Search Documents

By N. J. Poll

The Zacarias gold-silver-barite deposit appears to be a Precambrian analogue of present-day exhalative deposits on the sea floor. Geochemical, stratigraphic and structural studies of the latter can be useful in elucidating the ore environment at Zacarias, thereby assisting exploration. The Zacarias mine is about 300 km north of Brasilia, within the Goiás Massif, Brazil. It is the southernmost of three auriferous quartzite occurrences along 1 km of a northeasterly striking amphibolite. Zacarias and its neighboring smaller deposit to the north, the Central Pit, contained a premining ore reserve of 650,000 tons at 4.4 g/t gold, 48 g/t silver, and about 20% barite. Gold mineralization is hosted by concordant quartzite strata also containing layered barite, pyrite, barium-mica, sphalerite, galena, chalcopyrite, magnetite, sulfosalts, free gold, and electrum. The host amphibolite is intercalated with barren mica-quartz-chlorite-pyrite schists that are more voluminous in the footwall and are associated with the ore horizons. Above the amphibolite in the hangingwall lies a thin graphitic shale, then a feldspathic arenite. The strata and regional foliation strike northeast and dip 42° northwest. Crenulation and small-scale folds plunge 30 to 40° to the west.

Jan 1, 1993

By R. A. Thomas, R. L. Solbod

The importance of transverse diffusion on the finger development in a miscible-phase displacement at an adverse mobility ratio of tbree was studied in a porous plate 1/4-in. thick, 3-in. wide and 18-in. long. Fast displacement rates (29 ft/D) and slow rates (1.6 ft/D) were used to determine the effect of residence time on the geometry of the fingers. The shape of the fingers was observed directly by use of the X-ray technique. At fast rates numerous narrow fingers were observed, but at slow rates a single somewhat bulging finger was produced. The amount of material moved transversely by diffusion across the plate was sufficient to modify the finger geometry in the slow-rate run because of the long residence time. These results are in contradiction to some of the postulates in the literature. The composition of the effluent stream, however, was not affected by the flow rate. This result is not inconsistent with the observed change in the shape of the finger in a short model, but it seems likely that a short model does not offer adequate and proper scaling of the reservoir. The model used was probably a valid one for studying the effect of transverse diffusion on the finger geometry, but a longer model would be needed for proper scaling of the effect of the change in the finger shape on the efficiency of displacement as measured by the composition of the effluent stream. INTRODUCTION Fingering can be defined as the uneven advance of the injected phase as it moves into a porous medium displacing the resident phase from the pore spaces of the rock. The use of this term is usually restticted to the situation in which the displacing phase is less viscous or more mobile than the fluid being displaced. Under these conditions, not only are fingers formed, but the length and width of the fingers grow with distance traveled in the porous medium. This subject has become one of great interest to the oil industry because of the present trend toward the use of various forms of miscible-phase displacement to increase oil recovery. Since in nearly all of the known modifications of the miscible-phase displacements an unfavorable mobility ratio exists (the displacing phase has a lower viscosity than that of the crude oil), the conditions are proper for fingering to develop. An appreciable amount of fingering appears to be a severe handicap to these processes for it increases the volume of agent required for the process to be a success, and such an increase puts a severe strain on the economics of the proposed processes. In some cases, such as for a mobility ratio of 200 unfavorable, it has already been demonstrated that the proposed process would not be economic if the fingering in the field were to be of the same magnitude as that observed in the laboratory. A number of aspects of fingering have been studied and reported in the literature. While the phenomenon of fingering cannot be regarded as a completely understood subject, considerable information exists on the effect of the path length and the mobility ratio on the growth of fingers. Less-complete data are available on the effect of the diameter of the flow path on the character and amount of the fingering, and even less agreement in results exists on the effect of rate of flow on the nature of fingering. This paper deals with one aspect of this latter subject. OBJECTIVE The objective of this study was narrowed down to one rather specific feature of the behavior of fingers in miscible-phase displacement in porous media. The variable studied was the effect of rate of flow on the nature and the development of fingers. It should be made clear at this point that, while rate was the apparent variable, the real variable was residence time; that is, at low rates the fluids are present at a given spot in the porous medium for a longer time interval than at fast rates. The purpose of the study, therefore, was to determine the changes which occur in the fingering and the possible benefits which might accrue from a longer residence time during that period when fingers are

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By Peter J. Huck, Yoginder P. Chugh, M. Jennings

