Search Documents

By Elmer Weber, W. M. Baldwin

Solid lead obeys a single parabolic weight increase vs. time law. In contrast, liquid lead undergoes three successive parabolic weight increases vs. time laws, the first of which has a low constant relative to the latter two. The conversion times for the change from one parabola to the next decrease with increasing temperature. IN recent reports on the subject,1,2 it was noted that zirconium and titanium scale in air by a complex mechanism. The scale first forming on the metal is protective to the extent that it gives a low constant, K, for Tammann's, and Pilling and Bedworth's parabolic equation: w² = Kt [1] relating weight increase, w, due to chemical reaction of the metal with the air, and time, t. After hundreds of hours of apparent stability in some cases the first scale yields to another that offers little protection to the metal. This transition from one scale to another, from a slow parabolic oxidation reaction to a fast one, was not due to impurities in the atmosphere or incidental effects (changing environment, etc.) but was a specific behavior of the metal itself, the transition occurring at definite times (dependent on temperature) and showing other reproducible traits. In view of this behavior how can long-time service behavior be predicted from short-time laboratory tests, not only in the case of these metals, but in any case? Certainly a systematic study of the type of scaling behavior described above—wherever it is found—would help to answer this question. The present paper is a report on the behavior as it is found in lead—the only metal to the authors' knowledge for which the behavior has been described at all, if inadequately, for our present purpose.* At least four oxides of lead are known, of which one occurs in two allotropic forms. They are ß (red) tetragonal PbO stable up to 486°C;8 a (yellow) orthorhombic PbO stable from 486°C up to its dissociation temperature in air at about 2300°C;9 minium or Pb3O4 which from the dissociation pressure data given in Fig. 1 decomposes to PbO at 540°C in air; lead sesquioxide or Pb2O3,; and lead dioxide or PbO2 which, according to Fig. 1, decomposes in air at 400°C to minium. In view of the high dissociation temperature of PbO, lead will scale up to at least its boiling point. Further, it is known that oxygen is almost insoluble in liquid lead.'V his implies a fair probability that an oxide scale would not dissolve in the molten metal and would afford the same protection to lead in the liquid state as in the solid. All of the oxides of lead for which specific gravity data are available are more voluminous than an equivalent weight of metal or a lower oxide from which they might form, hence the scales will be in compression. Lead oxides are known to be ductile, so it would be anticipated that they would form coherent nonporous scales. It is not surprising to learn, then, that both solid and liquid lead scale according to the Tammann, and Pilling and Bed-worth law.14,15 (Gruhl states that at 600°C and above lead oxidizes linearly with time because of "spitting" of the scale.) The parabolic constants K reported by various investigators3,14-16 are badly scattered, however, as shown in Fig. 2. The oxides formed on solid lead were described as being reddish-brown but were not chemically identified by Pilling and Bedworth.15 Gruhl's descripdin³ of the appearance of the scales On his liquid samples indicates that a (yellow orthorhombic) PbO is formed initially on the specimens but gives Way eventually—at least at temperatures below 486 °C— to .ß (red tetraunal) PbO, and that below 540°C minium—Pb3O4 :is firmed at an even later time as an overlay on either the red or yellow PbO. Fig. 3 is a graphical interpretation of Gruhl's description. Gruhl does not indicate any change in the parabolic scaling rate as yellow PbO converts to red. He does indicate that minium reduces the scaling rate, al-

