Search Documents

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on milling and metallurgical subjects; to determine the existence of mining maps, arid to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1916

The seventies was a decade of intensive hydrometallurgical activity, firstly for copper recovery, then uranium, and finally gold. In comminution, semi-autogenous grinding was applied to uranium and gold ores. In leaching there were extensive investigations into pressure and in-situ systems, and into ammonia and chloride leaching processes. Solvent extraction became a major unit operation for copper recovery. New reagents and equipment were introduced. There was a resurgence of ion exchange for uranium as low grade sources were tapped and continuous ion exchange systems developed. Carbon-in-pulp technology came to the fore for gold recovery with the development of desorption and electrowinning systems. Electrowinning was widely applied for copper in conjunction with solvent extraction. There was a continued move to greater mechanisation and higher current density. There were important developments in solid-liquid separation such as high capacity thickeners, belt filters and sand filters. Many of these trends will continue in the eighties. Interesting new developments can be expected.

Jan 1, 1981

By N. E. Grosvenor

The study of rock mechanics is becoming more important each year and several groups are currently engaged in the study of rock mechanics instrumentation and techniques that can be used to determine rock properties in place. As it becomes necessary to mine lower grade ores, larger equipment and tonnages are required, which in turn call for larger openings underground. In addition, rock mechanics studies are necessary for designing large underground openings for defense and powerhouses, and highway and water tunnels. Meramec Mining Co. has a rock mechanics program in which they are trying to develop a means of detecting ground instability prior to failure. In one case advance warning resulted in valuable lead time for back filling stopes before pillar failure had progressed to a dangerous extent.1

Jan 2, 1968

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

By Luis A. Fierino, M. Ashraf Mahtab

This paper reviews the background of, and solution techniques for, the major geomechanics problems affecting caving operations, including prediction of cavability, defining size distribution of or fragments, stability and support of production openings, and control of rock bursts and subsidence. Further research is also suggested in the solution of the various geomechanics problems.

Jan 1, 1984

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976

By Oscar Ccaccya Anca

Se viene realizando monitoreo de condición a las Zarandas Vibratoria en Chancado Secundario y Terciario, para lo cual se aplica diferentes técnicas de Análisis, entre las cuales está la técnica de Vibración, que, gracias a una serie de configuración respectiva y filtros del valor adquirido, puede apreciarse el deterioro progresivo para su pronta intervención.

Sep 1, 2017

By N. Mao

This paper presents the results of a research effort to develop a technique for estimating in situ stresses by measuring stress-induced velocity anisotropy around a borehole. Relevant parameters required to make the estimate were identified and measured in the laboratory on a 35.6 cm (14.0 in) cube of Nugget sandstone with a 10.2 cm (4.0 in) diameter hole, under biaxial loading. Two pairs each of radially and tangentially polarized transducers were placed inside the hole with displacement directions either parallel or perpendicular to the principal stress directions. With this configuration, relative travel times were measured by both a pulsed phaselocked loop technique and a cross correlation of digitized waveforms. The biaxial velocity data were used to back-calculate the applied stress. The standard deviation of the differences between the calculated and applied stresses is 0.62 MPa (90 psi) for a stress level up to 8.63 MPa (1250 psi).

Jan 1, 1984

The gold deposits of Kalgoorlie are the most important on the Precambrian shield of Australia. Gold was first discovered.'-:.V. ,,.,.-,..Kalgoorlie in June, 1893, and olthough`the original find was of ;:...;;small extent, the prospecting activity which stemmed from it 'led to'the ciscovery.of the lodes of the Golden Mile, some three miles to the south. Th¬ production of thea1algoorlie fiold.a.t December 31st, 1962 was 80,556,572 tons -for -33.,853, 215 ounces of gold. Most of this production has come from the Golden Mile area anu Table 1 summarises the Gplueh Mile. production for periods which correspond approximately to the main phases of operation of the field.

Jan 1, 1964

Regulation of the Coal Industry. BY HOWARD N EAVENSON (Tech Pub 711, also Trans, vol 119 3400 words) A review of conditions in the bituminous coal industry during the last 15 years and of the attempts to remedy them through Appa¬lachian Coals, Inc, and through the NRA The lack of any provision in the so-called "Guffey" law for conservation of our coal supplies is pointed out and the efforts at regulation of the English coal industry are described Assuming that some regulation of the industry is necessary to maintain reasonable working and living conditions and that Federal control by compulsion will not be possible, the requirements for regulation

Jan 1, 1937

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By J. A. C. Diering

All underground openings are three-dimensional, and in many cases it is not valid to analyse two-dimensional sections. This has been a problem in the past owing to the magnitude and complexity of three-dimensional stress analysis. In this paper a three-dimensional boundary element approach, using non-conforming quadratic elements, which is specifically applicable to underground excavations, is described. In addition, the philosophy of application of stress analyses is discussed. Three case histories are presented to demonstrate the practical nature of the approach as a tool in solving mining problems.

