Search Documents

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

The history and milestones in the evolution of support systems utilised in the mass-mined chrysotile mines of Shabanie and King are discussed in detail. The use of block caving, false footwall or sublevel caving mining methods brings with it some major support problems, which are exacerbated, in our low rock strength mining environments. The paper discusses the various support elements and systems that have been used successfully or otherwise in these operations. Some predictions for the future of rock reinforcing in our ground conditions are highlighted, in relation to geomechanics, levels of mechanisation and production risk analysis.

Jan 1, 2000

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By André de Albuquerque Vicente

Os aços inoxidáveis duplex caracterizam-se por apresentarem microestrutura bifásica, ferrítica-austenítica. A fração volumétrica ideal das fases é 50% de ferrita e 50% de austenita, entretanto, essa condição é de difícil obtenção quando realiza-se a união por soldagem a arco desses materiais. Neste trabalho estudou-se as melhores práticas de soldagem do aço inoxidável duplex UNS S31803 garantindo a obtenção de frações volumétricas ideais de ferrita e austenita. Foi soldado um corpo de prova pelos processos TIG e MIG-MAG. Para esse corpo de prova foi realizada a soldagem de um passe de raiz e um passe de reforço através do processo TIG e o preenchimento da junta através do processo MIG-MAG. Foram realizados os seguintes ensaios no corpo de prova: micrografia (metal base, ZAC face, ZAC raiz, face da Zona Fundida e raiz da Zona Fundida), medição da fração volumétrica de ferrita, microdureza Vickers (HV500), ensaio de tração da junta soldada, dobramento guiado, Charpy e ensaio de corrosão por pitting.

Oct 30, 2017

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.

By Charles de Abreu Martins

Os efeitos da temperatura de austenitização, taxa de resfriamento e adições de Cr ou Mo nas transformações de fases de um aço 0,12C-1,70Mn-0,2V, utilizando dilatometria, foi investigado. Os diagramas em resfriamento contínuo de sete aços foram elaborados e as microestruturas foram identificadas utilizando microscopias ótica e eletrônica de varredura. Em temperaturas de austenitização mais elevadas, taxas de resfriamento mais altas e maiores adições de elementos de liga (Cr ou Mo), houve uma elevação significativa da temperabilidade e queda na temperatura Ar3. Uma comparação entre os efeitos do Cr e o Mo também foi realizada, mostrando um efeito mais efetivo do Mo. Foi observada redução na temperatura Ms com o decréscimo da taxa de resfriamento. Não foi observada variação significativa de Ms com o aumento da temperatura de austenitização ou adição de elementos de liga.

Aug 8, 2018

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By R. Padilla, M. C. Ruiz, L. Salinas

Chloridizing roasting of bismuthinite (Bi2S3) with NaCl–O2 has been studied to remove the impurity Bi by volatilization from copper concentrates that contain bismuthinite. The study was conducted using mixtures of Bi2S3 and NaCl in a horizontal furnace and TGA apparatus. The variables were temperature, oxygen partial pressure, and NaCl concentration. The chlorination was analyzed by weight loss measurement method. XRD results of calcines reacted for short times in 21% O2, and 850–1000 °C showed the presence of Bi, BiOCl, and Na2SO4, while at longer times in the same conditions, Bi2O3 was identified as a stable phase. Thus, the chloridizing-volatilization of Bi2S3 proceeds through the formation of Bi and BiOCl. Temperature affected significantly the fraction of weight loss of samples. At 600 and 900 °C in 10.3% oxygen, the maximum weight loss was 4 and 20%, respectively. An increment in the partial pressure of oxygen in the range 1–21% affected negatively the Bi2S3 conversion. At normal roasting temperatures (550–700 °C), bismuth volatilization by NaCl roasting was found to be marginal.

