Search Documents

By Kenny Younger, John R. Morris, Scott Stonecheck

For the University of Pittsburgh's new Athletic Sports Performance Center project, a unique, technical design assist/build approach was employed to overcome both the dense urban environment and challenging subsurface conditions.  The new sports arena will house multiple venues for the university in the years to come.  With no braced floors obstructing sight lines and heavy roof loads through 65-ft tall external walls, Amelie designed an online hybrid temporary/permanent tied back soldier beam wall system over 45,000-sf of exposed face as a vertical slabs, supported on 14" wide strip footings to these 65-ft heights, thereby minimizing the cast in place outer wall thicknesses with depth.   The design also addressed surcharge effects from buildings in close proximity to the shoring system.  During construction, a significant coal mine interval was addressed as to not negatively impact the integrity of the shoring system and existing dormitory buildings.  The case history represents a one of a kind technical approach to a hybrid shoring system while sharing subsurface risk and contingency techniques to avoid potential negative outcomes.      

Oct 7, 2024

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By R Wilson, S Luke, R Williams, B Freeburn

"In 2010, two McLanahan RSS14×50 scrubber screens were installed at Fortescue Metals Group’s (Fortescue) Christmas Creek site. By 2015, the trommel (screen) section had effectively reached the end of their serviceable life. This was determined by regular measurement of structural components over the previous 18 months that tracked wear life. At the same time, numerous trials and optimisations had taken place on screen panel design and material composition. During 2015, a new set of trommels were designed, manufactured and installed that incorporated many new features: increased open area to facilitate high throughput, improved wear protection for structural members, simplified trommel panels and realigned discharge ports to reduce wear on exit. Numerous other upgrades have taken place on the drive system, feed chutes, liner and weir configurations and park brake, to name a few. This paper will highlight how regular measurement drove design changes and how the site and the original equipment manufacturer (OEM) managed a replacement program that has delivered improved performance.Citation:Wilson, R, Luke, S, Freeburn, B and Williams, R, 2016. Regular Measurement Defines Upgrades on Scrubber Screens, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By Marco Olper

The CX-EW technology, developed by B.U.S Engitec, is improved introducing besides the battery paste electrowinning, the direct electrorefining of metallic lead (grids and poles) obtained from CX breakers. This new concept of electrorefming the antimonial lead scrap is aimed to the production of 99.99 lead and of slimes with high antimony content, avoiding gaseous emissions in melting lead scrap, and expensive and pollutant thermic refining operations. In this way, practically all lead content in the battery is available as 99.99 lead, hence with a wider market for the lead recyclers. This paper will describe the tests performed on a pilot plant scale with special reference to the relatively low energy consumption of the process.

Jan 1, 1993

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

By J. LaForest, R. Riggle

In today’s challenging mining environment, everyone is focused on minimizing cost per ton. With haulage costs approaching up to 45% of the overall mining costs, and loader performance driving production, optimizing payload on the truck is a big opportunity. This paper will focus on technology’s role in loaders achieving the truck target payload. There are constantly new innovations in technology, but not everyone uses them correctly. Technology is intended to help achieve the next level of performance, but still requires the right people and processes to effectively utilize the benefits. In today’s mining business, miners, engineers, trainers, supervisors, and managers have ever increasing roles and responsibilities as never seen before in past decades. Technology can make these roles more efficient, but fully relying on the technology can detract from optimization. Sometimes the old-fashioned method of loading to a consistent pass match will provide a lower cost per ton. Before blindly trusting your technology feedback, know these three areas discussed in this paper: (1) Prerequisites to utilize technology in payload management; (2) Types of payload management technology; (3) How to use the data to manage operator behavior. The objective of this paper is to provide low-cost recommendations to efficiently increase production. INTRODUCTION Whether miners claim to have been around and experienced it all, or they are the data-driven new generation on the mine site, miners are expected to execute the mine plan at the lowest cost possible. So why is it so difficult to execute this task? Shouldn’t supervisors just have to staff the equipment, tell operators to have a safe day and tally up the numbers at the end of the shift? Let the technology system do the rest; what could go wrong? Lots. Having examined numerous mining operations that use the latest loading technologies over the past several years, one common denominator is the opportunity to improve loader operator performance. Mining companies seek help from consultants, training departments, performance reporting systems and an arsenal of resources. Armed with all this information, but the improvements don’t happen, what could have gone wrong? It comes down to people, not managing the resources to drive the right behavior and as a result, the mine’s performance is not where it should be. Understanding how to make “Great Miners” out of these people is critical to this constant struggle to move more with less and get the costs down. Extraction CPT (Cost-Per-Ton) is most sensitive to optimizing loader production which can be generalized into 3 categories of influence: machine specifications, cycle timing, and continuous management using technology. After establishing a basic production machine configuration, utilizing technology to manage cycle times, operator efficiency and payload can be advantageous. Prerequisites to Utilize Payload Management Technology It is important to begin with the primary considerations that enable the use of technology to continuously manage loading productivity. All systems are interdependent in mining, but these are divided into the simplest terms to remember. First, fix your timing and geometry.

