Search Documents

By D. B. Carson, D. L. Katz

Natural gases under pressure form crystalline hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methanc-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbon-rich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. Introduction Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural-gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villardl and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Dcaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on tem-peraturcs and pressures of hydrate forma. tion for pure methane, ethane, propane, n-butane, methane-ethane mixtures, meth-ane-propane mixtures, methane-butane mixtures, and some Is natural gases, all- in the Presence of excess water. However, up to the Present time no method has been available for predicting the temperature at given pressures or the pressure at given at at which natural gases will form hydrates if hydrates with water. 'This Paper Presents data on the methane-propane-water, methane-pentane-water and methane-hex-""e water systems in four phases, one of which is the hydrate. he application of the phase rule to the methane-~ro~ane-water data Proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid. equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1942

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By F. Feichtinger, M. Riess, A. Lammer

Introduction This article discusses the unique range of properties of platinum and its applications as a high technology metal. World reserves of this strategic and precious metal are confined mostly to South Africa and, to a far lesser extent, the Soviet Union. An analysis is given of past trends in world platinum output. The timepath is computed for the world platinum output rate, covering a period of more than 350 years. This is based on the postulate that the industrial conversion of a virgin resource progresses according to a Sigmoid curve. This computation is performed by means of a nonlinear, three-stage optimization model employing a multiform Sigmoid function. Finally, the price dynamics are examined. Platinum is the most important of the group of the platinum metals to which it gives its name. Other platinum group metals are iridium, osmium, palladium, rhodium, and rhutenium. The metals occur in nature in close association and are chemically very similar to each other. Three members of the group - platinum, iridium, and osmium - are the heaviest metals known to man. Platinum's density is 11% heavier than gold and about twice the weight of the same volume of silver or lead. Properties Platinum is a typical grayish-white metal. Its special properties were known 1000 years ago to the American Indian craftsmen of what is now Ecuador and Colombia. From those distant beginnings, platinum is now firmly established as the most precious and distinctive metallic element known to mankind. It is shown in Table 1, platinum has a unique wide range of physical, chemical, and mechanical properties including high melting point, resistance to chemical attack, high catalytic activity, mechanical strength, and malleability. These properties make it indispensable for use in many industries. Application Platinum is first and foremost a high technology metal. During the last few decades, fertile scientific minds searched for and developed widespread cost-effective uses for this precious metal. Its unique properties render it irreplaceable in many key industrial processes. Important major fields of application include: • protection of man's natural environment (pollution control), • defense, • fuel production, • fertilizer manufacture, • glass and glass fiber manufacture, • pollution-free energy generation - replacement of nuclear and fuel operated power plants, • electronics, • dentistry, • medicine, and • jewelry. Besides these industrial markets, platinum is increasingly finding a place in investment portfolios around the world as investors switch from gold and silver holdings to this relatively scarce and strategic commodity. Platinum has a growing popularity among private investors. This is being accelerated by the predicted "big crash" of the US dollar and its associated weak currencies, which American financial analysts are expecting towards the end of the decade. Figure 1 shows the demand for platinum in various applications throughout the western world in 1986. The total demand amounted to 88.6 t (97.6 st) of which autocatalyst usage accounted for 32.8 t (36 st) or 37%, the biggest share. Catalytic converter technology is increasingly centered on rhodium-platinum three-way catalysts. These catalysts are able to deal with all three pollutants - carbon monoxide, hydrocarbons, and nitrogen oxides - in a single catalytic unit. The introduction of these three-way converters will result in a further steep rise in the platinum demand for autocatalysts. Among all the metals used in the antipollution devices for automobiles, platinum remains

