Search Documents

By M. Di Tommaso

Acid Mine Drainage (AMD) is a quite diffuse environmental problem in dismissed sulphur mine districts. AMD is related to sulphur oxidation of abandoned tailings, generating heavy metal-bearing streams with high iron and sulphate contents and low pH. Treatments of AMD aim firstly to increase the pH to reduce its leaching power causing the further release and mobilization of heavy metals through soil solution and groundwaters. Increasing the pH also allows the precipitation of iron (III) (involved in sulphur oxidation and then in AMD generation) and the partial removal of other toxic components such as arsenic. pH adjustment and the reduction of the high concentration of iron are also necessary for the successive biological treatment in permeable reactive barriers (PRB) with sulphate reducing bacteria (SRB) (II step, biologically mediated precipitaton/biosorption) to avoid the rapid plugging of the barrier (for the large amounts of iron precipitates) and to ensure neutral pH conditions for SRB growth. In this work the first step (chemical precipitation) of a combined chemical and biological treatment of AMD is presented. Experimental data from column tests using carbonate stones to remove iron and increase pH were reported. Toxicity tests have been carried out on the treated wastewaters by Lepidium sativum.

Jan 1, 2006

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

Traditionally, the term ætotal systemÆ design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal ætotal systemsÆ approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

By Waldram JT

The Kelsey Centrifugal Jig incorpo- rates the principles of operation of a conventional mineral jig, at the same time utilising high centrifugal forces to extend concentration to very fine heavy minerals. The main operating variables which are adjusted to control processing of different types of material are centrifugal force, ragging material and size distribution. Pilot plant trials have been under- taken to examine concentration of a mineral sand in which the heavy mineral particles occur mainly in the minus 0.075 plus 0.032 mm size range. Stage recoveries of greater than 90% were achieved at concentration factors of up to 2, although lower recoveries were obtained with higher concentration factors. A final concentrate containing 65% heavy minerals was obtained.

Jan 1, 1986

By P Allum

This paper presents a case study to reduce the operational cost on the secondary ball mill circuit in the Lead/Zinc Concentrator at Mount Isa Mines. The circuit includes two five-metre diameter ball mills each closed with a cluster of ten 15-inch cyclones. The operating cost for both ball mills is about six million Australian dollars per annum.The concentrator achieves 75 per cent of the plant design capacity with one ball mill operating, but will have to use two ball mills when 100 per cent plant capacity is required. The optimisation study on the circuit identified a new flowsheet that enabled the concentrator to reach 100 per cent of the capacity by using one of the two secondary ball mills. The success of the project utilised the existing equipment rationally and saved the operational cost for one ball mill at full concentrator capacity. A further simplified secondary circuit is proposed using the IsaMill for the secondary grinding duty. Performance of the IsaMill circuit and the potential cost savings are predicted.

Jan 1, 2002

By Gutsche O, Kapur PC

Experimental data on the production of fines as a function of specific grinding energy consumption show that in general the energy utilisation in a choke fed high-pressure roll mill is higher than in a ball mill, but lower than in the single-particle mode of comminution under slow compressive loading. There is some evidence to suggest that the presence of water in feeds improves the energy efficiency of pressurised roll milling somewhat. Within a wide range of energy input, the size distributions of the ground product are self-similar, the logarithmic median size decreases linearly with the amount of fines produced and the inverse of the median size increases linearly with the energy spent. The production of fines as a function of energy expended follows essentially the same pattern as the one frequently encountered in media mills. The kinetics of grinding in the high-pressure roll mill can be simulated satisfactorily by modifying the standard particle population balance equation in order to account for energy dissipation in the tightly compressed bed. Common characteristics and important differences in grinding by the media mill and the high-pressure roll mill are highlighted.

