Search Documents

By Russell K. McFarland, Gloria T. Saxton

Introduction The March 1969 issue of Civil Engineering contained on article entitled "BART" Subway Construction: Planning and Costs" authoried by Thomas R. Kuesel. This article describes in some detail the innovations developed in planning and management to undertake the design and construction of the BART Project. This 75 mile long system contained 17 miles of urban tunnels and 13 subsurface stations. Within this article Mr. Kuesel very nicely listed the cost of the 70,000 linearfeet of bored tunnel, 23,380 linearfeet of cut and cover tunnel, and the costs of the thirteen underground stations. Ten years subsequent to the publishing of Mr. Kuesels article, it is very sobering to realize that San Francisco obtained a bargain of a magnitude that we are just beginning to realize. Table 1 is a listing of tunneled line sections taken from the paper. The average cost shown in this figure, including sections constructed under compressed air is $1,620 per foot of tunnel, with bid dates ranging from June 1966 thru October 1968. This average cost translated to about $16 million per double track mile of twin tunnel system.

Jan 1, 1979

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002

Jan 1, 1930

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lime Companys new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By A. S. Mallicis, Li Xiawoei, P. W. Weiblen, I. Iwasakl

Platinum group metals (PGM) are often found in close association with arsenide and sulfarsenide minerals in copper-nickel bearing gabbroic rocks. Major losses of platinum in flotation have been attributed to the susceptibilities of the arsenic minerals to oxidation and subsequent losses of their recoveries in cleaner flotation stages. The use of a nitrogen atmosphere in grinding and in flotation, the effectiveness of activation for improving their floatabilities, and the role that electrochemical interactions play not only between grinding media and minerals, but also among different minerals, are discussed.

Jan 1, 1989

By Stanislaw Wasilewski, Zdzislaw Krzystanek, Boleslaw Firganek

The experimental system for mine venti1ation control in Staszic colliery has two - level structure. In the lower - measuring 1evel the existing computer - based early fire detection system has been used completed with a number of additional sensors needed for ventilation parameters monitoring. The higher 1evel is a secondary computer equipped with a suitab1e dedicated software performing data processing according to the control a1gorithm. Direct control of air flow in a selected mine district is performed by means of a remotely controlled automatic regulator. Apart from functional tests of the system and its elements some research work has been carrying out in the colliery based on observations of transient effects caused by changes in air flow distribution.

Jan 1, 1989

By E. M. Timoshenko

Autoclave technology can be effectively used for liberation of complex mineral raw materials to transfer valuable constituents into solution for their subsequent recovery or to refine feed material in order to remove deleterious impurities, e.g. arsenic. The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs, high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: - Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); - Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially at the stage of liberation (chemical upgrading) of raw materials are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent).

Jan 1, 2006

We have been exploring for minerals in Australia for over 100 years and our methods are constantly improving - but why do we pros- pect? Is the effort justified? Obviously the main motive is economic gain. It is now and always has been but conditions are changing rapidly. Once it was the prospector who could cash the nugget. Then it was the syndicate, the small company, an amalgamation of small companies, the large company, the corporation; the multinational corporation - where do we go from there? Early there was personal satisfaction and excitement in out-door activity which gave scope for individual energy, hope and in some cases reward. There still remains the satisfaction, either individual or corporate that a mineral discovery creates new wealth and makes a contribution to the nation's well being. Parallel with developments has always been the growth of restraints on exploration, frequently out of phase with the current mineral developments - miners' rights, licences, titles, royalties, mining laws and regulations, taxation etc. As the operations have become more complex so the restraints have become more confining until it is now very necessary to question whether the chances of economic gain justify the risk and responsibility of mounting costly mineral exploration leading-to extensive capital development.

Jan 1, 1974

By David Akers, Clifford Raleigh, Glenn Shirey

Under a Cooperative Agreement with the U.S. Department of Energy’s National Energy Technology Laboratory (NETL) and the Mining Industry of the Future Program, CQ Inc. is demonstrating the GranuFlow™ process for improving the recovery of fine-sized coal in commercial coal preparation facilities. The State of Pennsylvania’s Energy Harvest Grant Program is also providing funding for this project. The GranuFlow technology involves the addition of an asphalt emulsion to a slurry of fine-sized coal (<100 mesh or 0.15 mm, typically froth flotation concentrate) before mechanical dewatering in screen-bowl centrifuges. The emulsion selectively agglomerates the carbon-rich particles, resulting in increased particle size and improved recovery of the coal fines during the dewatering process. This paper summarizes the test conditions and current results for both bench-scale investigations and full-scale commercial plant demonstrations.