Jan 1, 1953

By Wm. R. Dotson

Forty years ago the atom was split and the Age of Fission dawned. Uranium was the element used in this earth-shaking accomplishment. Thitherto almost unknown to the man in the street, uranium soon became widely and persistently sought. And the quest for this unique material is not likely to diminish during this century. To find is one thing; to own is another. Who owns uranium in the ground? Where no mineral rights in the land have been severed by devise, grant, reservation or lease, the uranium belongs to the fee simple owner of the land. But where there has been a conveyance or reservation of all or part of the "minerals", determining WHAT a substance is has been the traditional way of determining WHO owns it. What, then, is this element called uranium? The 1907 edition of Watts Dictionary of Chemistry calls it "a lustrous, hard, silver-white metal". Of nature's three prime divisions it falls within the embrace of the mineral kingdom - substances neither animal nor vegetable. In its natural state uranium always is combined with other elements or substances in the form of an ore mineral. May we, then, put to rest any doubt or question as to the nature of uranium and classify it for all purposes, including that of ownership, as mineral? Not quite! That self-same logic would find oil and gas primly ensconced in the animal or vegetable kingdom. Technically, oil and gas are not minerals but legally they have been classified as such. Why? The Supreme Court of Tennessee sought the answer in 1897 in the case of Murray v. Allard, 43 S.W. 355. After citing authorities pro and con, and while admitting their origin to be "decomposition of marine or vegetable organises" that court firmly concluded that since they were obtained by a form of mining, oil and gas were minerals. From the above example two elementary truths emerge. First, for purposes of ownership, uranium is and will be whatever the courts say it is. Secondly, the courts historically and currently favor a practical rather than technical test to determine the "mineral" character of a substance. So now we turn to the jurisprudence for enlightenment and definition. EARLY CASES ALLOT URANIUM TO MINERAL OWNERS Two early cases involving the ownership of uranium followed what had been well-settled mineral within the meaning of the conveyances involved, confirming ownership in the mineral owners. In 1956 the U. S. District Court for New Mexico in the case of New Mexico and Arizona Land Company v. Elkins, 137 F. Supp. 767, appeal dism'd 239 F.2d 645 (10th Cir. 1956), found that a 1946 deed reservation of "all oil, gas and minerals underlying or appurtenant to said lands" included uranium and thorium. The court reasoned that uranium and thorium, being minerals within the scientific, geological and practical meaning of the term, would certainly constitute minerals within the purview of the reservation. While agreeing that uranium and thorium were "minerals", defendants argued that at the tine of execution of the conveyance it could not have been the intention of the parties to reserve them because they had no commercial value in the locality and were, in fact, not known to there exist until their later discovery in 1950. The court re¬jected, as a matter of law, this "lack of knowledge" theory citing the Supreme Court of Kentucky holding in Maynard v. McHenry, 113 S.W. 2d 13, that: "The mere fact that a particular mineral has not been discovered in the vicinity of the land conveyed or is unknown at the time the deed is executed rules of construction and held that uranium was a does not alter the rule . . ." that a grant or exception of "mineral" in a deed includes all mineral substances which can be taken from the land unless restrictive language is used indicating that the parties contemplated something less general than all substances legally cognizable as minerals. Further, argued the defendants, the only feasible mining procedure for such substances was open pit or strip mining, which would destroy the value of the land for grazing or agriculture. Finding that the language of the reservation was clear and unambiguous, the court would not permit the admission of extrinsic evidence as to mining procedures required. Elkins is the first uranium case construing the granting clause involved. In 1958 the Texas Court of Civil Appeals at San Antonio, in Cain v. Neuman, 316 S.W. 2d 915, no writ, held that a 1918 lease conveying "all of the oil, gas, coal and other minerals in and under" the land involved covered uranium. The lease provided a royalty of 1/10th on "other minerals." "We find no Texas precedent which discusses uranium," said the court, "but the usual arguments that uranium is not embraced within a lease are that the ejusden generis rule excludes uranium from the meaning of the lease

Jan 1, 1979

By E. A. Slover

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors

Jan 1, 1954

By Tae-kyeong Yeu

KIOST has developed the pilot mining robot, named MineRo ?? from early-2011 to mid- 2012. The robot consists of two unit-modules having an identical mechanical structure and hydraulic system. One unit-module has two track systems, two pick-up devices, two crushers, one lifting pump and one thruster. The pick-up device is fitted on the frame of the track device. All actuators are driven hydraulically, which are manipulated by valves and the controllers. Each unit-module is equipped with one dual HPU of 250kW / 4,000V. PWM-16 (INNOVA AS) as hydraulic valve controller is adopted, which outputs PWM signals of 16 channels and can be used under pressure in oil-filled box. To measure angular velocity or displacement of hydraulic actuator, turbine-type flow-meters are adopted. The flow-meter has RF (Radio Frequency) type pulse detector, which extends the flow range by eliminating drag on the rotor. Two track motors, two crusher motors, lifting pump, one thruster can be controlled their velocities through feedback of the measured flow-rates. As well as the flow-rates, the states of the hydraulic system such as hydraulic pressures, temperatures, leakages are measured through a self-developed flow-pressure canister. In that canister, multi-channel amplifier boards are installed, through which the vast amount of data is acquired and transmitted to the main controller using serial communication.

