Search Documents

By James L. Hendrix, David Castillo

Cyanidation is one of the most common practices used in the extraction of gold and silver. One method of application is heap or dump leaching which entails the leaching of the gold or silver ore by spraying or dripping a cyanide lixiviant over the ore and collecting the effluent. The ore is placed on what is known as a leach pad system. A typical leach pad system consists of a foundation, a leakaqe detection system, a liner, and a cover layer (Strachan and van Zyl, 1988). There are many types of liners available for use. The type of liner depends upon what type leaching pad system us used. Generally, leaching pad systems can be categorized into two types: an expandable pad and a reusable pad. An expandable pad exposes the liner to the elements only in the initial stages of ore placement on the leach pad system. A reusable pad exposes the liner to the elements on a periodic basis. In addition to the exposure to the elements, the liner is also under the stress of the ore placed on it and the stress of the vehicular traffic across it. These stresses and exposure to the elements are the major causes of liner failures, which can appear as punctures, tears, cracks, and deterioration. Because of the possibility of the failure of the pads to contain cyanide-laden solutions the designs for liners of pads and ponds have become more and more stringent. Currently, though, there is some recognition that in some locales such stringent design criteria may not be required (Chatwin, 1989). Some soils have significant cyanide attenuation and degradation capacity. It has been found that soils containing carbon- aceous materia1 wi11 remove cyanide from solutions percolating through them (Chatwin, 1989). Of course metallurgists have long recognized the deleterious effect of carbonaceous material in the mill circuit. Sheridan, et a1 (1988) have shown that WAD cyanide is detected in the effluent of a 2 m column filled with ground carbonaceous ore only after it had been continuously washed with greater than 9 pore volumes of NaCN solution. It was decided to examine the potential of successfully attenuating cyanide by placing an organic material layer between a 1iner and the prepared soil base. One consideration for the selection of the organic material was cost. Sawmill wastes, ground agricultural wastes (such as corn cobs), and other organic wastes were considered. But the first waste to be tested was a product found at any metropolitan area, sewage sludge.

Jan 1, 1990

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By M. Takebayashi, M. Shingu, H. Nagai, T. Nakai, S. Asano

The Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. (SMM) is located in the coastal zone of Saijo City and Niihama City, Ehime Prefecture, Japan. The refinery has been producing copper, sulfuric acid, and precious metals such as gold, silver, and PGMs. Previously, the process of precious metals recovery was a combination of pyrometallurgy and an electro-refining process with the conventional cupellation for around 400 years. However, this process had some major problems such as non-efficient recovery of valuable metals, high environmental risk by pyrometallurgy, high cost for maintenance of equipment and so on. In order to solve these problems, a thorough hydrometallurgical process for precious metals refining using chlorine leaching technology was originated and developed by Sumitomo and thereafter commercialized in 2004 at Toyo Copper Smelter and Refinery. This new process enabled shorter-term recovery of gold and manpower saving, and occupational safety and working conditions have also been improved. Superiority over the existing hydrometallurgical processes was also confirmed, for example by the achievement of 99.99% pure silver production without an electro-refining process. This paper summarizes the hydrometallurgical technologies for precious metals recovery such as chlorine leaching of copper anode slime for silver recovery, solvent extraction (SX) for gold recovery, and ion exchange (IX) for PGMs recovery. It also presents a unique silver purification process. INTRODUCTION Sumitomo Metal Mining Co., Ltd. (SMM) produces copper, precious metals and rare metals as by-products at the Toyo Copper Smelter and Refinery, and nickel and cobalt at the Niihama Nickel Refinery. Precious metals contained in nickel ore are also separated and refined at the Toyo Refinery after concentration. SMM has been refining precious metals using the pyrometallurgical method. In recent years, we have revamped the separation and refining process of precious metals dramatically by making use of advanced hydrometallurgical and engineering technology developed in the company. In this paper, we introduce the history of development and techniques of this process, and also introduce in detail the technologies of gold refining, PGMs recovery, selenium recovery, and silver refining which have been particularly difficult to achieve.