Jan 1, 2005

By W. Kuckshinrichs

Metallic raw material flows are characterized by a complex global network of producers and consumers, as well as by a multitude of ecological, economic and social impacts across national boundaries and on different scales. This leads to the need to develop methodologies, which allow identifying obstacles that prevent metallic raw material flows to contribute to sustainable development. From a scientific point of view CRC 525 (Martens 2003) has developed an holistic indicator set consisting of approximately 80 different indicators. This set is taking into account the multi-dimensional character of sustainable development. Moreover the indicators reflect different system boundaries according to different actor levels and decision contexts. The full indicator set is important in scientific considerations and suitable for scientific awareness creation. However, to fulfil the function of a decision support approach for political and economic decision-makers some modifications are of central concern. At first a reduction of the full indicator set by selection of core indicators enables decision-makers to deal with complex issues of contrary economic and societal protection targets. Secondly, as thresholds of indicators justify societal call for action, they are discussed against its political or scientific origin. The proposed methodology is exemplified by indicator-based studies of the material flow of aluminium.

Jan 1, 2003

By William E. Ford, Edward Salisbury Dana

239, Contact-Gwiorneters. - The interfacial angles of crystals are measured by means of instruments which are called goniometers. The simplest form is the contact- or hand-goniometer one form of which is represented in Fig. 377. This contact-goniometer consists of a card on which is printed a semi- circular arc graduated to half degrees at the center of which is fastened a celluloid arm which may be turned to any desired position. The method of use of the goniometer is illustrated in Fig. 377. The bottom of the card and

Jan 1, 1922

The Victorian State Government recognises that the extensive brown coal deposits in Victoria are one of the State&apos;s key competitive strengths for economic development. The unique properties of the coal, together with the ease of open cut mining, make it suitable for a variety of new applications. Research and development activities are centred around applications which take advantage of the natural attributes and unique properties of the coal. The high reactivity and low ash content of the coal led to its selection for the Japanese brown coal liquefaction pilot plant currently operating in the Latrobe Valley, with support from the Victorian Government and the Coal Corporation of Victoria. Research and development of new brown coal based products together with many other areas of applied and fundamental research are being conducted in Victoria by Government research organisations, tertiary insti- tutions and private industry, with the objective of establishing new indus- trial developments based on Victoria&apos;s vast brown coal resource.

Jan 1, 1989

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By E Topal

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

By E. B. McNew, J. M. Barnes, A. E. Torma

The applicability of biosorbent materials for the removal of uranium and other heavy metals from synthetic and actual uranium mil 1 tailing (UMT) solutions has been investigated. The biosorbent materials used in this study were barium loaded beads of alginate, alginate-dextran sulfate, alginate-carrageenan, and alginate-xanthan gum. These studies were performed in stirred vessels and packed columns. It was observed that 100 percent of the uranium could be removed from a synthetic solution following 2 hours of contact time in a stirred vessel, and 80-100% of U, V, Mo, Mn, Sr, and Zn could be removed from a UMT effluent solution with a packed column. Kinetic evaluations were performed, using a generalized rate equation, on the biosorption of uranium with these barium loaded beads.

Jan 1, 1992

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By A. J. Lynch, N. W. Johnson, D. J. McKee, G. C. Thorne

The behaviour of minerals in sulphide flotation processes, with reference to simulation and control. by A. J. LYNCH, Ph.D., N. W. JOHNSON, Ph.D., D. J. McKEE, Ph.D., and G. C. THORNE, B.Sc. (Hons.) (Visitors) In sulphide flotation processes, there are two mechanisms by which particles are transferred from the flotation pulp to the concentrate: adhesion to air bubbles and natural flotation, and entrainment in the froth. The entrainment mechanism is particularly important for particles of non-sulphide gangue, which do not absorb collector. The importance of controlling the recovery rate of water was illustrated in plant testwork in which selectivity between valuable sulphides and sulphide gangue, and between valuable sulphides and non-sulphide gangue, was altered by manipulation of variables affecting the water recovery rate. The two mechanisms should be recognized in the development of a control system. Most of the control schemes in operating plants have concentrated on reagent additions, which affect the natural flotation mechanism. Although control of the chemical environment is clearly of paramount importance in flotation, plant tests have shown that control of the variables affecting the entrainment mechanism is also important.

Jan 4, 1974

By William Wraith

The availability of computer resources and data management technology, together with the prudent use of scientific management concepts, has made it possible to achieve important improvements in the control of maintenance and materials activities in the mining and minerals processing organization. The introduction of minicomputers and. the greatly improved efficiency of computer systems in general have put the use of computer technology within the reach of even the smaller mining companies which probably could not have afforded them just five to ten years ago. A number of progressive companies have implemented computer-based maintenance, purchasing, and supply inventory control systems. Using modern safety stock, demand forecasting, parts reliability analysis, and other control concepts, these new systems have helped minimize production losses by reducing the frequency and severity of supply shortages and unplanned repairs. At the same time, these systems are helping to conserve scarce capital resources by better utilization of supply inventory investments, reduced expenditures for maintenance, less frequent equipment replacements due to improved maintenance reliability, and greater capacity utilization of existing facilities.

Jan 1, 1979

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008