INTRODUCTION Large areas of the United States coal reserves have been undermined by room-and-pillar mining over the past century. These abandoned mines generally cause subsidence of the ground surface many decades after mining. Reports from England (1) where there is a longer history of room-and-pillar mining indicate that mines abandoned two centuries ago may still be causing subsidence, and causing surface destruction to urban areas or farm lands that have been developed in the interim. The devastation wrought by subsidence, both in terms of property loss and societal disruption is enormous. The authors discuss here the methods by which subsidence in abandoned mines may be controlled. Two distinctly different subsidence control technologies have been developed in the U.S. for abandoned coal mines. These are referred to as (1) Point Sup- port methods, and (2) Areal Backfilling. As the names imply, point support methods are used to protect individual structures, or even individual foundation elements of structures, whereas areas backfilling techniques may be applied to protect entire neighborhoods or urban districts hundreds of acres in extent. Both point support methods and areal backfilling have specific sub-categories of techniques that may be applied under different conditions as appropriate. POINT SUPPORT METHODS Point support methods are characteristically employed by civil engineers chartered with the design of a new structure or the protection of an existing structure. The subsidence control measures are only a part of a larger project, the safety of which must be assured to a degree of near certainty. The costs of point support methods involve a large number of bore-holes and the use of expensive materials in relatively small quantities. There exist several dozen point support methods, which operate either to support the underground cavities, controlling subsidence, or to isolate the structure from the effects of subsidence if it should occur. The latter methods usually involve deep foundations through the mine opening supporting the structure on the underlying strata. Our concern will be with the former method to support underground cavities to prevent subsidence. Gravel Columns and Associated Methods Gravel columns may be placed in the mine opening using the methods shown in [Figure 1]. Boreholes are drilled through the mine strata, and gravel poured down the borehole to form a pile on the mine floor. When the tip of the pile contacts the mine roof, it is rodded down to spread the pile, and permit additional gravel to be placed. The objective is to place as much gravel as possible in the mine opening, and to achieve firm contact with the mine roof. The gravel pile acts to reduce subsidence by three mechanisms. The filling of a significant fraction of the open mine volume reduces the amount of potential subsidence simply by killing open volume within the mine. In effect, the extraction ratio has been reduced by introducing the volume of gravel. The toe of the gravel pile abuts against nearby pillars, providing lateral support and protection against pillar deterioration. In effect, the height of the pillars has been slightly reduced by burying their lower portions. Finally, some direct support is provided to the roof strata, reducing the roof span and enhancing stability. The gravel column method may be used in a variety of applications, and with materials other than gravel. For example, gravel columns may be placed in a close line around the perimeter of the building to form a continuous gravel wall. The interior of the site may then be completely filled with sand, slurry or other material. Alternatively, a lean concrete may be used in place of gravel, so that the piles achieve significant structural capacity. The grout column, shown in [Figure 2], begins with the installation of a conventional gravel column which is placed around a grout pipe that extends through the borehole into the mine opening. When the gravel column is in place, portland cement grout is injected in stages. At each stage, sufficient grout is injected to fill the interstices in the gravel to build a column perhaps two meters in diameter and a meter tall. The group pipe is then raised one meter, and after the previously injected grout has set, the next stage of grout is injected. The process builds a column of grouted gravel to the