Sep 14, 2011

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads. Activity in the Eureka mining district began in the early 1870's. The oxidized high grade lead-sil-ver-gold ore terminated against the footwall of the Ruby Hill fault, and in 1890 the main operations ceased. In 1938 Eureka Corp. Ltd. discovered ore in the hanging wall of the fault by diamond drilling. The history of Eureka in the late 1800's indicates that there was some water at 600 to 800 ft in the old workings, probably accumulations above the water table which did not seriously interfere with mining operations. Both the Locan and Richmond shafts were sunk to a level below the table, but apparently the only serious difficulty with water occurred in the Locan. The steam pump used when the last work was done on the 1200 level in 1923, many years after exhaustion of the main orebodies, is still installed on the Locan 900 level. The capacity was about 500 gpm, lifting 750 ft to the 100 level, which connected with the surface. In addition to this. bailers were used to keep the 1200 level free of water. It is said that pumping in 1923 lowered the water in the Holly shaft, about a mile and a half away, but this seems doubtful. The pumping was of short duration because no ore was found. When work at the new Fad shaft was started in 1941 Eureka Corp. Ltd. engineers were fully aware of the probability of encountering water in large volume. Their primary exploration and development had to be carried on at the 2250 level. The first water was encountered at 300 ft. This was undoubtedly surface drainage in the bedding of the Pogonip limestone and was less than 100 gpm. The fractured, loose Hamburg dolomite at the water table was not well cemented, and relatively little water, 300 gpm, percolated through it with difficulty. At 1350 ft well-cemented dolomite containing some open fractures was encountered. These fractures produced the first water of consequence, 750 gpm. At 1700 ft the volume was 1000 gpm increasing to the maximum during shaft sinking, 1600 gpm, at the 2000 level. Secret Canyon shale, a dry formation, was entered at 2100 ft, where a concrete water ring was placed to catch all of the water. The volume decreased rapidly to a constant flow of 1200 gpm. Below 2100 ft the shaft and stations remained in the shale and water was not a problem. Several faults of moderate displacement, including the reverse Martin fault, had been intersected during the traversing of 1000 ft of wet Hamburg, but no undue quantities of water were encountered. Observations in the diamond drill holes in the ore zone area showed a rapid lowering of the water table. The shaft was flooded when it left the dry shale and entered the water-bearing Eldorado dolomite on the 2250 level, crossing a fissure which paralleled the Martin fault. High pressure water doubled the volume then being pumped. Pipe failure through a water door bulkhead was a contributing factor. Immediately following this flooding in March 1948 preparations were made to recover the shaft as rapidly as possible by increasing power and pump capacities as needed. Measurements before flooding indicated the water could be lowered at a fast rate. However, the water table did not recede as rapidly as expected and volumes required to lower the water in the shaft were higher. Obviously the size of the main water channel on the 2250 level was increasing because of erosion, allowing greater volumes to enter the workings and draining beyond the cone originally being drained during shaft sinking. Eroded material was being deposited in the shaft below the 2250 level in serious proportions. In December 1948 a second flooding of the Fad shaft was allowed for the purpose of reassessing existing conditions and studying alternate methods of attack. The detailed geology of the Eureka mining district, see Fig. 1, has been described during the past 75 years by many geologists.' Only the general features and those which seem to affect the drainage problem will be discussed. The old ore zone, mined between 1870 and 1890, is located in a wedge-shaped block of Eldorado dolomite between the footwall of the Ruby Hill fault and the underlying Prospect Mountain quartzite, see Fig. 2. Production of high grade oxidized lead ore containing high values in gold and silver has been variously estimated at $50 to $90 million. The tonnage mined was probably close to 1,500,000, nearly all of which was found above the water table. The new ore, discovered by diamond drilling in the hanging wall of the Ruby Hill fault, is a flat-

