Search Documents

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By P Lukic

The definition of the working sections that will be used in a mine is usually initially made in the field by the geologist supervising the drilling program. These initial definitions are often made on the basis of rules of thumb such as æcoal less than 30 cm thick cannot be mined separatelyÆ; æpartings more than 30 cm thick will be mined separatelyÆ; and æif a coal seam is less than 50 cm thick and the parting above or below is thicker than the coal, the coal will be wastedÆ. These decisions are also often made based on the requirement for a minimum sample mass for analysis, and the desire to collect data at the minimum resolution to conserve the exploration budget.In many cases the geological models based on this data are produced at a resolution that is inadequate to allow the mining engineer to produce a mine plan that will maximise project value. This problem is generally unrecognised.Where data is collected to a higher level of resolution the subsequent processes employed in the production of geological models and mine plans often discards the inherent value that is hidden in this data. Again this problem is generally unrecognised.This paper highlights this problem and then presents a methodology that ensures that the optimal working section is selected and compares the outcomes of applying this methodology versus adherence to the usual rules of thumb.

Sep 26, 2011

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Thiago Félix dos Santos

A maioria dos materiais poliméricos sintéticos apresentam superfícies quimicamente inertes, isentas de porosidade e baixa energia de superfície. Este trabalho tem como objetivo realizar a modificação superficial do substrato têxtil de forma a aumentar a sua molhabilidade. Os tecidos de poliéster são hidrofóbicos e, por isso são desconfortáveis aos usuários, pois a fibra não absorve o suor do corpo, outro fator que é prejudicado pela hidrofobicidade da fibra de poliéster é o tingimento das mesmas. Portanto, tratamentos superficiais vêm sendo utilizados para minimizar esse problema e o plasma é uma técnica que se mostra bastante eficaz. O plasma ao interagir com a superfície do substrato provoca alterações químicas e físicas melhorando suas propriedades. Portanto, através do plasma é possível alterar as propriedades físico-químicas das superfícies de tecidos de poliéster, tendo como resultado o aumento da hidrofilidade dos mesmos com o incremento de grupos funcionais polares e o aumento da rugosidade em sua superfície. As amostras foram tratadas em um reator de plasma de barreira dielétrica a pressão atmosférica, em diferentes tempos de tratamento e voltagem. Após as funcionalizações as amostras foram submetidas ao teste de capilaridade, a fim de observar a melhora na hidrofilidade. Todas as amostras tratadas tiveram aumento na molhabilidade, com exceção, as amostras tratadas com 10 kV, onde não houve alteração.

Aug 7, 2018

By Vitor Guarnier Domiciano

A necessidade de melhorar as propriedades dos refratários monolíticos para resistir às condições operacionais cada vez mais severas e instáveis das casas de corrida de Alto-Forno tem sido um grande desafio para os fornecedores de refratários de maneira a garantir a segurança dos canais de corrida e sua disponibilidade para operação. Este trabalho apresenta as propriedades de novos concretos refratários Al2O3-SiC-C (aplicados por vibração ou bombeamento/projeção a úmido) desenvolvidos para resistir ao severo mecanismo de corrosão que ocorre na linha de gusa de canais principais e que exige constante atenção dos operadores das casas de corrida. Testes realizados com os novos concretos refratários em canais de corrida principais de diferentes Altos-Fornos de grande produtividade revelaram uma significativa diminuição da velocidade de desgaste do revestimento refratário na linha de gusa oferecendo uma condição operacional segura e confiável às casas de corrida.

Aug 16, 2017

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By J. Shibata

The behavior in electric field of fine particles present in aqueous solution was measured in order to apply to the classification of fine particles. The sample particles used are spherical polystyrene particles with the average diameter of 0.03 µm, 0.1 µm, 1.0 µm, 4.3 µm and 9.6 µm. Electrophoretic mobility and zeta potential of various particles are measured by an instrument based on the principle of the laser Doppler effect. The influence of temperature, electrolyte concentration on the electro-phoretic mobility was investigated for various polystyrene particles. The electrophoretic mobility increases with increasing pH and temperature of suspensions. The measured electrophoretic mobilities are different from electrolyte concentration and particle size. The electrophoretic retardation effect and relaxation effect are considered to explain the behavior of fine particles in electric field by applying the electro kinetic theory of Wiersema et al. For all particle size, the electrophoretic mobility decreases rapidly in high concentration of KNO3 such as 0.1 mol/dm3due to the compression of electric double layer The forces acting the particles in electric field are considered to be electrical force, friction force and some other forces like relaxation effect and electrophoretic retardation effect which appear in ionic behavior. It is considered that the particle moving velocity depends on the particle size. When the particle size is less than 1µm, the velocity increases with increasing the particle size. On the oth-er hand, the velocity deceases with increasing in particle size, when the particle size is larger than 1µm. This phenomenon is considered to be interesting from the viewpoint of classification for fine particles. We found that the electrophoretic mobility of 1.0µm particles is larger than that of 0.1µm particles, and that it is possible to classify fine particles by using the difference of electrophoretic mobility by many experimental results. The phenomena can be explained by the forces acting the fine particles in the electric field. We can apply the behavior to classification of fine particles.

Jan 1, 2014

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By Emmanuel Pornillos

Dado que en el Perú, la actividad minera utiliza el minado subterráneo para la explotación de minerales, se revalúa el uso de estos en pasta cementada para el relleno de las labores subterráneas, así como los relaves desaguados para su disposición superficial. En ese sentido, el presente texto señala las experiencias de diseño y operacionales de sistemas múltiples para la aplicación de relaves en superficie y subterráneo en el Perú, de forma que se pueda optimizar la selección de equipamiento y una operación robusta.

Sep 1, 2013

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By J F. C L Costa, J C. Koppe

It is recognised by the major international codes that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological and grade continuity, etc. However, the difficulty in quantifying the degree of uncertainty associated with mineral resources estimation has led to the creation of a large suite of methodologies, terms and definitions, with almost every mining company having its own set of standards. It is also intuitively known that several traditionally used methods to evaluate resources do not take into account the spatial continuity of the grades, being unable to provide a reliable measure of the error associated with their estimates. Since they do not provide an error assessment, these methods are inappropriate to assess local or global uncertainty associated with an estimate. Faced with these problems, this work aims at developing a methodology for either quantitative or qualitative analysis of mineral resources estimation, through incorporation of uncertainty and the correct definition of the associated risk or error. The proposed methodology includes the development of a software code incorporating all the main classification techniques used by the mineral industry. A comprehensive study about each technique was conducted allowing a comparison of the parameters affecting mineral inventory assessment. A case study was conducted with a typical iron ore deposit data set from the Conceitpo mine of the Itabira Complex in the Iron Quadrangle, Brazil. The results showed the specific limitations of each classification system and the influence in selecting their key parameters, always based on subjective choices.

Jan 1, 2009

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020