Jan 1, 1982

By Thomas O’Neil

Part 2 of this article continues with a discussion of features that distinguish contemporary investment analysis in mining from earlier methods. Part 1 traced the evolution of evaluation methodology from the traditional and discounted cash flow methods to the present. Quantitative investment models of the past 20 years played an important role in mine evaluation, but a new integrated approach to mine investment decision-making is now developing because of growing economic, technical, and political uncertainties. One of those uncertainties -inflation-was discussed in Part 1. Increased Risk At a time when mineral production technology and analytical evaluation tools have never been more sophisticated, it may seem anomalous to claim that mining ventures are riskier. Whereas technical risk has, indeed, been notably reduced, business risk the chance of a major loss due to market factors-has increased. This has been caused by two factors: the rapidly rising capital requirements of new projects and increasingly unpredictable future economic conditions. These difficulties are compounded by the long lead times of large, new mining projects. Rising Capital Requirements A $100 million investment is no longer considered to be a large mining project in most cases. For a large metal mining project, the total cost of the concentrator alone can exceed $100 million. Amoco Minerals' Thompson Creek molybdenum mine being developed in Idaho will cost over $350 million, for a relatively modest sized (23-kt/d or 25,000-stpd) ore operation with no extraordinary features. For a major grass roots copper operation producing blis¬ter or refined copper, the capital requirements are billions of dollars, not millions. Project costs are higher for two reasons. One, the projects themselves are larger; and two, the capital cost per unit of production is rising rapidly. Projects are larger because lower grade ores, yielding smaller margins, must be mined in greater volume-particularly in view of the high fixed costs of modern technology. When analysts contemplate any capital project, an important consideration is the minimum economic size of the facility. This is the smallest size that can be built and still be competitive on a total unit production cost basis. In the conventional copper smelting business, for example, a production rate of at least 91 kt/a (100,000 stpy) of blister copper is about the absolute minimum for reducing unit fixed costs to competitive levels. Clearly, many variables affect the minimum economic size of a mining facility, but with few exceptions that size continues to grow. Unit capital costs of new mining projects also are continuing to rise. The accompanying table shows that the capital costs in primary copper production have risen faster than the cost of living. Of particular note is the capital charge of over $1.70/kg (77411b) required for a new, fully integrated facility in 1981. Thus, the mid-1982 copper price would not even cover the cost of capital for a new copper producing complex without considering the direct operating costs for such a facility. The breath-taking costs of new mining projects are caused by factors such as increasingly complex technology, the rising social costs of creating attractive living and working conditions for employ¬ees, and the expenditures re¬quired for environmental protec¬tion. For whatever reasons, how¬ever, unit capital costs in mining continue to exhibit staggering growth rates. Future Economic Conditions Risk is not only a function of the size of the potential loss-an im¬portant measure of which is the capital intensity of mining dis¬cussed above-but also of the like¬lihood of incurring the loss. It is here that the ever increasing lead times of mining projects and the glaring limitations of economic forecasting are so important. In comparison to nearly all other in¬vestments, mining has more capi¬tal at stake for a longer period of time before commercial uncer¬tainty is resolved by distant eco¬nomic conditions that are subject to high forecasting errors. A sobering example of the pre¬ceding points occurred with the Lakeshore copper mine in south¬ern Arizona that Hecla Mining Co. undertook to finance and manage in 1969. The project was a joint venture of Hecla and the El Paso Natural Gas Co. and included two mines-one producing oxide ore and a second in the sulfide zone¬and a complex processing facility producing both electrowon cop¬per cathodes and copper precipi¬tates. The project originally was

Jan 12, 1982

By Ian B. Clark

In October-November 1993, the Centre for Cold Ocean Resources Engineering, Memorial University of Newfoundland and University of Victoria jointly carried out reconnaissance surveys at Pine Cove, Baie Verte, Newfoundland. Pine Cove is the site of a multi-year study examining the environmental impact of a shallow water small-scale marine placer gold mining operation. The reconnaissance survey data collected will be used to develop a multi-year environmental effects monitoring (EEM) program for Pine Cove, Baie Verte, but more generally an EEM protocol for shallow water small-scale marine placer mining, which meets the requirements of Canadian government regula¬tors such as Environment Canada and the Department of Fisheries and Oceans. The Pine Cove mining operation is currently scheduled for the summer of 1995, and will use two mining methods: a hydraulic suction dredge in shallow water (<10 meters) operated by a scuba diver, and a hydraulically actuated clamshell dredge in deeper water (-30 m). A centrifugal concentrator will be used to extract the heavy minerals from the mined marine sediments, and the tailings will be returned to the sea floor via a suspended discharge pipe. The reconnaissance work at Pine Cove included geophysical, geochemical, oceanographic and biologi¬cal surveys, providing data which will enable prediction of the potential environmental impacts of the proposed mining operation. The geophysical surveys showed the sea floor to be covered by varying

Jan 1, 1994

Jan 1, 1922

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth&apos;s surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth&apos;s surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex&apos;s findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

