Search Documents

By J. E. Schiller, S. E. Khalafalla

To improve technology for treating process water, US Bureau of Mines research has shown that magnesium oxide (MgO) has many advantages over lime or caustic soda for precipitating heavy metals. Sludge produced by MgO occupies only 0.2-0.3 times as much volume as the precipitate made wing a soluble base. While a settled, lime-formed precipitate is easily resuspended, the MgO-metal hydroxide sludge becomes cemented together on standing. Settling of the metal hydroxides from a dilute suspension is more complete than precipitates formed with other bases. Virtually any metal that can be precipitated by raising the pH can be treated using MgO. A three fold to fourfold stoichiometric excess of solid reagent is added. The mixture is reacted for five to 10 minutes. Polymer is added, and settling or filtration completes the process. Because of the greater cost of MgO compared with lime, large-scale practice of this technology will probably be limited to water containing 50 mg/L (3 gr per gal) or less of dissolved metals. For such dilute solutions, chemicals are not a large fraction of total treatment costs, so more desirable sludge properties might justify higher chemical expenses. While the MgO process is technically suitable for widespread application, the extent to which it is adopted will probably be determined by a trade-off between the greater cost of MgO compared with lime and the superior properties of the precipitates and their corresponding ultimate disposal costs.

Jan 1, 1985

Under date of Sept. 30, the following open letter was addressed to the Members of the Colorado Section of the American Institute of Min-ing and Metallurgical Engineers by a Colorado Committee: At a meeting of the Colorado Section of the American Institute of Mining and Metallurgical Engineers, held on Friday, Sept. 19, a reso-lution was unanimously passed condemning the Engineers' Licensing Bill passed at the last session of the State Legislature, and requesting the Chairman to appoint a Committee to act in conjunction with the other National Engineering Societies and the Colorado Metal Mining Associa-tion, with a view to securing its repeal at the extra session of the Legis-lature which the Governor has expressed his intention of calling. It may be within your knowledge that the bill in question was passed by the Legislature and signed by the Governor without the knowledge of any of the National Societies, and of few if any of their members. Under its provisions residents of other states cannot even come into this to examine a mine without securing a license, and aliens (among whom are many honored members of, the profession in Colorado) cannot obtain such a license at all. The mining industry in this state needs the coopera-tion of outside engineers, and we should welcome any assistance from them that will tend to develop our resources. To attempt to discourage the activity of visiting engineers will inevitably react on us, and brand the state as being hostile to brains and capital from outside. The difficulty of securing a license will prove a serious handicap to young engineers starting out in the independent practice of their profession. Moreover, a license issued to au engineer qualified in one branch will entitle him to practice in any other: so that the license is apt to mislead the public.

Jan 11, 1919

By R. F. Shurtz

This note calls attention to a contradiction in current eatistical theory and to corresponding difficulties in practice. These are significant concern in evaluating almost all ore deposits. The theoretical contradiction is that the commonly used spherical model for the semivariogram is not consistent with the usual definition of a "regionalized variable" as a mathematical function, the direct study of which "is excluded because its spatial variability is usually extremely erratic, with all kinds of discontinuities. . ." (Journel and Huijbregts, 1978). Specifically, this means a grade function that is too "rough" for interpolation to be useful. The practical difficulty is that the spherical semivariogram interprets the data upon which it is based in a manner that is, more often than not, demonstrably inconsistent with reality. This is attributable to the widely disregarded interaction between the sample pattern and the grade function. Each sample pattern "blurs" the grade function in its own particular way. It is as though the grade structure of the deposit were seen through a lens of poor resolution or reflected in a warped mirror, such as those found in amusement parks. The fitted spherical model embeds this sometimes dangerously blurred and distorted image in the Krige regression. A full analysis of these inconsistencies is to be presented later but, in the meantime, it seems urgent to communicate their effects so that those engaged in estimating ore reserves may be on guard. The spherical semivariogram has a sill and can be replaced by the corresponding covariogram. The equation of the spherical covariogram in normalized form, that is, variance and range both equal to one, is represented as: [ ]

Jan 1, 1984

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By E. F. Bailey, L. S. Birks

The effect of stress on the austenite to ferrite transformation in carbon steel was studied by X-ray diffraction techniques. Tensile stress was found to cause reorienta-tion of austenite above the transformation temperature, to accelerate equilibrium conditions at the transformation temperature, and to cause precipitation of large carbides at a critical value of stress. IN the past, a number of papers' have discussed the effect of stress on the austenite to martensite transformation at relatively low temperatures. In general, it has been shown that tensile stress induces some transformation at a given temperature, while compressive stress retards the transformation. Very little work has been reported on the effect of stress on the transformation from austenite to ferrite plus carbide near the A, point in steel. One of the few papers in the literature2 reports an increase in A1 of about 1°C in pearlitic steel upon the application of tensile stress. In this paper, the effect of tensile stress on eutec-toid steel at, and above, the A, point was studied in

Jan 1, 1956

By Geraldine Rosenthal, Gadi Yohan, Roman Benram

Description of Project: Tamar Group’s civil division was awarded a contract to implode the Sun Hotel, an abandoned 14-story building located along Bat Yam’s coastline, roughly two kilometers south of Tel Aviv, Israel. On Nov. 6, 2012, Tamar Group’s experts positioned explosives in strategic locations of the building, targeting its central pillars, which then caused the building to collapse within seconds. Tamar Group used a relatively small amount of explosives in order to generate a well-controlled blast. This is the largest scale demolition carried out in Israel to date.