Jan 2, 1988

It is recognised by the current JORC (1999) code that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological continuity and grade continuity. No prescribed criteria and rules will work for all situations or even between different ore types within the same deposit. Also these criteria and rules are sometimes applied without a clear understanding of their appropriateness, accuracy or correct implementation. For these reasons case studies are useful to evaluate and compare criteria commonly used to assist in resource classification. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody are used as the basis of a case study for the above-mentioned purposes. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce a random sample grid, a semi-random sample grid and a regular sample grid. Using nearest neighbour, inverse distance squared, ordinary kriging and sequential gaussian simulation, block iron grades are estimated using these three blasthole data subsets as inputs. This provides four groups of estimates with the ordinary kriging estimate based on the complete blasthole dataset being considered to represent the true estimate of iron grades. Also generated during this process are estimates of the error for each block. These error estimates range from the simple, such as drill spacing, through to more advanced methodologies such as kriging efficiency and simulation. These estimates of grade and grade estimation error are then compared to the true estimate using graphs and statistics. In order of increasing accuracy the block grade estimation and simulation methods were nearest neighbour, inverse distance weighting, ordinary kriging and finally conditional simulation. The simulation in some instances doubled the accuracy of individual block grade estimates when compared to nearest neighbour and inverse distance weighting estimates. It was found that many methodologies for estimating the error of individual blocks performed equally well with only methods such as average drill hole spacing and classification by search ellipse pass number performing poorly. An approach on how to convert the abovementioned error estimates of individual blocks into a meaningful JORC classification is also discussed. Although advanced non-linear resource estimates are applicable, most iron ore mines are still using relatively straightforward methods. The use of blasthole data and some simple linear interpolation methods and simple linear based error estimates makes this study repeatable for most iron ore sites and their resource geologists. This style of investigation is recommended as a useful approach for the Competent Person to apply to their deposit and thus better select, implement and understand the criteria used for resource classification and provide more consistency and confidence in the resource classification process.

Jan 1, 2002

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors' notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By E. F. Johnson, F. H. Brinkman, H. J. Welge, A. L. Hicks

A method is presented for predicting the character of gas or water displacement in a radial system, which can be either horizontal or inclined. The latter case would comprise cone-shaped or dome-shaped symmetry. The method conriders the one dimension of radial distance, taken parallel to the bedding planes. Approximate allowance can be made for segregation of the two fluids perpendicular to the bedding planes. A complete saturation history can be obtained in about a day's time with the use of a desk calculator. Results of an example calculation agree well with the performance of simulated gas drive in a large model representing a section of a cone. This pie-shaped, sand-packed model was 8-ft long and 4-in. thick. The method of solution is useful in handling other partial differential equations of first order and first degree. INTRODUCTION A new analytical method has been developed for predicting the performance of gas or water drive in a reservoir having radial or cone-shaped symmetry (see Fig. 1). In addition, this new development offers a general method of handling partial differential equations of first order and first degree. This work extends those methods developed previously'- "or predicting the displacement of oil by gas or water in linear systems. The method of calculating oil recovery in a radial system involves two major parts. The first part is a calculation of the distribution of saturations at various times of depletion. The second part is the calculation of oil recovery and producing gas-oil or water-oil ratios through volumetric balance on the saturation distributions obtained in the first part. This second part differs only slightly in principle from similar calculations made with linear systems, for instance. The basic assumptions used in the calculations are as follows. 1. One-dimensional radial flow. An approach is explained later for approximating a second vertical dimension. (With- drawals of oil, and of the driving fluid after breakthrough, are assumed uniform around the periphery of the dome.) 2. Constant-volume fluid flow. Thus, in a gas drive there is no change in gas solubility, or in oil or gas volume due to viscous and gravity pressure drops. 3. Capillary forces are negligible. 4. Constant rate of injection. A program has been written for carrying out the calculations needed on a digital computer. However, a prediction can also be arrived at using a desk calculator; this latter method of work requires about a day's time for each prediction made. CALCULATION OF SATURATION DISTRIBUTION For definiteness, we describe the development of our method for the case of gas drive from the crest of the structure. The reader will note, however, that the method is just as applicable to an advancing radial water drive. The equation describing gas flow over an infinitesimal

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By J. W. Marx, R. H. Langenheim

