Search Documents

By Shanti Arangala

Several improvements were made to the single strand rod mill at Laverton to increase production, reduce maintenance and improve several aspects of product quality. With changes to the water cooling line and control system, cobbles could be significantly reduced, more consistent properties obtained and yield improved. An upgrade of the laying head enabled vibrations to be reduced and thus allowed for higher speeds on small sizes. With potential for dramatically increased pipe life, a new pipe support and laying pipe system provided for improved laying pattern on small sizes and thus more uniform cooling on the conveyor and better coil package. This paper discusses details of these equipment and control system upgrades and the resulting benefits that have been realized from the project.

Aug 16, 2017

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By Cheng Yan, Yugang Li, Qian Wang, Lizhi Zhang

In continuous casting process, mold powder has lots of metallurgical effects, such as covering the molten steel to prevent liquid steel from oxidation by air, preserving heat for top layer liquid steel, lubricating initial shell and so on. However, mold powder also can deteriorate the quality of final products obviously after the entrapment of mold powder in steel. In the present work, based on the similarity theory the effect of technological parameters on mold powder entrainment was investigated by water model. Experiment was carried out in the water mold using oil and water to simulate slag and steel, respectively. The results showed that increasing casting speed increased the water-oil interfacial fluctuation and entrainment frequency; viscosity of oil also had a great impact on the interface fluctuation and entrainment; water-oil interfacial tension effect the entrainment while not changing the interfacial fluctuation; submergence depth had little impact on entrainment and interfacial fluctuation.

Jan 1, 2015

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By J. MCGUIRE, E. J. Haas, B. Demich

Near misses can enhance awareness of the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, the value of these reports and how they influence subsequent actions or controls to reduce on-the-job risks are unclear. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. The analysis provides insight into ways that risk-communication and management programs can be improved to reengage workers and their situational awareness on the job.

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By Xun Zhang, Huiqing Tang

The inner shape of a blast furnace is of fundamental importance for blast furnace ironmaking to achieve goals of high yield, high quality, low fuel rate and long campaign life. Therefore, it is worthwhile to design better furnace inner shapes. This paper conducted numerical simulations of performance for the blast furnaces with conventional and modified inner shapes. By comparing the calculation results of the two blast furnaces with the same operation conditions, it can be found that there are some certain differences. It is necessary to optimize the inner shape of blast furnace considering the results of simulations. This paper provides references for future blast furnace inner shape design and related technology developments.

Mar 1, 2017

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge A. Soares Tenório

Mining of nickel ores generates large volumes of waste that must be removed in order to eliminate water contamination and reduce environmental impacts created by waste barriers. In this context, the need for innovations concerning the recovery of magnesium present in the liquor produced by the leaching of nickel laterite with sulfuric acid arises. Therefore, this work aims to develop a study regarding the crystallization of magnesium from a synthetic liquor solution using a batch autoclave system at high temperature. Agitation speed was kept constant at 1000 rpm throughout the 3 h of batch reaction for temperatures of 230 and 200 °C. Aliquots taken at each hour were analyzed by ion chromatography to measure magnesium concentration. The highest magnesium removal was observed for temperature 230 °C. X-ray diffraction (XRD) and scanning electron microscopy (EDS-SEM) analysis proved that the product formed was magnesium sulphate monohydrate crystals. Thermogravimetric analysis coupled with a mass spectrometer was used for the evaluation of the thermal stability of magnesium sulphate monohydrate. It was found that MgO and SO2 were formed by the decomposition of the salt at 1100 °C.

Mar 1, 2017

By M. Tanaka, Y. Sato, H. Narita, S. Alam, T. Ogata

To ensure a stable supply of rare earth elements (REEs), it is highly necessary to establish the corresponding recycling technologies for RE magnets and phosphors in inplant wastes and endoflife products. Solvent extraction using 2ethylhexylphosphonic acid mono2ethylhexyl ester (EHPNA) is often applied in the separation and purification of REEs. In this study, the equilibrium distribution ratios of neodymium and dysprosium between 1 mol/L nitrate solution and the EHPNA in an alkane diluent were measured at 298K. The experimental data were analyzed by correcting the nonideal behavior of the organic phase using the Alstad empirical equation under the assumption that a complex with a molar ratio of 1:6 (REE:extractant monomer) was formed. The model correlated well with the experimental data and the extraction equilibrium constants were obtained. The extractant equilibrium constants obtained by this methodology would be useful in the design of REE recycling processes using solvent extraction.

Jan 1, 2014

By A. K. Smith

Overexposure to noise remains a widespread, serious health hazard in the U.S. mining industry. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. U.S. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine (CMM) is first among all equipment, accounting for 35% of noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a "JOY Designed for Noise Reduction" (JOY DNR; patent pending) tail section as a noise control for reducing the noise overexposures of CMM operators. Underground testing shows a 45% to 65% noise exposure reduction for the operator when comparing the JOY DNR tail section results to those for a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide CMM operators an opportunity to be within the MSHA permissible exposure limit (MSHA-PEL). Mining Engineering, 2011, Vol. 63, No. 7, pp. 83-85. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015