Jan 1, 1954

By M. Ravindran

The Government of India started its deep seabed exploration programme during 1982. This programme was started as one of national importance and several national laboratories were involved to realize the development of requisite technologies for deepsea mining and processing. After a concentrated effort on surveying, using its own as well as hired ships, India succeeded by mid 1980s in identifying a prospective site in the Indian Ocean as an exclusive claim for development. India was registered as a Pioneer Investor and became the first country to obtain this status on 17th August 1987. India has been allocated an exclusive mine site of 150,000 km2 in the Central Indian Ocean. Our country also developed considerable expertise in the metallurgical processing for extracting metals from these nodules. The Department of Ocean Development, Government of India, the organization which is designated as the nodal agency responsible for implementing the deep seabed mining programme has drawn up a long term plan which will enable it to fulfill its obligations as a Pioneer Investor. The work toward the design and development of a mining system has been entrusted to the Central Mechanical and Engineering Research Institute, Durgapur. As a part of this programme they have developed a nodule collector and a riser system which have been tested in very shallow waters only. Since this technology development for deep sea mining applications is highly time consuming and very expensive, this programme is also being used to develop components for intermediate applications. In view of the long timeframe required for perfecting a deepsea nodule mining technology, the Government of India is also keen on developing shallow water mining systems for utilizing the placer deposits. One of the richest heavy mineral deposits in the Indian Exclusive Economic Zone is available on the west coast of South India in the state of Kerala. The coastal stretch between Kanyakumari, on the southern tip of India, and Alleppey along the west coast at a distance from the tip of approximately 210 km, there is a good multimineral reserve. The initial survey indicates that the estimated reserves in the surveyed areas are approximately as follows: Ilmenite 1.4 million tonnes Rutile 0.14 million tomes Zircon 0.13 million tomes Sillimanite 0.53 million tonnes

Jan 1, 1994

By Walter Voglauer

On May 14, 2011 a chimney blast took place in Vienna, Austria. The blasting operation was part of the demolition works at a former railway fabrication. The demolition works on this ground were done under the leadership of the Austrian construction and demolition company PORR. In agreement with the civil organizations which were involved, the commander of the Regional Military Command of Vienna, Brigadier general Dr. Karl SCHMIDSEDER ordered a reserve force engineer company to demolish the chimney. The concrete planning of the chimney blasting was done by specialist Markus SEWALD who belongs to the HEERESTRUPPENSCHULE (combined armed force school) of the Austrian armed forces.

Jan 1, 2013

By S. Jeffress Williams

Continental shelf margins are dynamic sedimentary environments that contain important benthic habitats and support many functions such as navigation, national defense, cables, pipelines, trawling, and oil and gas and mineral extraction. Coastal margins also contain resources such as sand and gravel aggregates, which are becoming increasingly important for beach nourishment to mitigate coastal erosion and enhance recreation and to restore degraded coastal ecosystems. Existing geologic maps of the seafloor and sub-bottom sedimentary character, morphology, texture, composition, and other seafloor properties are not available for some regions, are out of date and not inclusive of the massive data collected during the past several decades, and are not in GIS-based digital formats. New geologic maps, based on unified and integrated national digital datasets, showing the sedimentary character of continental margins are critical tools for both research to better understanding the geologic history and processes of continental margins as well as the distribution of habitats and resources and for managing coastal-marine resources. The majority of existing seafloor maps are decades old and do not include recent data from mapping surveys, seabed sampling and observation carried out by federal agencies, universities and industry. Because continental margins are increasingly important, comprehensive and integrated databases are needed to produce GIS-based digital maps displaying information such as seafloor geology, sediment character, texture and distribution. To meet the need for a unified database of seafloor sedimentary character, the USGS is conducting the Marine Aggregate Resources and Processes project, a national assessment of marine sand and gravel with federal, state, and academic partners.