The authors are to he complimented for a timely presentation of useful information concerning application of heat to oil reservoirs to increase the rate and ultimate recovery of oil. The solution for heated area resulting from constant rate injection of a hot fluid, presented by the authors, and the fluid-flow analogy, solved by Carter,' are particularly interesting in that 110 restriction is placed on the direction of development of the heated area. It is not necessary that the heated area grow radially. Thus the solution could provide useful information for heat injection in any type of well pattern with any specified swept area data. However, it was assumed in the development that the heated region would remain at a constant clevatcd temperature. Vertical heat losses were computed on this basis. Physically. the assumption that the heated region will remain at a constant temperature (independent of distance from the injection point) appears to require that the heat injection medium be stcam, or other condensible gases near the boding point at injection pressure. If a hot liquid below the boiling point or a hot gas considerably above saturation temperature were used, the temperature of the heated region would decrease with distance from the injection well. Lauwerier2 has discussed this problem for a linear system. (See also Jenkins and Aronolsky; and McNiel and Nelson.') Thus, the authors' solution applies more nearly to steam injection than to hot water injection or hot, non-condensable gas injection. Assuming steam as the injection medium, it appears that steam would pass through the constant-temperature heated region and condense upon contact with the unheated sand. The tempcrature in the condensing region would probably be governed by the release of heat of vaporization required for phase equilibrium at the existing pressure distribution. Temperatures in the region would also be influenced by vaporization of hydrocarbon. Thus, it is doubtful that an expression for radial temperature distribution based on heat conduction only (such as the authors' Eq. 9) would have practical significance. As pointed out by Marx and Langenheim, the growth of the heated area under constant rate steam drive will eventually be limited economically by vertical heat loss. The possibility of continuing to move heat economically by cold water injection or by increasing the steam injection rate appears to be a very important consideration. (Movement of liquids away from the injection well should increase injectivity.) Fortunately, the solution presented by the authors may be generalized to thc case of a variable heat injection rate. The general solution is:

In the introduction to a recent paper dealing with, the relationships of magnetite and hematite in the banded iron formations or "jasper bars" of the Western Australian pre-Cambrian(17)t the author made a brief mention of these interesting rocks, of the principal series in which they occur and of a few of the rock and mineral types to be found within them.He drew attention to the essential shnilarity of these Western Australian banded iron formations to those of the pre-Cambrian of such other countries as the United States Lake Superior region, Sweden, South Russia, India, South Africa and Brazil, and gave a brief summary of his views as to the origin of the formations in Western Australia. Furthermore he stated that the banded iron formations have proved of considerable direct economic importance in the goldfields and other' regions of Western Australia, and he referred to the assistance they have provided the field geologist in geological mapping and the determination of geological structures.It is in elaboration of this last statement that the present paper has been written. In the following pages will be found some examples of the use to which the jasper bars have been put in the determination of the geological structure of critical areas in the goldfields of the State.Firstly, however, it may be as well to recapitulate the features of interest in these rocks. The true jasper bars or banded iron formations including the types jaspilite, banded hematite quartzite and banded magnetite quartzite or chert, together with their higher grade metamorphic derivatives such as banded magnetite-gruneri~ quartzites, magnetitegrunerite schists, fayalite ,and hedenbergite bearing handed magnetitegrunerite quartz rocks and' to 'a lesser extent magnetite-hypersthene grunerite quartz rocks, are abundant in the older series of the Western Australian pre-Cambrian. They are best developed in the older Greenstone or Kalgoorlie series of the goldfields districts, interbedded with metamorphosed basic lavas, tuffs and sediments. The mineralogy andpetrology of these rocks, the history of their metamorphism and their origin have been discusseq elsewhere in some detail by the author(19), (20). In one of the papers(20) it was clearly demonstrated that in the light of the true facts the old silicified shear zone theory of the origin of the jasper bars is quite untenable and that the formations undoubtedly represent sedimentary horizons as was recently pointed out by McKinstry(14).It has also been shown that banded ferruginous cherts, quartzites and cherty carbonate rocks of much lower metamorphic grade are well developed...