Last year in the US alone, about 425 Mt (468 million st) of minerals and coal were beneficiated by froth flotation. This number indicates that from 1983 there was a 10% increase in tonnage of min¬erals and coal beneficiated by the indus¬try. A significant improvement was seen in the tonnage processed by the nonferrous minerals and coal industries. BP Minerals America installed 85 m; (3000 cu ft) flotation cells at the Bing¬ham Canyon mine and concentrator. The new flotation circuit has fewer than 100 cells compared to 2000 flotation cells used in the old plant (Mining Engi¬neering, November 1988). Column flotation use on a commer¬cial scale continues to expand as seen from the interest expressed at the Col¬umn Flotation Symposium (Column Flotation &apos;88). The Magma Copper Co., San Manuel Division replaced all con¬ventional cells with 1.8 x 12 m (6 x 40 ft) column flotation cells for copper con¬centrate cleaning. Also, 1220 mm and 760 mm-diam (48 in. and 30 in.-diam) column cells are operating at the plant in the molybdenum circuit. A commercial Diester Flotaire col¬umn cell for fine coal recovery was installed at the United Coal Wellmore No. 20 plant. The 36.8 m3 (1300 cu ft) cell recovers 13.6 to 18 t/h (15 to 20 stph) of -590 gm (-28 mesh) coal. A similar unit has been installed at Tanoma Mining Co. in Pennsylvania. Various modifications of the column cells are being designed around the world. Jameson (Mining and Metal¬lurgy, 1988) described a new concept whereby the feed and air stream mixture is discharged into a cylindrical column of about 1.2 m (4 ft) height. Recovery and grade of nonferrous minerals have been reported to be better than that in a four-stage conventional flotation clean¬ing circuit. Flotation reagents American Cyanamid and Dow Chemical continued development of a new generation of sulfide collectors. A general feeling is development of new sulfide collectors has not kept up with flotation technology. Additionally, joint efforts between industry and chemical suppliers will likely be necessary to realize the economic benefits of the new technologies, since new chemistries respond differently compared to the conventional collectors. Flocculant development in recent years has been evolutionary rather than revolutionary. Rothenborg reported on development of a new flocculant family (a hydroxymated polyacrylamide desig¬nated S-6703) that has shown consider¬able promise in red mud clarification. Plant testing showed that this new floc¬culant could replace starch and poly¬acrylate and provide significantly higher overflow clarity. Barol Kami (Siirak) and Cleveland¬Cliffs (Hancock) reported development of an amphoteric apatite collector (ATRAC 873) that was used in Tilden&apos;s silica flotation process to increase apatite rejection. The collector was engineered for the particular flotation conditions in the complex Tilden process. Significant plant testing with ATRAC 873 showed that this reagent gave significantly in¬creased apatite rejection without any effect on silica flotation effectiveness or selectivity. Electrostatic separation Electrostatic separation is now em¬ployed in the precious metals mining industry to recover gold and silver grills from crushed slag. The installation at Paradise Peak has prompted other op¬erators to consider this application. In another development, attractive potentials for treating very fine minerals (-45 µm or -325 mesh) are being devel¬oped by Advanced Energy Dynamics and by the Department of Energy. Demonstration tests using triboelectric charging/electrostatic separation have been successful on a variety of minerals as well as coal. Magnetic separation Developments in magnetic separa¬tion have transpired on a production scale. Superconducting, high gradient magnetic separation has gained accep¬tance with the successful startup of a second unit treating kaolin at J.M. Huber Corp. This liquid-helium-cooled mag¬net generates 2.0 tesla in a 3-m-diam (120-in.-diam) bore with no power con¬sumption. Wet, high-intensity magnetic separation has been applied to sulfide mineral separations both domestically and abroad. These continuous type of separators are effective in removing residual chalcopyrite and sphalerite from other base metal sulfide concentrates. Separators using high energy rare earth permanent magnets are continu¬ally increasing. Now offered as both drum and roll type, these units are be¬coming a staple in the processing of industrial minerals. Tests using rare earth magnets strategically placed on a spiral concentrator have demonstrated the enhanced recovery of heavy miner¬als such as ilmenite. Classification Although no major technology break¬throughs in classification appear immi¬nent, there is an increasing need for more efficient and cost-effective meth¬ods to make size separations. It is be¬coming more apparent that mineral concentration methods will be more common at very fine sizes, say below 50