Mar 1, 2017

By J Joy, A Bye, G V. Kizil

This paper presents an application of the newly developed risk-cost-benefit (RCB) framework to support risk management decisions for the selection of wall monitoring technologies at an open cut mine site. The RCB framework quantitatively assessed the risk of unstable slope-induced wall failure and its impact on both loss of life and coal recovery. The RCB framework was utilised in the selection of an optimum group of risk-controls to effectively manage the risk of wall failure to ensure safety and optimal production occurred. The RCB framework incorporates mathematical modules that integrated RCB calculations and risk-control effectiveness assessments to determine the risk reduction and financial impact of the examined safety initiatives.This paper provides an overview of the five-staged RCB framework, incorporating the RCB decision support tools, RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control Effectiveness Method), and demonstrates its application to slope stability risk management at the case study site. The RCB charts are designed to display a balance between risk, cost and benefit for easy interpretation by decision makers to support the objective selection of an optimum suite of risk-controls. The RCB analysis revealed that a combination of ævisual inspections, automatic extensometers and radarÆ for fast- and slow-wall failures with structure were sufficient to reduce the probability of loss of life (PLoL) to the æModerateÆ zone as defined by the Australian Geomechanics Society (AGS, 2007) for the case study site. The new framework presented in this paper provides a method to effectively determine the suitability of risk-controls and supports industry efforts to reduce risk to as low as reasonably practicable (ALARP).CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Risk-cost-benefit analysis of early warning technologies impact for wall failure risk management in surface mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 55-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By Ronald Ticona, Marjorie Aubert, Frank Luján

Uno de los principales objetivos en la optimización de los procesos mina a planta es la obtención de una buena fragmentación en la voladura, el cual permitirá generar la cantidad de finos adecuados para la alimentación de la planta concentradora. Con la finalidad de evaluar los efectos de la fragmentación en mina en los procesos aguas abajo desde la voladura, una importante mina de cobre del Perú decidió evaluar el impacto en los procesos aguas abajo de dos tipos de explosivos, de emulsión 100% gasificable con RBS de 118 y de mezcla explosiva gasificada 80/20 con un RBS de 158, en zonas de roca altamente competente con un rango 150 a 160 de UCS y 0.8 de RQD.

Sep 29, 2023

By Raquel de Carvalho Reis

A fosfatização é um pré-tratamento superficial que tem como principais funções: a lubrificação, proteção contra corrosão e proteção contra abrasão. Os metais fosfatizantes mais comumente utilizados são o zinco, manganês e o ferro, sendo o zinco o mais aplicado nas indústrias siderúrgicas, automobilísticas e de linha branca. Atualmente, grande parte das pesquisas relacionadas aos processos de fosfatização é referente ao fosfato de zinco, sendo escasso o estudo sobre fosfato de manganês. O objetivo deste trabalho foi estudar a cinética de formação da camada de fosfato de manganês em aços baixo carbono, analisando a influência do substrato na formação da camada fosfatizada. As análises foram baseadas na obtenção das curvas de ganho de massa, sendo caracterizadas por microscopia eletrônica de varredura. Os resultados indicaram que para o substrato constituído essencialmente de martensita revenida, uma maior quantidade de carbonetos resultou em uma menor taxa de ganho de massa, pois estes funcionam como sítios ativos no processo de fosfatização, fazendo com que exista uma maior densidade de núcleos.

Aug 16, 2017

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

By A. Oja, M. Lahtinen, P. Salonen, B. Saxen

Most of the secondary and low grade zinc raw materials cannot be treated successfully by either conventional roasting - leaching - electrowinning (RLE) process or even by atmospheric direct leaching process. The problems arising especially from high impurity content of these raw materials can be effectively solved by implementation of the solvent extraction process. The utilization of solvent extraction process has been demonstrated by Outotec with raw materials like Waelz oxide, crude zinc oxide and zinc containing concentrator tailings. Based on batch and continuous test work it has been shown that SHG quality zinc can be produced even from the lowest grade raw materials. Impurity control in the solvent extraction process has been examined. The solvent extraction process is the key feature of the whole zinc plant for such raw materials. However, design of the entire zinc process including neutralization and bleed treatment is important for optimization of investment and operation costs of the plant. Very careful evaluation of the zinc process with modern simulation tools is essential. The optimized Outotec zinc process ensures a sustainable and profitable process containing minimal effluent and requiring little residue treatment.

Jan 1, 2014