Jan 1, 1943

By Graham J. Morgan

The following material is excerpted from a presentation Mr. Morgan gave recently to representatives of the financial community. Introduction 1982 was a period of challenge for United States Gypsum Company because of reduced market opportunity. Housing starts for the first 10 months averaged a seasonally adjusted annual rate of 1 million units, 9% below the comparable 1981 period when housing starts were the lowest in 35 years. Industry gypsum board shipments declined 9% from the already low levels of the same period in 1981. US Gypsum met the challenge with stringent cost reduction programs and aggressive action in the marketplace. In late 1981, anticipating market deterioration, the company's management adopted strategies to focus on two shortterm objectives: • Adjust operations to perform profitably in view of limited opportunities through more efficient operations and asset management. • Continue to strengthen U.S.G.'s resources and ability to take advantage of important market opportunities as the economy improves through selective expansion of production capacity in key growth markets. Concentration on these two objectives resulted in a nine month performance in 1982 that, while certainly not satisfactory by company standards, compared very favorably with that of principal competitors in terms of net earnings, margin on sales, and return on average stockholders' equity. To counteract limited market opportunities, U.S.G. focused on productivity improvement, cost reduction, expense control, and maximization of market penetration. Energy Use Improving performance encompassed all segments of operations. For example, efficient use of energy was a significant factor despite lower operating rates at most plants. Overall, in the third quarter of 1982 versus 1972, the company used 27% less energy per unit of production, a savings of $15 million in that quarter alone. These continuing improvements helped to partially offset constantly rising energy costs. A number of operations achieved superior results in the first nine months of the year compared with the same period in 1981. For example, gypsum board plants in Jacksonville, FL, and Sweetwater, TX, recorded 8% and 7% reductions, respectively, in energy use per unit of production. Paper mills in Oakfield, NY, Galena Park, TX, and Kansas City, MO, each reduced energy use more than 12%, while the Greenville, MS, ceiling products facility achieved a 16%o reduction. Safety Safety is another important element that received increased attention. U.S.G.'s safety performance over the past five years has consistently improved. In 1981 it was five times better than that of the gypsum industry; nearly 10 times better than all industry as measured by the National Safety Council; and almost 20 times better than all US manufacturing as recorded by the Bureau of Labor Statistics. In addition to human concerns, this excellent record results in significant dollar savings that directly affect company results. In 1981, U.S.G.'s pre-tax savings in claims, premiums, and related expenses were about $20 million compared to the industries in which it competes. For the first half of 1982 performance improved further, with a cumulative lost workday incidence rate per 200,000 man-hours worked of only 0.27, an all-time record. Expense Control Careful control of inventories and receivables also received special attention. As of Sept. 30, 1982, inventories were 29%, or $44 million, below the level of Sept. 30,

Jan 2, 1983

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

By AIME

HAPPILY, a large group of the non-ferrous fraternity have long valued a personal association with the new Chairman of the Institute of Metals Division. Many others who will meet him, either officially or unofficially this year, will find themselves sharing the enthusiasm with which he has been welcomed to his new office. Albert A. Smith, Jr., was born at Butler, N. J., on Dec. 28, 1904, and moved to New Haven in time to initiate his preparation for Yale University on the home grounds. After receiving a B.S. degree cum laude in 1926, he stayed on for graduate work at the Hammond Laboratory under C. H. Mathewson, and was awarded an M.S. degree in 1928.

Jan 1, 1948

By AIME

WE produce Charles Van Ormer "Charlie" Millikan as living proof that man need not make a loud noise to be heard. His quietly affable, analytical, and soft-spoken manner in the face of all problems belies his ability to "get tough" when the situation demands it. As a chief engineer with many responsibilities for the success of a large producing company there must have been many occasions to tempt Charlie to excitement, but there are few, if any, who can say they saw him yield. He has an abiding faith in the benefits of hard and persistent work and will not admit the existence of a problem that cannot be reduced by it.

Jan 1, 1948

By P. R. Bailey

The use of carbon for the recovery of the gold dissolved in cyanide leaching began with a pilot unit at Barberton in 1977. This was quickly followed by larger scale plants at Modderfontein (1978), President Brand (calcine 1980), Western Areas (filter tails 1980) and Beisa (primary ore 1981) and has grown to become the preferred process. There are currently 34 operations that use the carbon in pulp/leach process which accounts for 35 percent of South Africa's gold production. The size of individual plant varies over a wide range.