Jan 1, 2019

By William Kent

In a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on " Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron procluced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the " furnace hook," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable callses which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wetor dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1879

By William Kent

(Read at the Amenia Meeting, October, 1877.) IN a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on "Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron produced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the "furnace .book," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable causes which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wet or dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third. class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1878

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By Arthur F. Wendt

IN 1697 King William the Third granted unto his well-beloved subject Adolph Philipse, a certain tract of land, now known as Putnam County, N. Y. At the death of Adolph Philipse the land descended by inheritance to his nephew, Frederick Philipse. In 1751 his surviving three children partitioned the surface into nine parcels and divided them equally amongst themselves, but reserved the mineral rights which they held in common. Thus, at this early period in the history of the colonies, the existence of valuable deposits of iron-ores in Putnam County seems to have been a matter of common knowledge. Yet it is only within the last five years that the county has become a prominent, producer of iron-ore. Desultory mining had been carried on before that period at the Sump, Croft, arid Tilly Foster mines, but only a limited output was achieved, and few of our iron-masters suspected the existence of an abundance of good ores only forty miles from New York harbor. The accompanying map shows the location of those deposits of ore which are now generally known, and have been worked to considerable extent. Without doubt there are many more still awaiting the miner's pick, for no systematic exploration has ever been attempted within the borders of the county. Geologically, the occurrence of the ore is a counterpart of that of the New Jersey and Lake Champlain magnetites. The countryrock, and even the physical geography, are identical. Many small lakes dot the surface of the county. It is from these and their tributary springs and streams that the metropolis derives its farfamed Croton water. Abrupt hills divide the lakes and ponds. Some of the lakes, notably Lake Mahopac, are on the crest of hills, and are fed by subterraneous springs. The prominent mines of the county, in the order of their productiveness, are the Tilly Foster, Mahopac, Croton Magnetic, Sump, Croft, and Island mines. Of these, the first two are at present the only producers, and are quite exceptional in their nature. In fact they are the only ones of their kind in the Appalachian range, if not in the world.

Jan 1, 1885

By Ernest R. Darby

WHEN bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag maybe incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal. When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not mixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 lb. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 lb.-over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

Jan 1, 1928

By B. B. Zavoico

After showing continued and very satisfactory progress until the close of 1931, the oil industry of the Soviet, Union experienced very great difficulties, and since 1932 has not only failed to complete its assigned quotas but has fallen farther and farther behind them, and in fact during 1932 and 1933 Russian production has been below production in 1931. In 1934 the total crude oil production of 169,200,000 bbl. exceeded that of the former peak year, 1931, when 156,100,000 bbl. were produced. The production during 1934 amounted to 78.65 per cent of the plan. The failure to complete the plan has been due to the inability of the oil trusts to develop new fields; the fields that have been producing since 1917 still account for between 75 to 80 per cent of total production. The failure of the Soviet Government to develop new fields has been due to unsatisfactory organization of the geological work, to the extremely slow drilling of wells and their exploitation, and to the very much delayed development of the few areas that have been discovered. The official overestimation of the proven reserves of the country has undoubtedly been an important factor in giving the Soviet industry too much confidence when actually such reserves have been small. The official Soviet estimate of proven reserves of Russia is now placed at 21,000,000,000, bbl., while in fact such reserves, if estimated on a conservative basis, do not exceed 4,200,000,000 bbl., as will be shown later in this review. The refinery branch of the industry also showed unsatisfactory results with a recovery of gasoline, both straight-run and cracked, of only some 16 per cent of the total runs to stills. In fact, the showing of the refineries has been so unsatisfactory that the exports of gasoline have been greatly curtailed from 1933 to 1934, dropping to 10,000,000 bbl. in 1934 from 12,230,000 bbl. in 1933. With the indicated increase in domestic demand, together with but slightly increased refining capacity, the volume of available gasoline for export probably will be reduced to about 6,000,000 bbl. during 1935. The geographic distribution of constructed refineries has been unsatisfactory and the crude oils from Baku had to be transported by tankers

Jan 1, 1935

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By Thomas Leonard Watson

Sulphide ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually py-rite or pyrrhotite, or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another ; garnet, am phi-bole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William counties, located on the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodics is the famous " Great Gossan Lead" (13, Fig. 1) of the Floyd-Carroll-Grayson coun-