Jan 1, 1989

By K. Malysa

Bubble collisions with ore grains and a selective formation of the bubble-grain aggregates are necessary steps for flotation separation of useful and gangue components of an ore. For the attachment of valuable mineral grain to the colliding bubble a liquid film, separating the bubble and the grain needs to rupture during short time of their collision. High hydrophobicity of the grain surface is favorable because stability of the separating (wetting) film is much lower at such surfaces, that is, the film ruptures faster and at greater thickness. Simultaneously, it needs to be kept in mind and taken into consideration that high affinity to air is a typical feature of hydrophobic surfaces. Thus, when the hydrophobic surface is immersed into aqueous phase the air can stay attached to such surfaces and affect kinetics of the bubble attachment. The paper presents results and analysis of dynamic phenomena occurring upon the collision of the rising bubble followed by its attachment to hydrophobic (Teflon) plates of different roughness. The influence of the Teflon surface roughness, solution concentration, bubble size and impact velocity on bouncing of the colliding bubble, time of the three phase contact (TPC) formation and drainage time of the liquid film, formed between the solid and bubble surfaces, is described. High hydrophobicity, as showed earlier (Malysa et al, 2005), does not assure that each collision leads to the TPC formation and attachment of the colliding bubble. Roughness is the parameter of crucial importance for kinetics of the bubble attachment to hydrophobic surfaces (Krasowska and Malysa, 2007; Krasowska et al, 2009; Kosior et al, 2011). Enlarged roughness of the Teflon plate, from ca. 1 to 80µm, results in shortening the time of the TPC formation (bubble attachment) by over an order of magnitude - from 105 to a few milliseconds only. Higher surface roughness means that larger amount of air can be entrapped in bigger scratches and cavities of the Teflon plate during its immersion into aqueous phase. Results documenting importance of the air presence are showed and mechanism of the air facilitated TPC formation and bubble attachment to hydrophobic surfaces is described. Keywords: bubble collisions, hydrophobic surfaces, teflon plate roughness, TPC formation

Sep 1, 2012

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years&apos; duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.lNST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the persmission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute&apos;s financial year in which the attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.O. Box 1183, Johannesburg.

By H. Schubert

The flotation of sylvite and also some accessory minerals is performed in brines containing very high electrolyte concentrations. Under these circumstances the mechanims of collector adsorption exhibit some characteristics which will be discussed by significant examples: - flotation separation of sylvite and halite with n-alkylammonium salts and n-alkyl sulfates - flotation separation of kieserite and anhydrite with acylamino carboxylic acids - flotation of halite by collectors which are adsorbed by hydrogen bond formation.

Jan 1, 1988

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

By Bjørn Eske Sørensen, Kristian Drivenes, Przemyslaw Kowalczuk, Kurt Aasly, Gavyn Rollinson, Ben Snook

Efficient and successful mineral processing is dependent on detailed knowledge of the materials and minerals that are to be separated and concentrated. Common bulk methodologies such as XRD and XRF are fast and easy, and can provide an overview of the mineralogy and bulk chemistry of the material. However, they will not provide any textural information. Knowledge of the often intricate interaction between minerals in seafloor massive sulfide deposits is crucial in plant design for mineral processing. Samples from the Loki’s Castle hydrothermal vent have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), optical microscopy, Scanning Electron Microscopy (SEM), QEMSCAN, Electron probe microanalyzer (EPMA), and Electron Backscatter Diffraction (EBSD). Processing experiments used froth flotation and leaching techniques. The typical line of operation in ore characterization is shown in Figure 1. Mineral processing may be commenced after any stage of ore characterization. However, it is ideal to have completed as many steps in the ore characterization as possible in order to have the most information of the initial feed material. The main economic minerals in the samples are isocubanite (CuFe2S3), chalcopyrite (CuFeS2), and sphalerite (ZnS), with minor galena (PbS) and trace amounts of Au and Ag. The minerals show complex intergrowth textures down to the nanometer scale. These samples exemplify the need for advanced microtextural analyses to adequately characterize ore material prior to processing. The complex textures hamper the use of flotation as an efficient technique, due to the inability to sufficiently liberate the different minerals and problems with selectively floating isocubanite. Thus, leaching was the preferred method for extracting metals.