Jan 1, 1993

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By N. J. Grant, D. S. Bloom

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By K. Th. Mavrommatis

Cleanness of steel is justified, measured and estimated in steelmaking process through different concepts which are mainly based on operational, empirical or semiempirical parameters and describe ?cleanness as a state?. In this work a theoretical concept is developed, considering ?cleanness as a process? and introducing a dynamic aspect into the quantification of cleanness of a steel melt, linking operational parameters with physicochemical variables, which are based on first principles. This concept and the here derived and developed variables and parameters are based on the earlier defined agglomeration index (AI) of a steel melt, the ratio of the mean inclusions diameter (MID) to the mean inter-particle distance (MIPD), which is shown to be a measure of the agglomeration tendency of the melt after deoxidation, and can serve both, to monitoring cleanness during steelmaking operation and to be useful as a basis for mathematical modelling of cleanness and of the metallurgical measures in plant, associated with production of clean steels.

Jan 1, 2006

By Frank Firmstone

SINCE the blast fired August 15th, 1878, which was described by Mr. Clark,* and up to November, 1881, we have fired three smaller blasts, one in the: southwest corner of the quarry and two in-the but-tress of rock Left standing by the first blast rear the mouth of the main gangway. We intended to keep an exact account of the stone thrown down by each blast, but the large quantity required by, the furnaces since the beginning of 1879, and the time taken up by more important matters, have caused this to he neglected, so that it is not possible to separate exactly the, cost and quantity of stone obtained during this time by the old method from that furnished by the large blasts; yet as the latter quantity has beet much greater than the former, some notion of the value of the Jarge-blast plan may be reached by comparing the figures from September, 1878, to November, 1881, with those for times when the old system was exclusively used. Since 1878 wages have been raised, lowered, and again raised, and to get a year of sufficiently large production for fair comparison it is necessary to go back to that ending April, 1872, when wages and supplies were different from present prices and from those of 1878. * Transactions, vol. vii, p. 266.

Jan 1, 1882

By Emerson D. W

The search for economic mineral deposits is becoming more difficult as exploration goes deeper in the established mining camps and spread out to the surrounding covered areas, which may have an `overburden' some hundreds of metres thick. Geophysics is finding an ever increasing role in such exploration. When the target is zinc, the task often becomes even more difficult since sphalerite, the most commonly mined mineral, is non-magnetic, resistive, and relatively light compared to other sulphides. Fortunately, sphalerite commonly occurs in association with other sulphides, which are magnetic and/or conductive and/or heavy, thus most zinc-rich orebodies have at least one contrasting physical property to aid exploration. This paper presents the physical properties of sphalerite and other potentially important zinc minerals. Results of petrophysical measurements of samples from various zinc-rich ores are presented together with examples of geophysical surveys over a number of zinc deposits. The results show that the physical properties are not merely dependent upon the properties of the orebodies' constituent minerals. For example, the small (0.4 Mt) and low-grade (five per cent Zn + three per cent Pb + two per cent other sulphides) Flying Doctor deposit at Broken Hill, New South Wales (NSW) is much more conductive than the large (3+ Mt) and high grade (14 per cent Zn + five per cent Pb) Cadjebut deposit in Western Australia (WA). In the former case, tectonic stresses have

Jan 1, 1993

The Joint' Venture Method is a procedure for assessing the value of exploration properties, particularly those for which resources have yet to be delineated. It aims to convert the terms of an actual or synthetic joint venture into the equivalence of an arms- lengths cash transaction between a willing seller and a willing buyer. This paper sets out one approach to achieving that conversion. It discusses both simple and complex cases and gives some examples from both public and private documents. It also includes some case studies in which the Joint Venture Method of valuation can be compared with values derived for the same project using other methodologies including actual cash deals. The Method has failings in both mathematics and logic. However because it does reflect or simulate an arms-length deal which takes into account past exploration effort and expenditure and an assessment of prospectivity at a particular point in time, it is felt that it can provide a reasonable approximation of trade value or asset value of a prospect, particularly if used in conjunction with other methods.