Jan 1, 1908

By Burton Atkinson, David Johnston

Evaluation of Ellenburger reservoirs in West Texas has been an uncertain matker at best because of the lack of cores and suitable core-analysis method. Large amounts of oil arc produced from sections from which sample cuttings are obtained that contain litile porosity and no oil saturation. It has long been realized that the formation in some areas contained numerous fractures and solulion cavities that probably contained the major part of the oil present but the magnitude of the porous system conltaining oil has been unknown. Diamond coring cquipmene, used in the mining industry lor many years, has been developed for oil-field use to obtain high core recovery in fractured dolomite that is not possible with conventional coring equipment. A 36ft section of the core recovered from a fractured Ellenburger reseivoir waS analyzed by a unique but simple method to obtain the first defmite evaluation of one section of the producing formation. The cores and the method of analysis used are described and the results arc discussed in some detail. Discussion The first successful known analyses of cores recovered from the Ellenburger formation in the Permian Basin area were made on cores recovered with the use of diamond core heads. Conventionul coring methods previously used have had lour core recovery and standard methods of analysis have proved to be inadequate for evaluation of those cores that were recovered. Core Descriplion The Ellenburger formation to be dis cussed was cored using diamond core heads and oil-base drilling fluid. Of the total 103 ft cored to a depth of 8893 ft in the Ellenburger, 99 ft or 96 pct was recovered. The dolomite cores were described as gray to white, crystalline to coarscIy crystalline, with chert and calcite inclusions. Occasional shale partings ? to ¼ in. in width were noted. A small amount of green clay was found in some of the coarsely crystalline material. So intergranular porosity was found by inspection in any of the cores. The core urns highly fractured over most of its length with not more than two continuous feet that failed to contain fractures. The fractures Were nearly vertical and varied in width from those harely visible to as much as one millimeter. Scattered solution voids, or vugs, as large as 3 cm in diameter occurred in association with same •a

Jan 1, 1949

By H. E. Lee, A. W. Edelen

The Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. Ill the ore lenses the sulphides appear as a massive, very fine-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. Introduction The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre-Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Tezintlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short linc, Shay-geared locomotives arc used for the transportation of concentrates and supplies.

Jan 1, 1941

By J. J. Rutledge

The United States Bureau of Mines established at Bruceton, Pa., in 1909, an experimental mine, for the purpose of testing the means of preventing and limiting mine explosions. During the last ten years numerous explosions have been caused to originate in this mine for investigative purposes and the rate of propagation of the explosion wave, the pressure developed per unit of area by the explosions, and the general results of the explosions have been carefully recorded and studied. Means of preventing mine explosions or of limiting them to the areas in which they originate have been developed. A great deal of valuable information has been derived from the work in this mine and much more useful and Valuable information will be obtained in the future. The writer would plead, not for the opening of experimental mines in all the important coal-producing fields in the United States, but for the opening of demonstration mines, or mines in which experiments could be made with the various details of coal mining. The United States Department of Agriculture has established, in nearly every state, stations that undertake experimental work for the benefit of the agricultural interests. In addition, small demonstration plats are set aside, in suitable locations in the farming districts, where various crops are grown under scientific direction, so that the faimers in the neighborhood can note the results obtained and profit thereby. Something like this should be done for the coal-mining induatry. If experimental or demonstration mines were established, methods of working adapted to local conditions could be worked out. Owing to competition in the same markets, small capitalization, or low profits, it may be an utter impossibility for any one company to try a new method of mining. Labor conditions may prevent the trial of a new method of working. It may be impossible or inadvisable to disturb existing working conditions for fear of causing trouble among the miners through real or fancied changes in the scale of wages. The first and most important investigation to be undertaken in these demonstration mines would be the trial of various methods of working coal mines until a satisfactory plan had been demonstrated for each

Jan 1, 1920

By Fred T. Greene

Most of the recent discussion of the mineral land law published in the Transactions is in the abstract—an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversyll which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the 1east. of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the "Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40' W., dipping about 40" to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80" W. and dips at high angles to the north and south. The movement on the Wardner foot wall is apparently normal, and there has been more or less brecciation on either side of it; but as the moving mass was that above the foot wall, the brecciation has been more complete on that side, and has extended farther from the plane of movement. Many minor faults, generally of insignificant extent, resulted from the movement along the Wardner foot wall. Most of these were