Jan 1, 2019

By Matthew Anderson, David Day, Paul Smith

"The Midwest is presently the focus for Combined Sewer Overflow (CSO) abatement in the United States (U.S.). Most of the EPA mandated utility and municipal long term CSO abatement programs in large metro areas in the Midwest such as Cleveland, Indianapolis, Columbus, Chicago, St Louis, Akron, Fort Wayne, Louisville, Kansas City, Omaha and Pittsburg use or will use deep tunnels for storage and conveyance of CSOs. This paper will compare design methods specified and implemented for tunnel construction in Midwestern geology such as soft ground and mixed face EPBM tunnels, hard rock TBM tunnels, drill & blast tunnels, road header tunnels along with tunnel lining systems. It will also review the performance of successful CSO systems that include design life cycle, vortex and drop shaft configurations, pump stations, storage and conveyance strategies and long term operation and maintenance criteria. HISTORY and BACKGROUND Prior to development of mandated wastewater treatment plants, collecting both wastewater and storm water runoff in a single-pipe system was an efficient and economical solution. The early combined sewer systems were typically designed and sized to carry several times the average dry weather wastewater flows and not designed to handle a mixed volume of waste water and storm water during a wet weather event. Beginning in the early 1970s, federal legislation (Clean Water Act of 1972, Clean Water Act of 1977 and the Water Quality Act of 1982) changed how municipalities and industries in the U.S. were required to treat and discharge wastewater into the nation’s surface waters. They were mandated to treat wastewater at federal regulatory standards for discharge into surface waters that is safe for humans, wildlife and aquatic life. The wastewater treatment facilities that evolved were initially designed and sized to treat only the peak volume of raw wastewater flowing during dry weather. Combined sewer system control sections or relief structures were installed upstream of wastewater treatment plants (WWTP) and were designed to protect WWTPs from potential damage that would be caused if peak volumes of raw wastewater mixed with storm water runoff reached and overwhelmed the WWTPs."

Jan 1, 2016

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Yuhe Tang

High Gradient Magnetic Separator with Horizontal Magnetic Line is a new type High Gradient Magnetic Separator product. It has many specific advantages, such as water-air joint discharging technique, double pulses pulp dispersion technique, multi-magnetic gradient for collecting matrix with different diameter rods, better discharging rate with the especial matrix dispose, high separating accuracy and wide applicability. In this paper, the author makes a description of High Gradient Magnetic Separator with Horizontal Magnetic Line, and puts its emphasis on analyzing industrial production data using high gradient magnetic separator with Horizontal Magnetic Line to separate weakly magnetic minerals. It is found that as the rougher for weakly magnetic minerals separation, High Gradient Magnetic Separator with Horizontal Magnetic Line has more stable metallurgical performance and cheaper running costs than other types of High Gradient Magnetic Separator when the properties of the ore change greatly and there is in the case of embedded fine particle size distribution. Keywords: high gradient magnetic separator, self cleaning technology, horizontal magnetic line, water air discharging technique

