabitants. The city and metropolitan area of Lyon provide an example of a city strategy adapted to the changing needs due to demographic and living standard trends. The Lyon Metro Line B with a length of 2.4 km is one of the strategic projects with regard to city planning and future mobility. The paper will highlight on this special area of application in singular diverse geology with sophisticated mechanized tunnelling technology.

Jun 13, 2021

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Leiner Novaes Arêdes

Após o bobinamento com temperatura controlada, as bobinas são resfriadas até um valor próximo da temperatura ambiente para o processo de decapagem. Há uma bibliografia farta no que diz respeito à temperatura de bobinamento e seus efeitos nas propriedades mecânicas e na microestrutura do aço plano laminado a quente. Contudo, pouco se encontra sobre a influência das taxas de resfriamento pós bobinamento nas propriedades mecânicas e na microestrutura do aço, especialmente nas propriedades finais de materiais que são submetidos à laminação a frio e recozimento. O tempo médio de resfriamento com água é de dois dias. Já o tempo para resfriamento com ar é de sete dias. Estudou-se o efeito das referidas taxas na microestrutura e nas propriedades mecânicas para um determinado aço tanto após a laminação a quente como após a laminação a frio e recozimento.

Jul 30, 2018

By Leandro Scheffer Cipriani

A microestrutura e as propriedades mecânicas de um aço de alta resistência submetido a resfriamento rápido empregando equipamentos (Roller Quench e CLC - Continuous On-Line Control), presentes na linha de laminação a quente da Usina de Ipatinga – Usiminas, foram avaliadas nesse estudo. A microestrutura obtida foi composta por bainita e ferrita, com frações desses constituintes variando em função do equipamento utilizado. Devido a essa diferença, os valores de limite de escoamento e de resistência foram maiores no aço submetido a resfriamento via CLC. O resfriamento imposto via Roller Quench propiciou ao aço uma maior tenacidade, medida pela energia absorvida em ensaio de impacto Charpy.

Oct 30, 2017

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By Nicolás Saldaña, Patricio Yanqui, Elmer Huayna

El análisis del relave minero de la compañía minera Condestable fue gestionado para su investigación con la finalidad de conocer sus posibilidades de aprovechamiento sea como materia prima, adición para un proceso, entre otras posibilidades de aprovechamiento. Para esta investigación se trabajo en la posibilidad de caracterizar el relave, demostrar que su composición es la adecuada para incluirla en los procesos que sean provechosos por su contenido de sílice, calcio, fierro entre otros.

Sep 29, 2023

By Eduardo de Oliveira Diniz

“Excelência no atendimento aos clientes” é uma máxima declarada como busca constante em todos os segmentos de mercado, inclusive no de aços longos, negócio da ArcelorMittal Monlevade. Com foco neste objetivo, muitas vezes, a empresa se volta para o mercado na tentativa de mapear as necessidades dos clientes. Após identificá-las, e absorvê-las, acaba-se criando complexidades em processos tanto em produtos quanto em serviços. A cada internalização de demanda, segue-se a rotina sob a ameaça de transformar o processo de atendimento em algo confuso e desatualizado, além de não haver segurança de que o cliente está satisfeito de fato. Este trabalho mostra o histórico recente de uma expressiva evolução do atendimento aos clientes da unidade de Monlevade, resultado obtido através de análises, utilizando a metodologia PDCA, que orientaram a uma nova estrutura da equipe de atendimento na Gerência de Logística, implicando em reformulação de acompanhamentos/controles de processos e intensificação dos contatos com pessoas envolvidas com atendimento aos clientes dentro e fora da planta. Com isso, foi possível superar, de forma consonante, a proposta da Logística Central de implantação de uma “Célula de Atendimento” em cada unidade da ArcelorMittal. Conclui-se que é necessário rever periodicamente a rotina de processos internos de modo a buscar um equilíbrio entre as necessidades dos clientes, complexidades geradas e resultado dos índices de atendimento.

Aug 16, 2017

By Flaviana Dias Rocha Pimenta

Com o objetivo de gerenciar e monitorar os recursos contrados para a movimentação interna, a VSB (Vallourec Soluções Tubulares do Brasil), implementou ao longo do ano de 2016 em parceria com a empresa DDMX, algumas soluções tecnológicas de gerenciamento da frota dos equipamentos subcontratados, atendendo as necessidades de gestão do contrato, incluindo itens de segurança e produtividade. O presente trabalho tem como objetivo apresentar o modelo de gerenciamento e sua aplicação no dia a dia da gestão, bem como os principais benefícios com a sua implantação.

Oct 30, 2017

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019