Jan 1, 1916

By J. A. Meech

"The technology known as Expert Systems is being used within the minerals industry in a wide variety of problem areas. Applications include diagnosis, prediction, training, monitoring and control. Expert Systems provide a way to program computers to imitate human thinking. The construction of such systems is a straight-forward task that can be quickly learned by novices but can require a lifetime to master.To assist in the understanding and utility of this technology, a special manual bas been prepared which operates on a microcomputer under the MS-Windows environment. The manual covers all aspects of Artificial Intelligence of relevance to Expert Systems. A hypertext system allows users to probe as d•~ply as needed to achieve understanding or to simply skim the surface of the knowledge to obtain a quick overview of subjects. The manual was developed under the sponsorship of the Mineral Sciences Laboratory of CANMET and is available from the Mining and Mineral Process Engineering Department at the University of British Columbia. Annual updates are planned to keep abreast of new developments in this rapidly changing technology. RESUMELa technologie: des Systèmes Experts est utilisée par l'industrie minière pour résoudre une grande variété de problèmes. Les domaines d'application comprennent le diagnostic, la prédiction, la formation, la surveillance et le contrôle des procèdes. Les Systèmes Experts permettent d'écrire des programmes d'ordinateur qui imitent le processus de la pensée humaine. La construction de tels systèmes e:st une tâche qui peut être apprise rapidement mais qui peut prendre des années à maitriser.Pour aider à mieux comprendre et utiliser cette technologie, un manuel spécial opérant sur microordinateur dans l'environnement Windows a été développe. Le manuel couvre tous les aspects de l'intelligence artificielle qui concement les Systèmes Experts. Un système ""hypertexte"" permet à l'utilisateur d'étudier un sujet en profondeur ou de simplement couvrir une grande variété de sujet en surface. Le manuel a été développe avec l'aide financière du Laboratoire des Sciences Minérales de CANMET et est disponible au Département de Génie Minier et Minéralurgique de l'Université de la Colombie Britannique. Des mises à jour annuelles sont prévues de manière à couvrir les changements et nouveautés de cette technologie en évolution."

Jan 1, 1993

By AIME AIME

W. R. CHEDSEY first saw the light of day in Boulder, Colo., in 1887, and will celebrate his birthday on Feb. 11. Mining early attracted him, so he went to the Colorado School of Mines, from which he received his E.M. in 1908, and an honorary doctor's degree thirty years later. The next three years he spent at the University of Idaho, doing special work in mechanical and electrical engineering and serving as associate professor of mining engineering. Leaving Idaho in 1911 he went to Central America as chief engineer and general superintendent of the Central American Development Co. The next year he jumped several thousand miles to the north to become chief engineer and assistant general manager of the Alaska Exploration Co. But teaching was Chedsey's choice so he returned to his alma mater, serving on the faculty at Golden from 1913 to 1916. Then to Penn State where he was professor of mining for 21 years, until going to Rolla to become director of the Missouri School of Mines and Metallurgy in 1937.

Jan 1, 1940

If the Journal is to fulfill its mandate to the mining and metallurgical industry, it needs to expand its readership and, by implication, membership of The South African Institute of Mining and Metallurgy. This we hope to do by increasing the appeal of the Journal to a wider audience through the inclusion, in addition to our high-quality research papers, of equally high-quality papers, articles, and contributions that will be of interest to our less research-minded members.

Jan 1, 1990

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economically entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transportation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotivcs are replacing coal in some places, where railroads operating high-speed passenger trains are willing, temporarily at least, to pay a premium for the fuel that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly established, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be rcquired in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bituminous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1936

By Harry W. Brown

This paper presents results of static capillary pressure measprements made both by the restored-state and by the mercury-injection methods, and of dynamic capillary pressure measurements made by the Hassler technique. The results indicate a variation from sample to sample of the factor used to convert capillary pressure obtained by mercury injection to those applicable to a water-gas system. Static capillary pressures measured by the restored-state method were found to be in close agreement with dynamic capillary pressures, indicating that data obtained from static measurements may be utilized with confidenre in the solution of dynamic problems of fluid flow. Experimental data are presented on the use of "J-curves" for the correlation of capillary pressure-saturation relations for a number of cores from a particular geologic formation. It is shown that the correlation was improved in some cases by reqtricting it to rertain lithologic classifications. INTRODUCTION The Meaning and Importance of Capillary Pressure The coexistence of two or more immiscible fluids within the voids of a porous medium, such as reservoir rock, gives rise to capillary forces. Because of the interfacial tension existing at the boundary between two immiscible fluids in a pore space, the interface is curved, and there is a pressure difference across the interface. This pressure difference is termed the capillary pressure. The magnitude of the capillary pressure between two immiscible fluids which together fill a porous medium depends upon several factors: the textural properties of the medium, the wettability of the medium, the interfacial tension between the fluids, the respective saturations of the fluids, and the manner in which these saturations are attained. For a given pair of immiscible fluids in a particular sample of reservoir rock, the capillary pressure is a unique function of the fluid saturation, provided that the saturation of the fluid which wets the rock has previously been decreased unidirectionally from an initially complete saturation. Similarly, for a given pair of fluids at a particular saturation which has been achieved by a

Jan 1, 1951