Sep 1, 2012

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By R. E. Vivas, J. Garcia

"INTRODUCTION Freeport-McMoRan is a leading international natural resources company that operates large, long-lived, geographically diverse assets with significant proven and probable reserves of copper, gold, molybdenum, cobalt, oil and natural gas. Freeport-McMoRan is the world’s largest publicly traded copper producer and largest producer of molybdenum. The Sierrita mine is an open pit truck and shovel operation from which copper and molybdenum are produced. An important key to Sierrita’s success lies in their ability to realize their plans in the field. In certain circumstances, the mine plans are not achieved, and the operation fails to meet its targets which is an issue revealed in reconciliation reports. This technical session discusses the methodologies and procedures used at Sierrita to monitor the implementation of the mine plans, measure the performance of the operation and reduce the variance between plan and actual. Ensuring the operation stays on target is vital so mine productivity and profitability can attain its maximum potential. PROJECT OVERVIEW The Sierrita mining complex is located in Pima County, approximately 20 miles southwest of Tucson, Arizona as shown in Figure 1. The first mining claims at Sierrita date back to the late 1800s while underground mining activities started in the early 1900s. However, open pit development of Sierrita began more than 50 years ago to become the modern mining complex it is today. In 2009, Freeport-McMoRan purchased the adjacent Twin Buttes copper mine, providing significant synergies in the Sierrita minerals district. This venture included the potential for expanded mining activities, operations growth for mining copper and molybdenum, and reclamation activity. It should be noted that in addition to copper and molybdenum, the Sierrita mine produces rhenium which is a rare and highly value metal. The ore deposit contains oxide and sulfide mineralization. The oxide ore is delivered to the leach process while the sulfide ore is routed to the crusher and mill circuit 4,700 jobs on Arizona’s economy Freeport-McMoRan partners with the communities near Sierrita to provide programs that contribute to their sustainability"

Jan 1, 2015

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By E. J. Wade

The general location, climatic conditions and access of the Tasu mine are covered briefly, with comments on the Jack of conventional transportation and communication facilities. The Haïda story of Tasu and early at-tempts at production are presented, together with a discussion of the government legislation which throttled exploration and production in the late fifties. General and specific details of local geology, mineralogy and current ore reserves are also covered.

Jan 1, 1968

By Marco Aurelio Piangatelli, Massimiliano Bringiotti, Ferdinando De Angelis

"The construction of the three connecting tunnels between the east side and the west side of station C13, adjacent to the Vistula river, has a long and complex history, as they cross beneath one of Warsaw’s main road arteries (Wislostrada). After the attempt to excavate the first tunnel, the face of the tunnel collapsed on the night of August 13, 2012, and a volume of about 10,000 cubic meters of liquid mass (water, silty soil and sand) entered and flooded the west side of the station, which was filled with more than seven meters of material. Fortunately, the workers managed to escape, but machines and equipment were lost. This is the story of how the tunnels were completed, by adopting soil improvement, jet grouting, GRP bars, ground freezing and a careful choice of work steps. INTRODUCTION The Centrum Nauki Kopernik station on Line II of the Warsaw Underground is located alongside to the Vistula river (Figure 1). This station hereinafter is referred to as station C13.The station consist of three parts: the east and west part, and three connecting tunnels 40 meters in length with a large cross section (170 m2).. It includes the rails along the sides and the platform along the centre. The reason for the underground connection of two shafts with a tunnel is due to the presence of a road tunnel (Wislostrada, hereinafter called WS), which must be underpassed by the new metro line (Figure 2).The existing tunnel (Wislostrada) was built many years before, between diaphragm walls, and some foundation structures interfere with the underground tunnel. The challenge was to build the connectors without stopping the traffic of vehicles along the highway above. All works took place in very difficult geological and groundwater conditions due to the presence of Vistula alluvial deposits with poor mechanical characteristics. The soil profile consists of relatively loose sands on top, and silts overlying high plasticity Pliocene clays highly disturbed by the effects of the repeated over-sliding of glacial moraine deposits."

Jan 1, 2016