Jan 1, 2004

By B. A. Ferguson, P. W. MacMillan

INTRODUCTION Jack Spalding in Deep Mining, Chapter 3, states: "In deep mining, to start stoping an orebody without a definite plan of operations covering the whole extraction from beginning to end is to invite serious trouble. Any stoping without plan is bound to leave, toward the end, a number of pillars, remnants, or promontories, which, as they are reduced in size, are liable to fail and cause a general collapse. The object of stope planning is so to mine an orebody that at no stage in the operation is a remnant left. Definition: `When a block of ore is stoped in such a way that eventually a small piece is left entirely surrounded by stoping, that piece is termed an island remnant.' The design of and adherence to a plan of stoping is of greater importance in preventing rock bursts than the type of ground control adopted." This, of course, is just an example of the old axiom that an ounce of prevention is worth a pound of cure. And in this context, mining does not have to be very deep before poor ground conditions, made worse by lack of good planning, force a mining company to resort to more expensive methods of ore recovery. At all times when rock pressures become excessive, stoping plans must be devised to avoid the creation of pillars or promontories. This is most readily recognized when mining deep narrow ore veins by open methods. It would be a little more general to say that stoping systems should seek to avoid or minimize localized concentrations of rock stress. Ore bodies, and particularly those at Falcon¬bridge, can reach large widths and leaving pillars for extraction at a later time cannot be avoided. However, good planning can reduce the effect of factors which create bad ground conditions. The necessary ingredients of planning are time and information: time to formulate and revise ideas; information, gained in exploration and early development, to provide the fullest knowledge of the ore body. In this way, plans become meaningful. It must always be kept in mind that the long-term results of good planning often require decisions not compatible with reaching earliest full production. PLANNING FOR DEEP MINING At Falconbridge Nickel Mines ore bodies presently being found and prepared for production lie at depths in excess of 610 m (2000 ft) below surface. Current un¬derground exploration is being directed towards favor¬able locations below 914.4 and 1219.2-m (3000 and 4000-ft) depths, at most mines. The Onaping Deep ore body has been traced to a depth of 1508.8 m (4950 ft) and at Falconbridge mine the ore body is under develop¬ment below the 5000 level. Planning for more efficient ground control has therefore become an important con¬sideration of future mining. HYDRAULIC BACK FILLING AND CUT-AND-FILL STOPING The advent of hydraulic back filling has led to the increasing use of flat-back cut-and-fill stoping methods during the last ten years, until it has probably become the commonest method of mining deep ore deposits in Canada. These methods account for almost all the pro¬duction from Falconbridge Mines at this time. The ad¬vantages claimed are: safety-a minimum of open ground; very little supplementary ground support (except rockbolted backs and walls); greater selectivity and flexibility in extraction (horizontal extension of the vein, high grade ore stringers going out into the walls); and high productivity and increased mechanization in larger ore widths. There is some difference of opinion as to whether hydraulic classified tailing back fill provides any great resistance to initial closure of the stope walls. The evi¬dence available suggests that it does not. Addition of portland cement to the back fill just prior to placement has produced a material having the properties of a weak concrete. It is confidently expected that this material will assist greatly in the efficient mining of pillars and generally in giving increased ground support to oppose closure. PRINCIPLES OF STOPE PLANNING BY LONGITUDINAL FLAT-BACK CUT-AND-FILL Again quoting from Spalding: "The practice of con¬trolling output by stopping and starting stopes is bad¬stopes once started should proceed without interruption, and control must therefore be obtained by altering the rate of stoping. It is therefore necessary that faces should normally advance at a medium rate which can be boosted, if required, to give temporarily a greater output. Modern high productivity stoping methods, however, generally aim to achieve and maintain the maximum output possible from a stope. Control of tonnage and grade, therefore, becomes a more complex problem requiring very careful scheduling and organiza¬tion. With the basic method of flat-back overhand stoping using hydraulic fill, it is not usually possible to mine in such a way as to avoid creating pillars." Consider an ore body as illustrated in Fig. 1. It is 274.3 m (900 ft) high by 228.6 m (750 ft) long on strike and averages 4.6 m (15 ft) in ore width. It rep¬resents approximately 907 000 t (1,000,000 st). The ore body could be mined by advancing one long single face through all the levels from bottom to top. A total face length of 228.6 m (750 ft) would accommo¬date five 45.7-m (150-ft) stopes. See Fig. la. Each of these stopes would produce approximately 1814 t/m (2000 stpm) and the ore body would require a period of ten years for complete extraction. A possible im¬provement to this scheme might be to stagger the indi¬vidual stope faces. See Fig. 1b. Problems of hanging wall failure can be reduced by this arrangement. From the point of view of reducing travelway maintenance, it is good practice to employ a stoping system of retreat. Stopes farthest from the shaft are mined first so that on completion, haulage drifts below can be aban

Jan 1, 1982

Operationalizing the Ruggie Framework in a Mining Context Ruggie?s 3 Pillars: The State?s duty to Protect Policies, regulation, adjudication The Corporation?s responsibility to respect Acting with due diligence to avoid infringing Addressing adverse impacts when involved in abuses Access to Remedy ??even the most concerted efforts cannot prevent all abuse.?

