Search Documents

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

By R. E. Allen

One of the most unusual oil-field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fé Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from the vertical as possible and that crooked holes with elbows and dog legs were to be avoided because of the drilling and producing difficulties encountered therein, but that many nonvertical holes were slanting or angling rather than crooked and were not a serious problem.

Jan 1, 1934

By Robert B. Parsons

"Canada doesn't really have a tax system for mining - it has eleven separate tax systems! The consequent maze adds some undefinable margin of difficulty to making investment decisions in Canada. But, this 11U1Ze is not likely to be simplified. Solution: learn it and sell it! Intricate Network of Winding PathwaysWebster's New World Dictionary defines the word ""maze"" as follows: ""a confusing, intricate network of winding pathways; labyrinth ... a state of confusion or bewilderment"". Webster's does not go on to give an example of a maze, but the dictionary could easily have referred to the taxation of a Canadian mining operation. The uninitiated would almost certainly look upon such taxation as a maze of the most perplexing sort.Twenty years ago, Canada's tax system was really quite simple. It is true that Canadian mining profits were subject to three levels of taxation (federal income tax, provincial income tax, and provincial mining tax), but this didn't pose a problem. Prior to 1974, at least the provincial income tax systems were somewhat the same in terms of rules .and rates, and even the provincial mining tax systems resembled one another. Mining profits were subject to pretty much the same rules, no matter what province or territory hosted the mine. Those were the “good old days” one could even dare to generalize about tax rates without fear of being labelled an imbecile!"

Jan 1, 1994

By Edward H. Williams

In the middle of the eighteenth century John Frazier and wife, Sarah Ingraham, removed from Boston, Mass., to Philadelphia, Pa., where he was held in such esteem that we find him one of the Committee which arranged the ball at Washington's inauguration. Their son, John Nalbro Frazier, was prosperous in his mercantile career and fortunate in his wife, Anne West, who was an important personage in the early life of Professor Frazier. This cultured lady brought into the family an atmosphere of religious enthusiasm, of thoroughness and of unity of purpose. Her son, Benjamin West Frazier, inherited her traits and displayed them during a short and active life. Like his father, he engaged in mercantile pursuits, and was a member of the firm of Zimmerman, Frazier & Co. In their interests he lived for a short time in Montevideo, and on

Jan 1, 1906

By Steven Johnson

The regulatory landscape has changed considerably since the first passage of Oklahoma's land-reclamation requirements in 1968 (Open Cut Reclamation Act of 1968). The Oklahoma Legislature revised the reclamation requirements in 1971 with passage of the Mining Lands Reclamation Act. With the passage of this Act, the Legislature empowered the Oklahoma Department of Mines with jurisdiction for permitting and regulatory authority over non-coal (industrial-minerals) mining operations. This act required all operators to file with the State, through the Department of Mines, a written application for a permit to engage in non-coal mining. Each application consisted of a mining plan, which included location maps of the proposed mining area along with a reclamation plan for the area to be covered. Additionally, a reclamation bond is required prior to issuance of a permit to ensure that the site would be reclaimed. Since 1971, the Act has been amended to include public notification and public participation in the review process of any application. Also, the operator can request that the Department review the mining plan based on the Life Expectancy of the mine, instead of the original one-year plan (HB 1409 in 1993). Even though the operator is granted a mining plan tied to the "Life Expectancy" of the site, the permit is reviewed annually for compliance as required by law.

Jan 1, 1999

By J. C. Irvine

Meramec Mining Co., a joint venture of Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property is located near Sullivan, Miss., about 113 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the ore body was mineable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production began in April 1964. The ore body is overlain by about 400 m (1300 ft) of flat-bedded sediments. It is tabular, about 800 m (2600 ft) long and up to 180 m (1600 ft) thick. It dips about 80° and is of unknown depth. The ore is mainly high-grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry.

Jan 9, 1976

W. Morton Webb, Germiston, Transvaal, South Africa (communication to the Secretary*):—The experience of Mr. Boeh-mer in the Leadville district and his reputation as an engineer assure the interest of anything he may write on the ore-bodies of that district; and all engineers who have operated in Leadville will agree that the theory of the origin of the Leadville deposits, as given by Mr. Emmons in his famous monograph, does not adequately explain the genesis of all the deposits. The solutiou of the problem does not, however, appear to be quite so simple as Mr. Boehmer would make it; and the advance pamphlet issued by the U. S. Geological Survey, pending the completion of the main report, shows that there is still much ground for controversy. No doubt the later eruptive0 had a greater influence on the deposition of the ore-bodies than was thought at the time of the first investigation by the Survey; but it has always appeared to me that the influence exerted by these dikes mas more in the nature of a physical than a chemical one. The weight of evidence in recent years is mostly in the direction of ascension rather than lateral secretion; and one of the strongest evidences is the fact that most of the ore-bodies lie under one of the comparatively impervious layers which help to make up the structure of these hills.