Jan 1, 1987

ICI Australia has been developing PC-based software to assist the blast engineer to design and monitor open pit blasts. The scope of this software differs significantly from commercially available mine design packages.The software is designed for routine use in a normal production environment. The system enables the engineer to produce practical documents which include: a drilling plan, a loading sheet, a hook-up diagram, an inventory of explosives and auxiliary items, and other data on the blast such as tonnages and powder factors.

Jan 1, 1992

By J. C. Smock

The primitive mode of mining clay by open workings, in which the overlying beds of earth (commonly termed the " bearing ") were removed, and the clay then dug out by sinking shallow pits, is still the prevalent and almost universal mode of extraction. This is particularly true of our cretaceous and tertiary clays, which are generally earthy in character, and but slightly covered by drift and alluvium. The most accessible beds in many of our clay districts have been worked out, and clay miners are compelled to search for new outcrops, or to remove thicker beds of top dirt or bearing. Under this stimulus subterranean working, or mining proper, has been suggested. A brief notice of this new mode, as employed by Mr. Otto Ernst, near the head of Chesquake's Creek, three miles south of South Amboy, New Jersey, is here presented for your consideration. Previous to mining, the old mode of extraction, digging pits, was found to be too expensive, in' consequence of the heavy amount of top dirt and the excessively large amount of water in these overly

By Jennifer P. Harrell, D. Joseph Hagerty

In many areas of the eastern United States, especially in the Midwest, past mining activities have left large and extensive underground openings. Now, renewed mining is occurring in such areas in surface pits. Also, construction blasting often occurs in rock over such old openings. Within the last fifteen years, some attention has been given to the interaction between surface blasting and underground cavities; concern has been expressed about the possible changes in vibrations transmitted through areas underlain by old mine workings (Siskind, Stachura and Nutting 1987). Previous studies also had indicated that underground openings could influence transmission of surface mine blast vibrations (see, for example, Woodward-Clyde Consultants 1977). The principal concern is that underground openings under surface blasting may intensify low-frequency vibrations. If such intensification occurs, use of available equations to predict peak particle velocities and to design blasting patterns and select blasting parameters could lead to possibly damaging ground shaking.

Jan 1, 2002

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By J. W. Merks

"The accuracy of a measurement on minerals and ores can be assured by applying suitable and unbiased procedures but its precision is a function of the number of primary increments and their mass, the number of lots per consignment or samples per shift, and the number of measurements on analysis fine samples.Experimental data will be used to show how the variance components for sampling, sample preparation and analysis contribute to the total variance on which precision statements for the final measurement are based. This type of experiment should not only form part of quality control programs at mines and smelters, but also underly the criteria on which the design of manual sampling regimes and mechanical sampling systems for bulk solids and slurries should be based.Sampling systems and regimes can only be adjusted and optimized if the variance component for each step in a quality evaluation process is measured. Knowledge of precision characteristics lies at the core of effective loss prevention and control programs."

Jan 1, 1985

By Nathalie Gauthier

Bien que le système de ventilation du Puits Penna soit de taille imposante et que plus de $30M y seront engloutis pour son développement, aucun budget spécifique n?avait été préalablement consenti pour refroidir l?air acheminé aux places de travail dans la partie profonde de la mine. Le système de ventilation a été conçu en deux étapes distinctes : le réseau du haut de la mine lequel dessert jusqu?à 1550 m de profondeur et le réseau du bas de la mine (de 1550 m à 2200m) qui a été créé ultérieurement. Le réseau inférieur a été imaginé de façon à acheminer l?air frais directement au gisement et de permettre l?évacuation aux extrémités afin de rejeter l?air chaud immédiatement après l?avoir utilisé. Au total, lorsque le réseau de ventilation sera complété, plus de 670 m3/s d?air sera véhiculé dont jusqu?à 495 m3/s pour la partie inférieure de la mine considérant une capacité totale maximum de 710 m3/s en utilisant la mine adjacente.

May 1, 2003