Jan 1, 2018

Jan 1, 1929

By E. Kendall Cork

The traditional financial objective for a single mine company has been to operate as frugally as possible and to pay out most of the earnings as dividends. If the business is cyclical (as it is for most metals) the dividends might fluctuate quite widely. When the mine is exhausted the company disappears. This is still quite a viable strategy for a single mine company. It is not however a viable strategy for the world as a whole. The mining industry is built by mine development companies who can mobilize the people and capital to bring new mines into production. Their skills must include marketing, engineering, finance and other politics. It is very rare for a property to be brought in without the support of a major company that can provide all these services. The exceptions will usually have some other form of big brother support, for example the U.S. government uranium contracts at guaranteed generous prices. The mine development company will seek as a minimum to perpetuate itself by developing new mines in order to replace those which are running out. The more common and more ambitious objective is to grow -- that is to add to its ore reserves and current production by developing more new mines. The financial objectives for that company are very different. Obviously if all the earnings were paid out in dividends there would be nothing left to work with. The first financial policy then is to spend an appropriate amount on exploration for new properties. The next is to retain enough of the earnings to provide the capital for new projects at least sufficient for the equity. There is no magic formula as to what proportion of earnings should properly be distributed as dividends by a growth-oriented mine development company. As a rough rule of thumb distributing half or more will probably leave too little to work on and 30% or so is probably a good balance. However the circumstances differ widely from company to company. It may be useful to set an objective for the rate of growth of a company&apos;s earnings. Some have picked rates such as 15% per annum compounded. Others have set a target in real terms which might appear as 10 or 11% plus inflation. Obviously the arithmetic of compound interest is very attractive; however in practice there is much variation. Indeed current returns from existing operations swing widely with the business cycle and there is no assurance that economic new properties will be found according to someone&apos;s arbitrary time schedule. For example, Western Mining Corporation Limited in Australia explored for 30 years with little to show for it, but then found the great Australian nickel deposits and more recently the huge Roxby Downs copper. That long dry spell could not have fitted anyone&apos;s arbitrary calendar of growth and yet they would not have found such orebodies without that long period of effort. Should they have abandoned the search? Once a new property has been found or acquired there has to be a threshold rate of return on the new capital to be invested against which to evaluate the property&apos;s economics. Conventionally this seems to be 15% after tax, a number common in other heavy industries as well. In some cases it is expressed as a lower number plus allowance for inflation. Discounted cash flow analysis is a very useful tool but it does not make the decision. In the end a "go" decision depends on judgment of many factors some of which are numbers used in the DCF calculation whose credibility must be examined. It is curious how frequently investment proposals come in with the rates of return very close to 15%. The project advocates know that a number much less than 15% will not fly and that a number much more is not necessary. With much higher nominal and real interest rates of recent years, even though before tax, logic suggests that the hurdle rate should also rise. The power of compound interest is so great that 20% is very hard to achieve in any cash flow projection but 18% may be a sensible yard - stick. Once again it is remarkable how many project proposals come in with an 18% return. On the record the mining industry as a whole has not been overly restrictive in choosing its hurdle rates of return. This is shown by the abundance of metals in recent years and the failure of metal prices to keep up with inflation. All of the foregoing is standard text book stuff.