Jan 1, 2014

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.' Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

By Mark S. Stagg, Michael J. Nutting, Douglas R. Barlet

Single-row bench blasts at a reduced scale in the field were used to study the effects of delay time on fragmentation. Nine shots with a spacing of 21 in. and a burden of 15 in. (S/B = 1.4) and nine shots with a spacing of 30 in. and a burden of 15 in. (S/B = 2.0) were completely screened to determine particle size distributions. Delay intervals between holes ranged from 0 to 45 msec, corresponding to effective delay intervals ranging from 0 to 36 msec per foot of burden. Each shot was instrumented with strain and pressure gages to measure in situ blast dynamics and to evaluate interactions between blastholes. Finer overall fragmentation was produced for shots with delay intervals between 1 and 17 msec per foot of burden. Only for shots within this optimum delay range was it observed that the strains induced by stress waves constructively interacted with strains induced by gas pres- sure from an earlier detonated hole. Coarsest fragmentation resulted at delay intervals less than 1 msec/ft, where stress waves from each hole were observed to interact destructively, and at delay intervals greater than 24 msec/ft, where no inter- action between holes was observed, indicating a condition that can be considered as the firing of single hole shots independently.

Jan 1, 1986

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By M. H. Moys

A method of estimating the percent solids in the discharge from a grinding mill is described and tested on both pilot and industrial scale. It involves the use of energy and mass balances around the mill discharge sump, requiring measurements of the flowrate and density from the sump together with temperatures of all streams flowing to and from the sump. Accurate estimates of the dynamic variation of mill discharge percent solids are made available, provided that occasional manual sampling of the stream is done to cope with drift in instrumentation. The use of a computer in this application was essential; the various advantages associated with its use are discussed. It is anticipated that this estimate of discharge density can be controlled at a set point by manipulation of the water fed to the mill, resulting in significant decreases in specific power consumption and media consumption.

Jan 1, 1987

By F. L. Wolf

THE reclaiming of metallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections, the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby most of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, and table. PRELIMINARY TREATMENT The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five molding floors per day; and the last is collected around the sprue cutters. and knockout bench.

Jan 9, 1920

By H. A. Schwartz

By analyzing cementite separated electrolytically from white cast iron of known composition and history, the distribution of silicon between austenite and cementite during and after freezing has been followed. The results constitute a contribution to our knowledge of equilibria in the ternary (metastable) system iron-carbon-silicon. Incidental information was obtained, also, with respect to the distribution of manganese, silicon, and phosphorus, when only relatively small amounts of each are present. The major conclusion of the paper is that during solidification, equilibrium is attained when the silicon is all rejected to the liquid phase, permitting silicon-free austenite to separate. OF THE outstanding investigators of the system iron-carbon-silicon, Gontermann,1 Charpy and Cornu-Thenard,2 and Honda,3 only the first touched on the chemical composition of the solid and liquid phases in equilibrium with one another. He concluded that his data did not permit a decision as to which of an indefinitely large number of pairs of compositions of liquid and solid would be found in any given case. If through the three dimensional equilibrium diagram of the iron-carbon-silicon system an isothermal plane is passed in the region of partial solidification, two lines of intersection with the liquidus and solidus, respectively, are obtained, also a point marking the alloys' composition. If, in this, plane, a straight line is drawn through the point, and intersecting both the liquidus and solidus isothermals, the two intersections mark a liquid and a solid alloy that may be chemically in equilibrium at the chosen temperature. From thermal data alone, Gontermann could not assign any particular direction to the line and, hence, could not determine which pair of conjugate points to choose.

Jan 7, 1924

By Linkson PB

The presence of residual cyanide in mine tailings and fill sands may, under specific circumstances, lead to acute and/or chronic cyanide poisoning of the environment and individuals. In this paper, the nature of cyanide contained in mine tailings is discussed, along with the circumstances under which such cyanide would become a hazard. A number of methods for cyanide degradation are reviewed in the paper, with special emphasis being placed on biological degradation (due to its low costs and the non toxic nature of the degradation process itself). Recommendations are made as to the best methods of setting up a biological degradation system, for use in mining Situations.