Jan 1, 1911

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By Wang Youlai

Sichuan province is the richest province for its waterpower resource in China, perfectly suited to develop a high consuming energy industry. Sichuan Aostar Group Company has two Aluminum smelters, Guangyuan Aostar smelter and Sichuan Aostar Smelter. The production capacity of Aostar Group was 240,000 tons in 2004. The construction scale of Sichuan Aostar Aluminum smelter is 250,000 tons per year. The first 168 GY-300KA pre-baked anode cells (125,000 tons/year) were put into production in 2003. This company has taken the lead in the use of the transfer gantry technology in China. Besides making the process of calibration the pot shell it has concentrated the efforts to construct cell lining elsewhere. This company also has taken the lead in China for using the EIRICH force mixing and cooling technology as well as in the world for the CP Company?s vertical ball mill technology that produces the pre-baked anodes. The carbon anode system completed its 190,000 tons/year production scale. This is the most advanced technology and the biggest scale pre-baking anode manufacture in China. Since the Sichuan Aostar 300KA cell was put into production, it runs normally and smoothly. Up to now the current efficiency is higher than 94% and the specific energy is only 13300kWh/T-Al.

Jan 1, 2006

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process.

Jul 1, 1956

By G. K. N. S. Subasinghe

An attempt has been made to explain the behavior of a pinched sluice in terms of the established theories of fluid mechanics and mineral processing. A method has been developed to calculate the underflow discharge by assuming a logarithmic velocity distribution and free gravity fall through the discharge slot. The concentration profile of solids over the depth of flow has been shown to comply with Bagnold's theory of dispersive shear, rather than turbulent sediment transfer. Even although the results can be explained qualitatively by the Bagnold theory, their complete quantitative analysis will not be possible until more work is done. Consequently, an empirical equation has been developed to predict underflow pulp densities. It has been shown that the process of the segregation of the heavier mineral beneath the lighter can be described by a first order law. From the results obtained, a computer model of the pinched sluice has been developed. This predicts the underflow grade, pulp density and flow rate in terms of the feed and operating conditions. The model can also be used to determine the effect of a change in operating conditions, and for the optimization of rougher, cleaner, and scavenger circuits.

Jan 1, 1984

By Keith Contor

The concept of using simulators to train operators of vehicles is not new. However, the Bureau of Mines initiated these programs to determine if computer controlled training devices would enhance production and improve safety in the coal mining industry. Two prototype devices have been constructed, tested and are currently operational. The continuous miner and dragline operator training systems both incorporate full scale operator stations using operational controls and displays. The operator interacts with the visual system through the cab controls to perform basic tasks and develop skills required for startup, operation and shutdown of the mining equipment. Data pertaining to the concepts and techniques applied during the design, development and evaluation of the training devices are presented. Descriptions of trainer designs and visual systems for training equipment are presented and the results of the system evaluation are summarized.

Jan 1, 1983

By Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dis-sociated in the liquid state, as indicated by the continuous for in of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a =6.52, b = 8.60, c = 4.16 A.2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb From the known free energies of formation of CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

Launching the Queensland Water Plan 2005 - 2010 in August 2005, Premier Peter Beattie compared the stateÆs water resources with liquid gold. QueenslandÆs peak industry body for the minerals and energy sector, the Queensland Resources Council (QRC), believes the analogy is appropriate. During early development of an industry water strategy, it has become apparent that water is like liquid gold, in that it is revered, hoarded, recycled, priced on purity, a magnet for speculators, both difficult and expensive to transport effectively, heavily regulated and fundamentally linked to issues of security. To date it has generally been economic and relatively straightforward for the resources sector to secure water. Although production has not been compromised, this must not be grounds for complacency as there is every indication that water will continue to become increasingly expensive, more tightly regulated and, relative to a growing demand for a finite water supply, increasingly scarce. During 2006, QRC has developed and is implementing a voluntary industry water strategy to address a range of challenges confronting the resource sectorÆs security of access to water. As a consequence of, at times, protracted community consultations over QueenslandÆs catchment-based water planning processes it has become clear that many community stakeholders have outdated perceptions of the stateÆs resources sector. Once established, QRCÆs water strategy will incorporate a community engagement campaign to present the industryÆs credentials as a leader in water resource management. The development of QRCÆs water strategy, and the challenges the strategy is designed to address, provides insight into the fundamental reforms that are occurring in how water is managed and regulated in Queensland. These reforms have implications for how government policies are designed and administered and also for how industry engages with communities during this transition process.

Jan 1, 2006

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By William Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to tem-perature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts.

Jan 1, 1935

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954