Jan 1, 1993

By Teruyoshi Narita

In Japan, the Ministry of Economy, Trade and Industry (METI) commenced a research and development (R&D) project on seafloor massive sulphides (SMS) in Japan?s exclusive economic zone (EEZ) in the 2008 fiscal year. In this plan, the road map of Resource evaluation, environmental impact study, mining system technology and processing technology fields consisting of the first and second stage has been shown for the commercialization of SMS. Based on this road map, Japan Oil, Gas and Metals

Sep 14, 2011

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By J. Trimble, B. M. Davis, D. McClure

During initial mining operations at the Colosseum gold mine, discrepancies between the average blasthole grades and mill-head grades were quite large. In December 1987, mill-head grades averaged 39% lower than corre¬sponding estimates from the blastholes. The correlation between average blasthole grade and mill-head grade had an r-value of 0.015. The magnitude of the discrepancy and the lack of correspondence between estimated and actual grades led to a series of investigations of the sampling system, the effect of blast movement of the ore, and the estimation methodology. The discrepancy between blasthole grades and mill-head grades had been reduced by about half on a percentage basis at the conclusion of these studies. Ongoing studies have produced changes that reduced this discrepancy to its present level of less than 10%. Geology The Colosseum mine is within the Clark Mountain mining district about 68 km (42 miles) southwest of Las Vegas, NV in San Bernardino County, CA. Gold mineralization at the deposit is hosted in two 152 m x 213 m (500 ft x 700 ft) interconnected, rhyolitic intrusive breccia pipes that intruded Pre¬cambrian crystalline basement rocks and overlying Paleozoic marine sedimentary rocks. Subsequent erosion (deroofing) of all of the Paleozoic section and a portion of the Precambrian section has exposed the pipes to the present level (probably a significant depth in the original breccia pipe system). Lithologies exhibited within the breccia pipe complexes include rhyolitic felsite, and breccias of felsite and wall/ country rock. Breccia types grade from felsite plus Precambrian granite-gneiss fragments in an aphanitic felsite matrix to crosscutting breccias of felsite, Precambrian granite-gneiss, and Paleozoic sedimentary rocks in a matrix of finely comminuted material of the same composition. All the lithologies in and around the breccia pipes exhibit moderate to intense quartz-sericite-pyrite alteration, with sericite and pyrite the dominant visual alteration minerals. Gold at the Colosseum mine is generally submicroscopic and associated with sulfide mineralization, chiefly pyrite. It occurs as free gold, with minor alloyed silver. It is primarily in contact with pyrite in fractures or along pyrite grain edges. Secondarily, it appears as isolated particles in quartz and other gangue minerals but spatially always close to pyrite, and rarely as particles encased in euhedral pyrite. The pyrite mineralization and minor base metal sulfides occur in three distinct styles: as disseminations, as open space or vein/fracture filling, and in breccia clasts replacing dolomite. The pyrite megascopically ranges from absent to 30% of rock volume within the breccia pipes. Although the gold at Colosseum is apparently spatially and geochemically associated with pyrite, there is only a general proportional relationship between pyrite content and gold content. Sometimes, a high volume percentage of pyrite has only geochemically anomalous gold. This makes visual pyrite only a general grade control tool and not a specific tool. This further makes the ore control process at Colosseum all the more difficult. Initial grade control procedure Initial grade control was based on blasthole samples collected in two stages by an "automatic" sample collection device (rocket sampler). A sample was collected for the top 3 m (10 ft) in a hole. The bag was then changed so that a sample was collected for the lower 3 m (10 ft). Each sample was prepared and fire assayed to determine the grade. Large discrepancies were sometimes noted in the assays of top and bottom samples. The samples were averaged together and a plot was made showing the blasthole locations and their associated grades. Discrimination between ore and waste was based on as-