Jan 1, 1987

During the course of an investigation into the fundamental chemistry of the cyanide process, it became evident that the usual method of determining protective alkalinity was not completely satisfactory. T.he routine method for the determination of protective alkali by first removing free cyanide by the addition of silver nitrate, followed by titration of alkali with dilute acid using. phenolphthalein as indicator, can be shown to give correct results only when the alkali is a strong base. For other sUbstances, the alkali so determined is not the protective alkali. In view of the complications associated with the presence of zinc in cyanide solutions the discussion will be restricted in the first place to solutions free from zinc. Until the chemistry of simple cyanide solutions is placed on a quantitative basis it will be difficult to elucidate the behaviour of complex mill solutions.By the use of physico-chemical theory, it is possible to treat certain aspects of 'the chemistry of cyanide solutions in a manner which not only illustrates the important variables involved, but which also shows the need for care in interpretIng results obtained by conventional methods.In the following, comparatively simple systems are discussed; the principles established should be of use in interpreting the behaviour of more complex solutions. The methods described are not intended for routine work, but may be regarded as supplementary to the usual analysis carried out for the control of plant solutions, or as alternatives to be used when the latter do not appear to be satisfactory.

Jan 1, 1948

By Harrison A. Schmitt

One of the great copper-producing areas of the world is comprised of five U. S. western states and northern Sonora, Mexico. The Southwest province of this area, covering southern Arizona, south- western New Mexico, and northern Sonora, produces some 55 pct of U. S. copper output and the equivalent of 15 pct of world production. In 1956 the area produced about 550,000 tons. Tucson is approximately the center of the oval- shaped province, which measures only 300 miles on its east-west axis and about 200 miles on its short axis. Northwest of the oval, and forming a tenuous connection with the Utah and Nevada copper fields, is an important operating mine, Bagdad, and also the now inactive United Verde. Along its north- south axis, running from Globe, through Tucson, to Nogales, ten moderate to major copper properties have been discovered or revived during the past 15 years, and five of these in only the past seven years. The latter five properties lie in an area 25 miles in diameter, centering 20 miles south of Tucson. In order of discovery, or revival, they are: Banner's Mineral Hill and Daisy; Cyprus et al's Pima; Duval's Esperanza; Asarco's East Pima (now called Mission mine) ; and Lewisohn's Peach. Total tonnage is estimated at about 250 million tons averaging some 0.90 pct Cu, but ultimate production may exceed this amount since some of the reserve is open ended.

Jan 6, 1959

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By E. S. Bardwell

DURING the period extending from May, 1922, to September, 1923, the copper-refining furnaces of the Great Falls Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont., were operated exclusively with pulverized coal as fuel. The installation was made first as an experiment. It proved successful from the start and was abandoned solely because fuel oil from the Sunburst field became available at a price sufficiently low to make its use desirable from an economic standpoint. The equipment required for pulverized coal has, however, been kept intact and is available for immediate use should the oil supply fail. Inasmuch as pulverized coal had been used on two large reverberatory smelting furnaces and was, at the time we were considering its application to the copper-refining furnaces, being used on the Wedge furnaces roasting zinc concentrate for the electrolytic zinc plant, we were equipped with a coal-pulverizing plant of ample capacity to supply pulverized coal for the furnace refinery. The only problem was to devise suitable means for transporting pulverized coal from the pulverizer plant, located in the smelter building, to the refinery about 1000 ft. distant and about 150 ft. above the level of the pulverizer plant. When studying this installation, it should be borne in mind that the layout represents an adaptation suited to the existing conditions at this particular plant. The installation was entirely satisfactory and uniformly dependable but might be modified to advantage from an operating point of view if an entirely new installation were being planned.

Jan 9, 1925

By H. H. Campbell

In the extending employment of open-hearth steel for structural purposes, it is a matter of prime importance that the test-piece shall represent with practical accuracy the characteristics of every portion of the heat from which it comes. In ordinary practice this homogeneity is assumed; but inasmuch as leading exponents of the revolving-hearth system have claimed that a reasonable uniformity could be obtained by their method alone, it may be pertinent to offer a few facts on the subject. The following heats made by the Pennsylvania Steel Company, for bridge-work, were tested by casting two four-inch ingots, one being taken during the first third and the other during the last third of the cast. Test-pieces obtained from these small ingots usually give results inferior to those obtained from larger sizes; but for purposes of cornparison they are equally conclusive. Many of the tests were made for experimental purposes within a few hours of the time of rolling, and before sufficient time had elapsed for the usual molecular redistribution necessary for the best results. All the tests were made on 3/4-inch rounds just as they left the rolls and without annealing; the results, therefore, are subject to the errors caused by variations in the diameter, and in the temperature at which the bar was finished. The tests from any one heat, however, were always nude as nearly as possible under the same conditions; and inasmuch as these data include the results of every heat so tested, and inasmuch as the errors could not by any chance always support any single theory, we may be certain that the unanimons testimony of the experiments indicates a valid conclusion.

Jan 1, 1886

The Library of -the above-named Societies is open from 9 A.M. to 10 P.M. on all week-clays, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library; either by purchase or personal solicitation as, gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 11, 1914