May 1, 2013

By Carlos Andrade

An engineering endeavor involves the creation of an expansive, environmentally conscious reinforced sloped MSE wall system. The objective is to enlarge a flat mining work area. Situated in southern Arizona, this mine is dedicated to extracting essential resources such as Manganese, zinc, silver, and lead, crucial for advancing clean and renewable energy initiatives. The project necessitates the implementation of a Mechanically Stabilized Earth retention system. This system aims to both expand the mine’s working area and facilitate access to underground tunnels. The expansion pad must be robust enough to endure the substantial loads exerted by heavy mining machinery. The wall’s reinforcement components are strategically designed to counteract the challenges posed by aggressive soil conditions with low resistivity. Furthermore, they must be resilient against potential damage during installation. The system’s ease of transportation is crucial due to challenging access conditions, and its design must allow for efficient drainage. A significant consideration is the integration of a face system that fosters vegetation growth and seamlessly merges with the existing flora of the area. In addition, plans include the construction of an access road downslope from the wall. The chosen solution involves a reinforced sloped system with a 70-degree incline. The wall’s surface is adorned with an erosion control mat, intended to promote the proliferation of vegetation. For added durability, the wire basket units are equipped with galvanized wire featuring a polymer coating. High tensile strip bonded geogrids, featuring a robust polyester core, provide essential reinforcement. The completed wall is an impressive feat, spanning 1500 feet in length and soaring to a height of 45 feet. It stands as a testament to innovative engineering in harmony with environmental and functional considerations.

Feb 1, 2024

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984

By Brooke Clements

The Buffalo Head Hills region is located approximately 350 kilometres northwest of the city of Edmonton in northcentral Alberta (Figure 1). The Alberta diamond joint venture consisting of Ashton Mining of Canada Inc., Alberta Energy Company Ltd and Pure Gold Minerals Inc. began exploring for kimberlites in the Buffalo Head Hills region in late 1996. At the time, the Mountain Lake diatreme, located 200 kilometres to the southwest, was the only reported kimberlitic rock in Alberta (Leckie et al., 1997, Figure 1). Exploration efforts since 1996 have successfully identified a new diamondiferous kimberlite province in Canada.

May 1, 2001

By G. G. Marino

Little comprehensive information has been reported on the behavior of room-and-pillar mines. The objective of this paper is to present case data on mine failures in the Illinois basin for use in practice. Presented are results of an ongoing study and details on the site characteristics of cases where sags have developed on the surface. Site data are reported to show the geologic, mining, and sag conditions that existed. Sags mainly develop from pillar, floor, or pillar-floor failure. The character of the sags depends upon the type of mine failure as well as the overburden response.

Jan 1, 1989

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Jr. Stokowski

Topsoil for revegetation projects is in demand in many urban areas. In this case history, a large aggregate producer manufactured a topsoil from three waste materials. The topsoil was produced in a 200,000 m2 (50-acre) abandoned gravel pit that still had additional gravel under 10 m (30 ft) of overburden uneconomic to strip directly. The topsoil was produced by rotary mixing of sludge, overburden, and a lime admixture; solar drying; and stripping and stockpiling of the product. A major problem was an increase of topsoil drying times for stripping from 40 to over 100 hours when it was rewet by storms. The problem was solved by a research project that evaluated over 50 formulations and over 20 waste materials. . The final formula dried in 15 hours and contained 3-parts sandy mine spoil, 1-part sewage sludge, and 2 % spent-bed, a granular quick-lime produced during power-plant flue-gas desulfurization.

Jan 1, 1988

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By Andrew Salach

Experimento laboratorial avalia desgaste em rodas e trilhos de PR’s. Chegou-se a conclusão de que rodas com elevada dureza economizam desgaste de rodas e de trilhos.

Aug 16, 2017