Jan 1, 1985

By Stanley Ferguson

Since 1978, the Colorado Department of Health has become involved in specific investigations of possible radiation hazards among nonminers in Colorado communities. In each instance, the improper disposal of mill tailings has precipitated concerns and allegations of radiation hazards. This presentation is a brief summary of the findings, to date, of 4 such investigations involving tailings disposal problems in Canon City, Denver, Durango and Grand Junction, Colorado. Canon City In the summer of 1979, allegations of excessive cancer incidence were made at public hearings concerning an application for a Radioactive Materials License submitted to the Colorado Department of Health by the Cotter Corporation for a uranium mill at Canon City. Canon City is the site of a uranium mill operated since 1958 by Commonwealth Edison. Local residents accumulated figures and calculated rates suggesting a 2-fold excess in total cancer mortality. These rates were not adjusted or standardized for demographic varibles. A review of cancer mortality data and computation of age standardized rates for years 1950 through 1977 showed that Canon City&apos;s cancer mortality rates were within expected limits, actually lower than rates for the State of Colorado or the United States. The first slide shows rates for every fifth year, 1950 through 1975. Further, an analysis of Canon City cancer incidence data from the Colorado Central Cancer Registry revealed that 1979 incidence rates were not significantly different from Colorado rates, with the exception of prostate cancer. The next slide shows age standardized incidence rates for lung, colon, breast and prostate cancer. Data were also reviewed for leukemia, myeloma, lymphoma and cancers of the thyroid stomach, uterine certix, ovary, kidney, bladder-and brain, however, small numbers of cases prevented meaningful rate calculation. 1980 data are presently being analyzed. None of the data yet examined support allegations of radiation-associated cancer in Canon City. Denver In February of 1979, the Department of Health became aware of a number of radium mill tailing deposits in the Denver metropolitan area, remnants of the radium milling industry of the early 1900&apos;s. Several of the deposits were situated so as to possibly contribute significantly to radiation exposure of a small number of people over a period of several decades. The Department developed protocols for radiation surveys, dosage estimates and, for a small number of persons, body burdens determinations and peripheral blood lymphocyte cytogenetic studies. The results of this investigation suggested no measurable biomedical impact as a result of the radium deposits. Durango In October of 1979, a physician residing in Durango, Colorado released information from a preliminary analysis of lung cancer data suggesting an incidence rate several times expected in that city. The data were presented at a meeting of a citizen&apos;s group concerned about the possible health hazards of 2 uranium mill tailing deposits located in the south end of the city. Since cancer incidence data generally do not exist in most of western Colorado, a team of epidemiologists was dispatched to Durango to work with local physicians and hospitals in conducting an epidemiologic study of selected cancers for the period 1969 through 1978. After case-finding and record abstracting were completed, it was determined that sufficient data were available for study of only 3 sites: lung cancer, breast cancer and leukemia. The next slide shows age standardized incidence rates for these 3 sites for 1969-1978 for Durango and the State of Colorado. There are no significant differences in these rates. The data did show a geographic peculiarity with regards to the relative proportion of tumor types near the tailings deposits as opposed to away from the deposits, however, this finding is based upon very small numbers of cases and may represent only the random excursion of rates based upon small observations. This investigation suggests that if a carcinogenic hazard is present, it is too small to be detected by the study method employed. Grand Junction The Department of Health has been involved in the Grand Junction mill tailings problem for several years. In 1966, the Department issued an order terminating the practice of free public access to a 55-acre pile of uranium mill tailings. Prior to this order, an estimated 300,000 tons of material was removed. Of this amount, an estimated 50,000 tons was presumably used in residential and commercial construction. Despite many allegations of cancer and birth defects excesses in Grant Junction since the mid 1960s, the first epidemiologic study of cancer was conducted in the spring of 1977. Data from the Colorado Central Cancer Registry were analyzed and reported to the Executive Director of the Department of Health in June of that year. The findings of the first and preliminary study were an unexplained excess of acute leukemia and chronic myelocytic leukemia. The excess was based upon small numbers but was present across all age groups. No increase in chronic lymphocytic leukemia was evident.

Jan 1, 1981

By Kris van Nijen

IHC Merwede, a Dutch supplier of ships and equipment for dredging and mining activities, and DEME, a Belgian dredging and environmental services group, will enter into a joint venture for deep-sea mining activities. Under their cooperative agreement, IHC Merwede will be responsible for the development and construction of technical solutions, while DEME will be responsible for operations. Together the companies will offer a unique pioneering total solution. The joint venture will be known as OceanflORE.

Jan 1, 2011

By S. E. Phillipson

The MSHA Technical Support, Roof Control Division's primary evaluation tool for coal pillar designs is the Analysis of Coal Pillar Stability (ACPS) program. However, ACPS is limited to evaluating interactions between two seams at a time, which is not ideal for complex multiple- seam scenarios. Further, it does not recognize the influence of strata properties in the interburden and cannot be used to evaluate individual pillars. We apply the Rocscience RS2 two-dimensional finite element program as a complement to ACPS. Complex multiple-seam scenarios can be characterized by a modified pillar stability factor where the ACPS single-seam development pillar stability factor is multiplied by the ratio of average single-seam development stress to the stress in the critical pillar at the multiple-seam stage, using the values of o as predicted by RS2. Several series of test examples involving two-seam analyses with isolated remnants, gob-solid boundaries, and high extraction areas of varying width were used to calibrate simulated gob properties such that the ACPS+RS2 method generated results that matched a traditional ACPS Stability Factor to within 13%. As high-extraction areas become wider and deeper, progressively stiffer gob is simulated by increasing the Young's Modulus property in RS2. After achieving calibration with the test series, three examples of complex multiple-seam scenarios were evaluated, using reasonable properties for strata types and thicknesses based on core log data. Resulting modified stability factors are reasonably close to those predicted by ACPS, although affected by units of sandstone in the interburden and gob shadows superimposed on remnant structures. This tends to show that even in complex multiple-seam conditions, applying ACPS to the worst-case interaction should usually result in an acceptable pillar design.

Jun 25, 2024