Jan 1, 1994

By C. Bazin, D. Hodouin

Dynamic experiments were performed in a continuous open-circuit 40x40-cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transferfunction and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model, a minimum variance controller with constrained input is designed and its performances are compared, by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (S//W) provides a wide spectrum of utilities ranging from improving field acquisition techniques, data processing and interpretation of coal seismic data. The power of the workstation lies in the interpretation process where various sets of geophysical and geological data are integrated to form a network of information that is stored in a database. Computer models are generated from known borehole and geologic information and later cross-correlated with the processed seismic data. Structural and stratigraphic modeling techniques add another dimension to the interpretation process. Complex trace attributes highlight subtle features not easily observed in black and white sections. Using the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1992

By P Mavros, K A. Matis, N K. Lazaridis

A large number of techniques are in use today to limit membrane fouling, among them certainly is air bubbling (which constitutes the transport medium in flotation) as applied in wastewater treatment; meanwhile, dispersed-air flotation is suitable as a pretreatment stage for microfiltration. The invented and investigated hybrid cell combines the advantages of both flotation and membrane separation, while overcoming their limitations, producing clean water from industrial wastewater. Metals recovery from dilute aqueous solutions is a promising application of this innovative hybrid process of flotation and microfiltration, further to solid/liquid separation. In this study, ceramic flat-sheet membrane modules were inserted inside a typical flotation cell in the laboratory tests, using multichannel geometry, combining flotation with microfiltration by submerged membranes; the latter requiring periodic backflushing. The specific objective was to apply this process for the efficient separation of effluents containing metal cations (here, zinc). The main examined parameters were: the initial metal concentration, flotation surfactant applied and air flowrate. The successful contribution of precipitate flotation was highlighted, while the observed metal removals were of the order of ~100 per cent.

Jan 1, 2005

In the last few decades, a considerable amount of effort was directed at accurately determining the coal pillar strength to use for safely designing coal mines. The outcome of this early work was the well known Obert-Duvall, Holland-Gaddy, Bieniawski, and Salamon-Munro equations for coal pillar strength. All of these equations were developed for, and were calibrated with, pillars in a large room-and-pillar area such that the loading could be determined using the "tributary-area" theory. In order to account for the abutment loads associated with full-extraction mining, the empirical methods have typically adopted a simple conceptualization of the abutment load through use of an "abutment angle." Short of a complete numerical or analytical analysis of the coal seam and surrounding strata, very little work has been Fretted toward refining the empirical analysis of pillar loading. It appears that the vast majority of the research has been directed at determining the pillar strength, the numerator of the safety factor equation, when the denominator of the safety factor equation, the pillar loading, plays an equally important role in pillar design. This paper will address the deficit of pillar loading research by exploring the accuracy of the empirical abutment load calculations using insight provided by an elastic overburden model, a laminated overburden model and field observations. Ultimately, it is determined that a constant abutment angle probably over-predicts the abutment load as the mining depth increases.

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006

Stringent controls now placed on the quality of coal make it important to be able to predict not only the tonnage and the grade of the coal in situ, but also the recovery factory and average grade after the coal has been washed. The established techniques of linear geostatistics (ordinary kriging) can be used to estimate the total tonnage and the grade of the coal in situ, but more sophisticated techniques are required for predicting the characteristics of washed coal. Two approaches are currently being investigated at Fontainebleau. One involves a parametric model of the washability curves and disjunctive kriging. This is described in Armstrong (1980(a) and (b)). The other is similar to the service variable approach used for estimating recoverable uranium reserves. The method is described in this paper.

Jan 1, 1985

By C. S. Chang

PEARL starch, a corn starch prepared with a minimum of alteration, is a good selective depressant for iron oxide minerals.1 From what is known of the complex chemistry of corn starch, there is evidence that it consists of a mixture of saturated giant polymeric molecules, both straight and branch- chained, the constituents consisting of glucose units with hydroxyl radicals as active or polar groups. To add to the existing knowledge of the chemistry of the flotation process, it is desirable to ascertain the effects on the corn starch as an iron oxide depressant when some of the hydroxyl radicals are replaced by other active groups that are common to flotation reagents. The ideal way to carry out this investigation would be to test reagents containing different active groups derived from corn starch. The preparation should be such that the reagents possess the same degree and location of substitution and are ac- companied by little or no degradation of the starch molecules. This, of course, is almost impossible to realize, as it is difficult to control the degree and location of substitution as well as to prevent degradation of the starch molecule during preparation.

Jan 9, 1954