Jan 1, 1989

By Tell Ertl

An annual invitational address by an outstanding man in mining, geology, or geophysics who has contributed significantly to the progress of technology in these fields. IN 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it. E. D. Gardner was born in West Jordan, Utah, in view of Little Cottonwood Canyon, the site of the Emma Mine. Park City in the Wasatch Mountains a few dozen miles to the east, and Tintic, not much further to the south, were developing their vast ore-bodies throughout his youth. As a boy he was near the present Midvale metallurgical area and could see the Lark and Bingham Canyon mine dumps and imagine the mining activities at Tooele, Ophir, and Mercur just over the nearby Oquirrh Range. He was 11 years old when the first car of copper ore was shipped from Bingham Canyon. It was not surprising that he attended the University of Utah and graduated with an engineer of mines degree. Five years with the Utah Apex in Bingham Canyon as chief engineer and assistant superintendent completed his training for the 44 years of unselfish and lightly rewarded service he was to give the mining industry as a Government engineer. All of us in mining are familiar with the great work he carried on and directed during the genera- tion he supervised the Southwest Experimental Station at Tucson. He has written scores of papers and books. His observations and experiments on drilling and blasting have led to the important improvements in this field during the past quarter century. Whereas those of us who consider ourselves widely informed about underground metal mining methods make hasty trips through a half dozen or dozen mines a year, our conferee has visited them all—not only the metal mines, but also coal and hundreds of nonmetallic mines, in the United States, Canada, Latin America, and overseas. His keen observations and analytical mind have resulted in an encyclopedic knowledge of mining and mines. His improvements in mining technology have been steady and predictable. His elucidation of mining problems to the many young engineers that have come under his guidance have made them grow strong and useful to his industry. When he chooses to stop, his influence will continue to expand and prosper because of the inspiration and dedication he instilled in so many of us. The profits from his ideas have been distributed throughout the mining industry. He has remained a technical man who felt that he could serve the mining industry best as a Government engineer. But he is the staunchest advocate of the belief that the public should gain from his work through private industry. This is not the first recognition E. D. Gardner has received. The Department of the Interior awarded him the coveted Medal for Distinguished Service in October 1949, and he received the Engineering & Mining Journal's Salute in March 1951. His friends who are presenting him the Daniel C. Jackling Award today know this great mining engineer simply as "Ed" Gardner.

Jan 1, 1956

By W. W. West

MACHINERY used for size reduction of materials may be divided into three classes-depending upon the manner in which the crushing force is applied. In the first class could be listed the primary crushing units, such as the jaw crusher and gyratory crusher-which crush to coarse sizes by applying pressure intermittently between converging surfaces. In the second class may be listed crushing units, such as the hammer mill, roller mill, and ball mill, which crush principally by grinding or attrition. In the third class is the impact mill which, as the name infers, crushes by impact. The second and third classes generally include machinery used as secondary units for intermediate or fine crushing and grinding. Theory of Crushing by Impact Throw a stone into the air and give it a severe blow while it is momentarily suspended, and it shatters into several pieces. The impact crusher uses this "batting" principle, but carries it one step further. As the material to be reduced enters the crushing chamber, it receives a severe free-air impact blow by hard-hitting beaters suspended from rotor discs. The shattered particles formed are then driven at high velocity against impact blocks, where a further reduction in particle size takes place. The rebounding particles from the impact blocks are again caught by the beaters, and the process repeated until the material is swept out of the open bottom of the crusher. Impact Crushing Versus Attrition Crushing Fig. 1 shows a Hammermill type of attrition crusher. This particular mill has central feed and is reversible. Because of the central feed, an impact section can be designed into it at the feed entrance for preliminary crushing, followed by the cage bar attrition area for final sizing. The material is caught and held in a crushing chamber enclosed by grate bars or perforated plate. It remains in this chamber until it is reduced to particle size small enough to pass through the openings between the bars or in the plate. In this manner the top particle size discharged from the mill is closely controlled. As the swinging hammers pass through the bed of material, the material is broken down by a scrubbing action between hammers and material, material and grate bars, and material against material. This attrition produces a rounded particle shape, accompanied by slivers and a comparatively high percentage of fines. The crusher is especially useful in industries where the material treated is not too abrasive, such as limestone, cement or coal plants. It can be readily understood that from the maintenance standpoint, it is not suitable for hard abrasive materials such as refractories and aluminum oxides. One common type of impactor is shown in Fig. 2. The bottom of this type crusher is entirely open and the passage of the material through the crushing chamber is almost instantaneous. Liberal clearances are maintained between the impact hammers and the anvil type breaker blocks. This eliminates practically all attrition. It is the elimination of attrition that makes the impactor particularly adaptable for reducing hard, abrasive materials. The impactor is also well suited for the reduction of wet or frozen materials, which clog an ordinary Hammermill. Particles broken by impact, when examined under the microscope, show a distinct tendency toward rough, cubical shape, with a minimum of fines. Another important factor in impact crushing is that crushing is accomplished along natural cleavage lines, thus freeing foreign ores or materials.

Jan 1, 1952